3UF5011-3AN00-1模块备件

3UF5011-3AN00-1

基金会现场总线高速以太网（FF HSE）
基金会现场总线（FF）是一种基于国际标准的现场总线协议
适用于制造业、工艺和应用的标准和规范
自动化和楼宇自动化。本现场总线标准的指南如下：
由现场总线基金会出版。
FF定义了两个通信配置文件，H1和HSE。H1配置文件允许
传输速率为31.25kbit/s。它优选地用于直接通信
在一个链路（H1链路）中的现场设备之间。HSE简介基于标准
以太网首先是H1和H1之间链路的强大主干
部分。典型的传输速率为：10Mbit/s或100Mbit/s。一
已在市场上提供并支持HSE档案的设备为FF
链接设备（例如LD 800HSE）。它们是两个国家之间的门户
H1段和HSE主干上的现场设备。
基金会现场总线通过高性能总线与AC 800M相连
HSE总线使用FF链接设备。
有关HSE概况的更多详细信息，请参见FF规范。
FF规范中解释了HSE背后的基本概念
系统架构（FF-581）和HSE概要（FF-941）。
FF子系统由FF链接设备组成（例如LD 800HSE，参见
附录C，推荐组件）相互通信
使用HSE协议。FF链接设备通常提供多个
基金会现场总线H1段（H1链路）。FF链接设备与设备
42c类允许处理在子公司上周期性发布的数据
H1段将在HSE段上“重新发布”。通过使用HSE重新发布，
可以配置不同网络上的现场设备之间的循环通信
HSE段上的H1段和装置。基金会现场总线HSE
网络和设备由现场总线生成器配置
基金会现场总线。
FF子系统通过一个接口与IEC 61131控制器（AC 800M）连接
AC 800M中的FF HSE装置CI860，参见39页的图7。从
FF的HSE单元是一个参与HSE的HSE装置
表达
I/O系统3节配置
166 3BSE036351-510 A
FF链接设备用作AC 800M和现场设备之间的网关
在H1段上，既用于现场设备的配置数据
处理在AC 800M和现场设备之间循环交换的数据。
图58.基金会现场总线HSE系统结构示例
3节I/O系统的配置
3BSE036351-510 A 167
TRIO/Genius远程I/O
TRIO是一款Genius远程I/O产品，提供离散、模拟和高速数据传输
用于连接AC 800M的计数器块。I/O块单元的配置
并且使用Control Builder M完成CI862。
驱动系统3节配置
168 3BSE036351-510 A
驱动系统
ABB标准（Std）和工程（Eng）驱动器可连接至AC 800M
通过以下任一项：
•光学模块总线
•CI801和PROFIBUS DP
•NPBA-12、RPBA-01或FPBA-01 PROFIBUS DP适配器模块
对于CI854
•RETA-02或FENA-01/-11以太网适配器模块以及CI871
（PROFINET IO）
•CI858驱动总线接口。
模块总线
在单CPU配置中，ABB驱动器可以通过以下方式连接到处理器单元：
光学模块总线。参见171页的图59。ABB驱动器的数量
可以连接到光学模块总线的光学模块总线可以由
以下等式：
（ABB驱动器数量）<84-（12个（TB820数量））
也就是说，每个驱动器使用一个ModuleBus群集。
PROFIBUS DP和CI801
在单CPU和冗余CPU配置中，ABB驱动器可以通过
PROFIBUS DP和CI801。参见171页的图59。只能使用标准驱动器
连接到CI801。每个驱动器可以连接十四（14）个标准驱动器
如果没有连接I/O单元，则为CI801。对于可以使用的驱动器的数量
当I/O单元（TB820）和标准驱动器都被连接时
已连接，请参阅有关PROFIBUS DP FCI的文档。
有关ABB驱动器及其类型（Std和Eng）的更多信息，请参阅
S800 I/O文档。
有关分支装置的信息（171页图59），请参阅ABB驱动
系统文档。
ABB驱动器也可以通过PROFIBUS DP（CI854/CI854A）连接，直接
连接到PROFIBUS DP从模块NPBA-12、RPBA-01和FPBA-01。
3节驱动系统的配置
3BSE036351-510 A 169
PROFINET IO和CI871
RETA-02以太网适配器模块和FENA-01/-11以太网适配器
模块是ABB驱动器的可选设备，可连接
驱动到PROFINET IO（PNIO）网络。该驱动器被视为PNIO设备
在PROFINET IO网络上，它与所有PNIO控制器兼容
支持PROFINET IO和子插槽的工作站。
驱动总线接口CI858
ABB驱动装置可通过CI858装置连接到AC 800M，见图59
pag

