A1SJ51T64 ensions，参见图1了解702-002型室内
外壳，图2适用于733-002型防风雨非金属外壳，图3适用于
732-102型防风雨金属外壳。安装机柜时，请小心避免
损坏内部接线板。所有电站外壳的建议安装高度为：
距离外壳中心线54英寸（137厘米）。
图1.702-002型室内外壳安装详图
酒吧42004-147H
型号702-002、732-102和733-002 24 V直流单方放大器外壳第5页，共12页
f： \standard ioms-当前版本\42004安装手册\42004-147h.doc
08/13
图2 733-002型室外非金属外壳安装详图
酒吧42004-147H
型号702-002、732-102和733-002 24 V直流单方放大器外壳第6页，共12页
f： \standard ioms-当前版本\42004安装手册\42004-147h.doc
08/13
图3.732-102型室外外壳安装详图
酒吧42004-147H
型号702-002、732-102和733-002 24 V直流单方放大器外壳第7页，共12页
f： \standard ioms-当前版本\42004安装手册\42004-147h.doc
08/13
装电线
将导管连接到外壳上。将接线穿过导管，并将其放入外壳中。看见
图4.仔细遵循导线颜色，因为颜色对应于GAI Tronics 60038系列
缆绳电线必须用铁锹牵引，并小心、完整地连接到接线板上。
不当的端接可能会降低站点性能。
局部静噪
图7显示了当电台完全组装和寻呼操作时的本地扬声器静音
发生。正常情况下，当按下“电台按到寻呼”按钮时，连接到该按钮的寻呼扬声器
电台被静音（静音），以防止对手持话筒的声音反馈。然而
当手机用于通话时，寻呼扬声器是“实时”的，以支持来自用户的寻呼呼叫
其他电台。
要禁用静音功能，请按照以下说明操作：
1.将连接到接线板上的端子点7（静音）上的锯齿形紫色导线定位在
圈占地
2.将锯齿状紫色导线转移至端子点8（第L1页）。
进行任何静音更改后，打开电台放大器的包装并安装。
相互静噪
在反馈发生在区域内并重新定位的情况下 A1SJ51T64 
A1SJ51T64
ensions, refer to Figure 1 for the Model 702-002 Indoor Enclosure, Figure 2 for Model 733-002 Weatherproof Non-metallic Enclosure, and Figure 3 for the Model 732-102 Weatherproof Metallic Enclosure. When mounting the enclosure, use caution to avoid damaging the terminal blocks inside. The suggested mounting height for all station enclosures is 54 inches (137 cm) up to the centerline of the enclosure. Figure 1. Model 702-002 Indoor Enclosure Mounting Details Pub. 42004-147H Model 702-002, 732-102, and 733-002 24 V DC Single-Party Amplifier Enclosures Page 5 of 12 f:\standard ioms - current release\42004 instr. manuals\42004-147h.doc 08/13 Figure 2. Model 733-002 Outdoor Non-metallic Enclosure Mounting Details Pub. 42004-147H Model 702-002, 732-102, and 733-002 24 V DC Single-Party Amplifier Enclosures Page 6 of 12 f:\standard ioms - current release\42004 instr. manuals\42004-147h.doc 08/13 Figure 3. Model 732-102 Outdoor Enclosure Mounting Details Pub. 42004-147H Model 702-002, 732-102, and 733-002 24 V DC Single-Party Amplifier Enclosures Page 7 of 12 f:\standard ioms - current release\42004 instr. manuals\42004-147h.doc 08/13 Wiring Attach conduit to the enclosure. Feed the wiring through the conduit, and bring it into the enclosure. See Figure 4. Follow the wire colors carefully, because the colors correspond to GAI-Tronics 60038 Series cable. The wires must be spade-lugged and connected carefully and completely to the terminal block. An improper termination may diminish station performance. Local Muting Figure 7 illustrates local speaker muting when stations are completely assembled and paging operation occurs. Normally, when the station push-to-page button is pressed, the paging speaker connected to that station is silenced (muted) to prevent acoustic feedback to the handset microphone. However, while the handset is in use for party line conversations, the paging speaker is “live” to enable paging calls from other stations. To disable the mute feature, follow these instructions: 1. Locate the lugged violet wire attached to terminal point 7 (mute) on the terminal block within the enclosure. 2. Transfer the lugged violet wire to terminal point 8 (Page L1). After any muting changes are made, unpack the station amplifier and install. Mutual Muting In the event that feedback occurs within an area and reposition | | |
