5C5601模块备件

5C5601

CI865装置上的R（un）和F（ault）指示灯均未亮起。正在安装
配置。留出时间完成这项工作。
如果该状况持续存在且没有其他原因
CEX总线上的单元LED亮起：
•检查是否存在有效的硬件配置
包括CI865
到控制器。
•检查电源内的CEX总线保险丝
PM8xx处理器单元
•从以下位置启动复位信号（INIT）：
PM8xx处理器单元
•更换CI865装置
CI865装置上的F（ault）指示灯亮起，正在进行校准
重新启动。留出时间完成这项工作。
如果故障依然存在，请更换单元。
COM A/COM B LED关闭、关闭电源或重置模式
COM A/COM B指示灯呈稳定绿色，通道正常
COM A/COM B指示灯呈绿色闪烁。临时错误或需要初始设置
COM A/COM B LED为实心红色模块损坏，必须更换
COM A/COM B指示灯呈红色闪烁。坏通道电缆
COM A/COM B LED为铁路红色。道路未正确配置用于
网络
COM A/COM B指示灯呈红色/绿色闪烁。网络存在数据流问题
COM A/COM B LED为铁路红色/绿色自检
CI865支持热插拔。
第5节Modbus TCP接口的维护–CI867
3BSE036351-510 A 225
Modbus TCP接口–CI867
表42.Modbus TCP接口CI867-故障查找
故障、可能原因和纠正措施
R（un）和F（ault）LED均不可用
这句话的意思是：
CI867单元正在安装中
配置。留出时间完成这项工作。如果
这种情况持续存在，并且没有其他装置发光
在CEX总线上点亮：
•检查是否存在有效的硬件配置
包括CI867下载到
控制器。
•检查电源内的CEX总线保险丝
PM8xx处理器单元。
•从控制器启动复位信号（INIT）
PM8xx处理器单元。
•更换CI867装置。
CI867装置上的F（ault）指示灯亮起，正在进行测试
重新启动。留出时间完成这项工作。
如果故障依然存在，请更换单元。
RxTx1/RxTx2指示灯熄灭，没有接收或传输活动
相应的以太网信道。
RxTx1/RxTx2指示灯闪烁，表示各自的接收或发送活动
以太网信道正常。
PRIM在非冗余模式下关闭：
•此模块不是由主机启动的
应用
在冗余模式下：
•此模块不是由主机启动的
应用程序或此模块充当
备份接口。
Modbus TCP接口–CI867第5节维护
226 3BSE036351-510 A
PRIM在非冗余模式下打开：
•该模块由主机启动
应用
在冗余模式下：
•该模块由主机启动
应用程序和此模块充当
主接口。
双在非冗余模式下关闭：
•在非冗余状态下，此开关始终关闭
模式
在冗余模式下：
•该模块不同步，或者
该冗余对中的其他模块为：
这不是开始。
DUAL在非冗余模式下打开：
•不适用
在冗余模式下：
•该模块不同步，或者
该冗余对中的其他模块为：
这不是开始。
CI867支持热插拔。
表42.Modbus TCP接口CI867-故障查找
故障、可能原因和纠正措施
第5节维护IEC 61850接口–CI868
3BSE036351-510 A 227
IEC 61850接口–CI868
表43.IEC 61850接口CI868-故障查找
故障、可能原因和纠正措施
R（un）和F（ault）LED均不可用
这句话的意思是：
CI868单元正在安装过程中
配置。留出时间完成这项工作。如果
这种情况持续存在，并且没有其他装置发光
在CEX总线上：
•检查是否存在有效的硬件配置
包括CI868下载到
控制器。
•检查电源内的CEX总线保险丝
PM8xx处理器单元。
•从控制器启动复位信号（INIT）
PM8xx处理器单元。
•更换CI868装置。
•未下载任何应用程序。
CI868装置上的F（ault）指示灯亮起，正在进行校准
重新启动。留出时间完成这项工作。
如果故障依然存在，请更换单元。
RxTx1/RxTx2（1）LED熄灭
（1） 由于禁用通道CH2，LED将始终关闭
没有针对的接收或传输活动
相应的以太网信道。
RxTx1/RxTx2（1）指示灯闪烁，表示各自的接收或发送活动
以太网信道正常。
由于CI868不支持冗余