3UF5011-3AN00-1

3UF5011-3AN00-1

FOUNDATION Fieldbus High Speed Ethernet (FF HSE) FOUNDATION Fieldbus (FF) is a fieldbus protocol based on international standards and designed for applications in the manufacturing industry, process automation and buildings automation. The guidelines for this fieldbus standard are published by the Fieldbus Foundation. FF defines two communication profiles, H1 and HSE. The H1 profile allows a transmission rate of 31.25 kbit/s. It is preferably used for direct communication between field devices in one link (H1 link). The HSE profile is based on standard ethernet serves first and foremost as a powerful backbone for the link between H1 segments. Typically transmission rates are: 10 Mbit/s or 100 Mbit/s. The first devices that are already available on the market and support the HSE profile are FF linking devices (for example LD 800HSE). They serve as a gateway between the field devices on the H1 segments and the HSE backbone. The FOUNDATION Fieldbus is linked to the AC 800M via the high-performance HSE bus using FF linking devices. More detailed information on the HSE profile can be found in the FF specifications. The fundamental concepts behind HSE are explained in the FF specifications System Architecture (FF-581) and HSE Profiles (FF-941). The FF subsystem consists of FF linking devices (for example LD 800HSE, see Appendix C, Recommended Components) which communicate with one another using the HSE protocol. An FF linking device usually provides more than one FOUNDATION Fieldbus H1 segments (H1 link). FF linking devices with a device class of 42c allow process data that have been published cyclically on the subsidiary H1 segments to be “republished” on the HSE segment. By using HSE republishing, it is possible to configure cyclical communication between field devices on different H1 segments and devices on the HSE segment.The FOUNDATION Fieldbus HSE and H1network and the devices are configured with the Fieldbus Builder FOUNDATION Fieldbus. The FF subsystem is interfaced to the IEC 61131 controller (AC 800M) using a FF HSE unit CI860 in the AC 800M, see Figure 7 on page 39. From the perspective of FF the FF HSE unit is an HSE device which participates in the HSE communication. I/O Systems Section 3 Configuration 166 3BSE036351-510 A FF linking devices operate as gateways between the AC 800M and the field devices on the H1segments both for the configuration data of the field devices and for the process data which is exchanged cyclically between AC 800M and the field devices. Figure 58. Example of system structure for FOUNDATION Fieldbus HSE Section 3 Configuration I/O Systems 3BSE036351-510 A 167 TRIO/Genius Remote I/O TRIO is a Genius remote I/O product that provides discrete, analog and high-speed counter blocks for connection to the AC 800M. Configuration of the I/O block units and the CI862 is done using Control Builder M. Drive System Section 3 Configuration 168 3BSE036351-510 A Drive System ABB Standard (Std) and Engineered (Eng) Drives can be connected to AC 800M through any of the following: • The optical ModuleBus • CI801 and PROFIBUS DP • NPBA-12, RPBA-01, or FPBA-01 PROFIBUS DP Adaptor modules along with CI854 • RETA-02 or FENA-01/-11 Ethernet Adapter modules along with CI871 (PROFINET IO) • CI858 DriveBus Interface. ModuleBus In single CPU configuration, ABB Drives can be connected to the processor unit via the optical ModuleBus. See Figure 59 on page 171. The number of ABB Drives which can be connected to the optical ModuleBus, can be described by the following equation: (No. of ABB Drives) < 84 - (12 x (No. of TB820s)) that is, each Drive uses one ModuleBus cluster. PROFIBUS DP and CI801 In single and redundant CPU configuration, ABB Drives can be connected via PROFIBUS DP and CI801. See Figure 59 on page 171. Only Standard Drives can be connected to CI801. Fourteen (14) Standard Drives can be connected to each CI801 if there are no I/O units connected. For the number of Drives that can be connected to the same CI801, when both I/O units (TB820) and Standard Drives are connected, refer to documentation about FCI for PROFIBUS DP. For more information about ABB Drives and its types (Std and Eng) refer to S800 I/O documentation. For information about Branching Unit (Figure 59 on page 171) see ABB Drive System documentation. ABB drives can also be connected via PROFIBUS DP (CI854/CI854A), with direct connection to PROFIBUS DP slave modules NPBA-12, RPBA-01, and FPBA-01. Section 3 Configuration Drive System 3BSE036351-510 A 169 PROFINET IO and CI871 The RETA-02 Ethernet Adapter module and FENA-01/-11 Ethernet Adapter module are optional devices for ABB drives, which enables the connection of the drive to a PROFINET IO (PNIO) network. The drive is considered as a PNIO device on the PROFINET IO network, and it is compatible with all PNIO controller stations that support PROFINET IO and sub-slots. DriveBus Interface CI858 ABB drives can be connected to the AC 800M via the CI858 unit, see Figure 59 on page 171 and Figure 60 on page 172. The drive interface can be used for controlling up to 24 drives or inverter units. Main communication functions of the drive connection are: • Dataset communication • Broadcast system time • Supervision and diagnostics functions The data exchange between the AC 800M and the CI858 consists of eight datasets. The drive connection is able to transfer at the maximum 8 datasets / 1 ms. Connection of multiple drives requires the use of a branching unit, which enables the construction of a logical bus with physical star topology, see Figure 60 on page 172. The branching units can be chained. The following drives are supported by the drive connection: • ACS 600 single drive • ACS 600 multi drive • ACS 600 thyristor supply units • ACS 600 IGBT supply units • ACS 800 product family • ACS 140-AC S400 • DCS 600 and DCS 400 • ACS 6000 product family/large drives