X20BC0083

X20BC0083

Windows 2000和Windows XP。
附录D-Argon BIOS描述了与
远程以太网引导BIOS。
附录E-示例C软件提供了一个示例代码库的列表，其中
程序员可以利用它来构建应用程序。
概述11
工具书类
奔腾4处理器-MμFCPGA封装，1.7至2.2GHz
2003年1月，订单号250686-005
英特尔852GM图形和内存控制器集线器（GMCH）
2003年1月，订单号252338-001
英特尔82801DBM I/O控制器集线器4移动版（ICH4-M）
2003年1月，订单号252337-001
英特尔82540EM千兆以太网控制器
2003年4月
PCI本地总线规范，版本2.1
PCI特别利益集团
P、 邮箱14070
波特兰或97214
（800）433-5177（美国）
（503）797-4207（国际）
（503）234-6762（传真）
CMC规范，P1386/草案2.0，来自：
IEEE标准部
版权和许可
霍斯巷445号，邮政信箱1331
皮斯卡塔韦，NJ 08855-1331，美国
PMC规范，P1386.1/草案2.0，来自：
IEEE标准部
版权和许可
霍斯巷445号，邮政信箱1331
皮斯卡塔韦，NJ 08855-1331，美国
VMISFT-9420 IOWorks访问用户指南
博士。编号：520-009420-910
GE智能平台
南纪念公园12090号。
美国阿拉巴马州亨茨维尔35803-3308
(800) 322-3616
www.ge-ip.com
基于VMEbus接口的Tundra Universe II
博士。编号：500-000211-000
GE智能平台
南纪念公园12090号。
美国阿拉巴马州亨茨维尔35803-3308
(800) 322-3616
www.ge-ip.com
有关VMEbus的详细说明和规格，请参阅：
VMEbus规范C版和VMEbus手册
VMEbus国际贸易协会（VITA）
7825东格尔丁博士。
套房104
亚利桑那州斯科茨代尔85260
(602) 951-8866
（602）951-0720（传真）
www.vita.com
12 VMIVME-7805/VME-7805RC硬件参考手册
安全总结
在施工的所有阶段，必须遵守以下一般安全预防措施：
本产品的操作、服务和维修。未能遵守这些规定
本手册其他地方的预防措施或特定警告违反了安全性
本产品的设计、制造和预期用途标准。
对于客户未能遵守这些规定，GE不承担任何责任
要求。
接地
系统
为了大限度地减少冲击危险，机箱和系统机柜必须连接到：
电接地。应使用三芯交流电力电缆。这个
电源线必须插入经批准的三触点电气插头
插座或与带接地的三触点到两触点适配器一起使用
电线（绿色）牢固连接到电源处的电气接地（安全接地）
出口
请勿在以下位置操作：
炸药
气氛
请勿在存在易燃气体或烟雾的情况下操作系统。活动
在这种环境中，任何电气系统的运行都构成了一定的安全性
危险
远离
带电电路
操作人员不得拆除产品盖。部件更换
内部调整必须由合格的维护人员进行。做
不要用连接的电源线更换部件。在某些条件下，
即使拆下电源电缆，也可能存在危险电压。避免
如果有人受伤，请务必在触摸电源和放电电路之前将其断开。
不提供服务或
单独调整
除非另一个人有能力，否则不要尝试内部服务或调整
提供急救和复苏服务。
不要代替
零件或修改
系统
由于存在引入额外危险的危险，请勿安装替代品
或对产品进行任何未经授权的修改。归还
向GE提供产品服务和维修，以确保维护安全功能。
危险的
程序
警告
警告（如下面的示例）仅在潜在危险之前出现
本手册中的所有步骤。必须遵守警告中包含的说明
被跟踪。
警告
该系统中存在可能导致死亡的危险电压。
搬运、测试和调整时应格外小心。
概述13
警告，
告诫
和注释
警告
警告表示危险。它提醒人们注意一个程序、惯例或规则
如果未正确执行或遵守，可能导致以下情况：
人员伤亡。
注意安全
谨慎意味着危险。它提请注意操作过程，
如果未正确执行或遵守，可能导致以下情况的实践或条件：
导致部分或全部系统损坏或毁坏。
注
注释表示重要信息。它提醒人们注意一种程序、做法或条件
必须强调这一点。
小费
提示表示一些专家信息。
链接
这是链接文本。
14 VMIVME-7805/VME-7805RC硬件参考手册
1•搬运和安装
本章介绍了硬件跳线设置、连接器说明和其他功能，
VMIVME-7805/VME-7805RC的安装、系统设置和操作。
1.1开箱程序
应遵守运输集装箱中发现的任何预防措施。所有项目
应该谨慎地对待联合国