5C5601

5C5601

Neither R(un) nor F(ault) LED’s are ON The CI865 unit is in the process of being configured. Allow time for this to finalize. If the condition persists, and no other unit LED on the CEX-Bus is lit: • Check that a valid HW configuration including the CI865 is downloaded to the controller. • Check the CEX-Bus fuse inside the PM8xx processor unit • Initiate a reset signal (INIT) from the PM8xx processor unit • Replace the CI865 unit F(ault) LED is ON The CI865 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. COM A/COM B LED is OFF Power OFF or Reset Mode COM A/COM B LED is solid green Channel OK COM A/COM B LED is flashing green Temporary error or need initial setup COM A/COM B LED is solid red Module is broken, has to be replaced COM A/COM B LED is flashing red Bad channel cable COM A/COM B LED is railroad red The road is not configured right for the network COM A/COM B LED is flashing red/green Network has data flow problem COM A/COM B LED is railroad red/green Self test CI865 supports hot swap. Section 5 Maintenance Modbus TCP Interface – CI867 3BSE036351-510 A 225 Modbus TCP Interface – CI867 Table 42. Modbus TCP Interface CI867 - Fault Finding Fault Possible Cause and Corrective Action Neither R(un) nor F(ault) LED's are ON The CI867 unit is in the process of being configured. Allow time for this to finalize. If the condition persist, and no other unit LED on the CEX-Bus is lit: • Check that a valid HW configuration including the CI867 is downloaded to the controller. • Check the CEX-Bus fuse inside the PM8xx processor unit. • Initiate a reset signal (INIT) from the PM8xx processor unit. • Replace the CI867 unit. F(ault) LED is ON The CI867 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. RxTx1/RxTx2 LED is OFF No Receive or transmit activity for respective Ethernet channels. RxTx1/RxTx2 LED is flashing Receive or transmit activity for respective Ethernet channels is normal. PRIM is OFF In non-redundant mode: • This module is not started by the application. In redundant mode: • This module is not started by the application or this module act as backup interface. Modbus TCP Interface – CI867 Section 5 Maintenance 226 3BSE036351-510 A PRIM is ON In non-redundant mode: • This module is started by the application. In redundant mode: • This module is started by the application and this module act as the primary interface. DUAL is OFF In non-redundant mode: • This is always OFF in non-redundant mode. In redundant mode: • This module is not synchronized or the other module in this redundant pair is not started. DUAL is ON In non-redundant mode: • N/A In redundant mode: • This module is not synchronized or the other module in this redundant pair is not started. CI867 supports hot swap. Table 42. Modbus TCP Interface CI867 - Fault Finding Fault Possible Cause and Corrective Action Section 5 Maintenance IEC 61850 Interface – CI868 3BSE036351-510 A 227 IEC 61850 Interface – CI868 Table 43. IEC 61850 Interface CI868 - Fault Finding Fault Possible Cause and Corrective Action Neither R(un) nor F(ault) LED's are ON The CI868 unit is in the process of being configured. Allow time for this to finalize. If the condition persist, and no other unit LED on the CEX-Bus is ON: • Check that a valid HW configuration including the CI868 is downloaded to the controller. • Check the CEX-Bus fuse inside the PM8xx processor unit. • Initiate a reset signal (INIT) from the PM8xx processor unit. • Replace the CI868 unit. • None application is downloaded. F(ault) LED is ON The CI868 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. RxTx1/RxTx2(1) LED is OFF (1) LED will always be switched off due to disabling of channel CH2 No Receive or transmit activity for respective Ethernet channels. RxTx1/RxTx2(1) LED is flashing Receive or transmit activity for respective Ethernet channels is normal. Since CI868 does not support redundancy, the DUAL LE