DEIF PPU-3模块备件

DEIF PPU-3

参数备份模式用于从一个数据库导出参数
驱动到另一个驱动器或备份驱动器参数。
上传到面板存储所有参数，包括两个用户集
以及对驱动器设置的超控（见17组：超控）
控制面板（操作员键盘）。全集，部分参数
然后可以设置（应用程序）、用户设置和覆盖设置
从控制面板下载到另一个驱动器或相同的驱动器
驾驶
控制面板内存是非易失性的，不依赖于
在电池板上。
根据电机和应用，以下选项：
在驱动器参数备份模式下可用：
•上传至面板–从驱动器复制所有参数
连接到控制面板。这包括所有定义的用户参数
设置、覆盖参数设置和内部（不可通过
用户）参数，例如由ID运行创建的参数）。
•备份信息–显示有关备份的以下信息：
参数已上传至面板的驱动器：
驱动器类型、驱动器额定值和固件版本。
•下载完整参数集–恢复完整参数集
从控制面板到驱动器。这写入所有参数，
包括内部非用户可调电机参数，
到驱动器。它不包括用户参数集或
覆盖参数集。
注意：仅在恢复驱动器时使用下载全套功能
从备份中，如果出现问题或要转移
与原始系统相同的系统参数。
•下载应用程序–复制部分参数
从控制面板到驱动器设置（整套的一部分）。
部分集合不包括用户集合、覆盖集合、和/或其他集合，
内部电机参数，参数9905…99091605，
1607、5201或任何51组：外部通信模块和
53组：EFB协议参数。
建议在使用相同的应用程序进行以下操作：
不同尺寸的驱动器。
•下载用户集1–复制用户集中的参数
从控制面板到驱动器设置1。用户集包括：
82启动和控制面板
ACH550-01用户手册
99组：启动数据参数和内部参数
电机参数。
必须首先使用参数9902 APPLIC保存用户集1
宏，然后上载到控制面板
可以下载。
•下载用户集2–复制用户集中的参数
从控制面板到驱动器设置2。作为下载
用户设置为1。
•下载覆盖集–将参数复制到
从控制面板到驱动器的超控设置。
必须首先保存覆盖（自动，如
组17：覆盖），然后上载到控件
下载前的面板是可能的

DEIF PPU-3

DEIF PPU-3
Parameter backup mode is used to export parameters from one drive to another or to make a backup of the drive parameters. Uploading to panel stores all parameters, including two user sets and an override (see Group 17: OVERRIDE) set, to the drive control panel (operator keypad). The full set, partial parameter set (application), user sets and override set can then be downloaded from the control panel to another drive or the same drive. The control panel memory is non-volatile and does not depend on the panel battery. Depending on the motor and application, the following options are available in the Drive parameter backup mode: • UPLOAD TO PANEL – Copies all parameters from the drive to the control panel. This includes all defined user parameter sets, override parameter set and internal (not adjustable by the user) parameters such as those created by the ID Run). • BACKUP INFO – Shows the following information about the drive whose parameters have been uploaded to the panel: drive type, drive rating and FW (firmware) version. • DOWNLOAD FULL SET – Restores the full parameter set from the control panel to the drive. This writes all parameters, including the internal non-user-adjustable motor parameters, to the drive. It does not include the user parameter sets or the override parameter set. Note: Use the Download full set function only to restore a drive from a backup if something has gone wrong or to transfer parameters to systems that are identical to the original system. • DOWNLOAD APPLICATION – Copies a partial parameter set (part of the full set) from the control panel to the drive. The partial set does not include user sets, override set, internal motor parameters, parameters 9905…9909, 1605, 1607, 5201, nor any Group 51: EXT COMM MODULE and Group 53: EFB PROTOCOL parameters. This is recommended when using the same application for drives of different sizes. • DOWNLOAD USER SET 1 – Copies the parameters in user set 1 from the control panel to the drive. A user set includes 82 Start-up and control panel ACH550-01 User's Manual Group 99: START-UP DATA parameters and the internal motor parameters. User set 1 must be first saved using parameter 9902 APPLIC MACRO and then uploaded to the control panel before downloading is possible. • DOWNLOAD USER SET 2 – Copies the parameters in user set 2 from the control panel to the drive. As DOWNLOAD USER SET 1 above. • DOWNLOAD OVERRIDE SET – Copies the parameters in the override set from the control panel to the drive. The override must be first saved (automatically, as defined by Group 17: OVERRIDE) and then uploaded to the control panel before downloading is possibl