X20BC0083

X20BC0083

Windows 2000 and Windows XP. Appendix D - Argon BIOS describes the menus and options associated with the remote Ethernet booting BIOS. Appendix E - Sample C Software provides listings of a library of sample code that the programmer may utilize to build applications. Overview 11 References Pentium 4 Processor-M μFCPGA package at 1.7 to 2.2GHz January 2003, Order Number 250686-005 Intel 852GM Graphics and Memory Controller Hub (GMCH) January 2003, Order Number 252338-001 Intel 82801DBM I/O Controller Hub 4 Mobile (ICH4-M) January 2003, Order Number 252337-001 Intel 82540EM Gigabit Ethernet Controller April 2003 PCI Local Bus Specification, Rev. 2.1 PCI Special Interest Group P.O. Box 14070 Portland, OR 97214 (800) 433-5177 (U.S.) (503) 797-4207 (International) (503) 234-6762 (FAX) CMC Specification, P1386/Draft 2.0 from: IEEE Standards Department Copyrights and Permissions 445 Hoes Lanes, P.O. Box 1331 Piscataway, NJ 08855-1331, USA PMC Specification, P1386.1/Draft 2.0 from: IEEE Standards Department Copyrights and Permissions 445 Hoes Lanes, P.O. Box 1331 Piscataway, NJ 08855-1331, USA VMISFT-9420 IOWorks Access User’s Guide Doc. No. 520-009420-910 GE Intelligent Platforms 12090 South Memorial Pkwy. Huntsville, AL 35803-3308 (800) 322-3616 www.ge-ip.com Tundra Universe II Based VMEbus Interface Doc. No. 500-000211-000 GE Intelligent Platforms 12090 South Memorial Pkwy. Huntsville, AL 35803-3308 (800) 322-3616 www.ge-ip.com For a detailed description and specification of the VMEbus, please refer to: VMEbus Specification Rev. C. and the VMEbus Handbook VMEbus International Trade Assoc. (VITA) 7825 East Gelding Dr. Suite 104 Scottsdale, AZ 85260 (602) 951-8866 (602) 951-0720 (FAX) www.vita.com 12 VMIVME-7805/VME-7805RC Hardware Reference Manual Safety Summary The following general safety precautions must be observed during all phases of the operation, service and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of this product. GE assumes no liability for the customer's failure to comply with these requirements. Ground the System To minimize shock hazard, the chassis and system cabinet must be connected to an electrical ground. A three-conductor AC power cable should be used. The power cable must either be plugged into an approved three-contact electrical outlet or used with a three-contact to two-contact adapter with the grounding wire (green) firmly connected to an electrical ground (safety ground) at the power outlet. Do Not Operate in an Explosive Atmosphere Do not operate the system in the presence of flammable gases or fumes. Operation of any electrical system in such an environment constitutes a definite safety hazard. Keep Away from Live Circuits Operating personnel must not remove product covers. Component replacement and internal adjustments must be made by qualified maintenance personnel. Do not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and discharge circuits before touching them. Do Not Service or Adjust Alone Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present. Do Not Substitute Parts or Modify System Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification to the product. Return the product to GE for service and repair to ensure that safety features are maintained. Dangerous Procedure Warnings Warnings, such as the example below, precede only potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. WARNING Dangerous voltages, capable of causing death, are present in this system. Use extreme caution when handling, testing and adjusting. Overview 13 Warnings, Cautions and Notes WARNING WARNING denotes a hazard. It calls attention to a procedure, practice, or condition, which, if not correctly performed or adhered to, could result in injury or death to personnel. CAUTION CAUTION denotes a hazard. It calls attention to an operating procedure, practice, or condition, which, if not correctly performed or adhered to, could result in damage to or destruction of part or all of the system. NOTE NOTE denotes important information. It calls attention to a procedure, practice, or condition which is essential to highlight. TIP Tip denotes a bit of expert information. LINK This is link text. 14 VMIVME-7805/VME-7805RC Hardware Reference Manual 1 • Handling and Installation This chapter describes the hardware jumper settings, connector descriptions, installation, system setup and operation of the VMIVME-7805/VME-7805RC. 1.1 Unpacking Procedures Any precautions found in the shipping container should be observed. All items should be carefully unpacked and thoroughly inspected for damage that might have occurred during shipment. The board(s) should be checked for broken components, damaged printed circuit board(s), heat damage and other visible contamination. All claims arising from shipping damage should be filed with the carrier and a complete report sent to GE Customer Care. 1.2 Handling Precaution Electronic assemblies use devices that are sensitive to static discharge. Observe anti-static procedures when handling these boards. All products should be in an anti-static plastic bag or conductive foam for storage or shipment. Work at an approved anti-static workstation when unpacking boards. 1.3 Hardware Setup The VMIVME-7805/VME-7805RC are factory populated with user-specified options as part of the VMIVME-7805/VME-7805RC ordering information. The processor speed, memory size and CompactFlash memory size are not userupgradable. To change processor speeds or RAM/Flash size, contact Customer Care to receive a Return Material Authorization (RMA). GE Customer Care is available at: 1-800-433-2682 in North America, or +1-780-401-7700 for international calls. Or, visit our website www.ge-ip.com. The VMIVME-7805/VME-7805RC are tested for system operation and shipped with factory-installed head