VMIVME-7614-132 350-017614-132 D模块备件

VMIVME-7614-132 350-017614-132 D

必须连接dback信号
至模拟输入2（AI2）。默认情况下，设定点是从
控制面板，但也可以更改为模拟输入1。
工艺PI（D）必须通过以下方式进行调试和调整：
参数（组40：过程PID设置1）或使用PID
控制助理（推荐）。
ACH550-01用户手册
应用程序宏和布线117
1个SCR信号电缆屏蔽（屏幕）
2 AI1外部参考1:0（2）…10 V或0（4）…20 mA
3 AGND模拟输入电路公共
4 10V参考电压+10V直流电
5 AI2实际信号1:0（2）…10 V或0（4）…20 mA 2
6 AGND模拟输入电路公共
7 AO1输出频率：0（4）…20mA
8 AO2输出电流：0（4）…20mA
9 AGND模拟输出电路公共
10 24V辅助电压输出+24 V直流电
11 DI返回信号的接地公共线
12 DCOM数字输入通用于所有
13 DI1启动/停止：激活启动驱动器
14 DI2运行启用：停用将停止驱动器1
15 DI3设定点选择：设置1/设置2
16 DI4启动启用1：停用将停止驱动器1
17 DI5启动启用2：停用停止驱动器1
18未使用DI6
19 RO1C继电器输出1（1401段）
默认操作
已启动=>19连接到21
20 RO1A
21 RO1B
22 RO2C继电器输出2（1402段）
默认操作
运行=>22连接到24
23 RO2A
24 RO2B
25 RO3C继电器输出3（1403段）
默认操作
故障（-1）=>25连接到27
26 RO3A
27 RO3B
1使用参数1601、1608和1609禁用/启用2 AI2传感器由外部供电（图中未显示）。请参阅制造商的
说明书要使用由驱动辅助电压输出提供的传感器，请参阅124页。
注意：只有在可能的保护功能（运行启用或启动启用1和2）下，驱动器才会启动
2） 通过I/O激活或通过参数禁用。
1…10千欧
双设定点PID
ACH550-01用户手册
118应用程序宏和布线
12.具有恒定速度的双设定点PID
此应用程序宏可用于具有两个
恒速、主动PID和两种PID之间的交替PID
使用数字输入的设定点。当使用发射器时
信号可用作PID的过程实际值
控制器（AI2）或作为直接速度基准（AI1）。
PID设置点通过参数4011在驱动器内部设置
并且它们可以用DI3.PID改变
可通过参数或使用进行调试和调整
PID助理（推荐）。
数字输入（DI2）具有出厂设置的控制位置EXT1/EXT2
选择功能。当数字输入激活时
位置为EXT2，PID被激活。
数字输入4（DI4）和5（DI5）具有出厂设置常数
速度1和2功能。恒定速度1（1202段）为：
通过激活数字输入4（DI4）和恒速2进行选择
（1203段）通过激活数字输入5（DI5）。
ACH550-01用户手册
应用程序宏和布线119
1个SCR信号电缆屏蔽（屏幕）
2 AI1外部参考1:0（2）…10 V或0（4）…20 mA
3 AGND模拟输入电路公共
4 10V参考电压+10V直流电
5 AI2实际信号1:0（2）…10 V或0（4）…20 mA 2
6 AGND模拟输入电路公共
7 AO1输出频率：0（4）…20mA
8 AO2输出电流：0（4）…20mA
9 AGND模拟输出电路公共
10 24V辅助电压输出+24 V直流电
11 DI返回信号的接地公共线
12 DCOM数字输入通用于所有
13 DI1启动/停止：激活启动驱动器
14 DI2 EXT1/EXT2选择：激活使用PID
15 DI3设定点选择：设置1/设置2
16 DI4恒速1（1202段）1
17 DI5恒速2（1203段）1
18未使用DI6
19 RO1C继电器输出1（1401段）
默认操作
已启动=>19连接到21
20 RO1A
21 RO1B
22 RO2C继电器输出2（1402段）
默认操作
运行=>22连接到24
23 RO2A
24 RO2B
25 RO3C继电器输出3（1403段）
默认操作
故障（-1）=>25连接到27
26 RO3A
27 RO3B
1如果激活PID，则不可用
2 AI2传感器由外部供电（图中未显示）。请参阅制造商的
说明书要使用由驱动辅助电压输出提供的传感器，请参阅124页。
注意：只有在可能的保护功能（运行启用或启动启用1和2）下，驱动器才会启动
2） 从I/O激活或禁用

VMIVME-7614-132 350-017614-132 D

VMIVME-7614-132 350-017614-132 D

dback signal must be connected to analogue input 2 (AI2). By default, the setpoint is set from the control panel, but it can also be changed to analogue input 1. Process PI(D) must be commissioned and adjusted with parameters (Group 40: PROCESS PID SET 1) or using the PID control assistant (recommended). ACH550-01 User's Manual Application macros and wiring 117 1 SCR Signal cable shield (screen) 2 AI1 External reference 1: 0(2)…10 V or 0(4)…20 mA 3 AGND Analogue input circuit common 4 10V Reference voltage +10 V DC 5 AI2 Actual signal 1: 0(2)…10 V or 0(4)…20 mA 2 6 AGND Analogue input circuit common 7 AO1 Output frequency: 0(4)…20 mA 8 AO2 Output current: 0(4)…20 mA 9 AGND Analogue output circuit common 10 24V Auxiliary voltage output +24 V DC 11 GND Common for DI return signals 12 DCOM Digital input common for all 13 DI1 Start/Stop: Activation starts the drive 14 DI2 Run enable: Deactivation stops the drive 1 15 DI3 Setpoint selection: Set 1 / Set 2 16 DI4 Start enable 1: Deactivation stops the drive 1 17 DI5 Start enable 2: Deactivation stops the drive 1 18 DI6 Not used 19 RO1C Relay output 1 (par. 1401) Default operation Started => 19 connected to 21 20 RO1A 21 RO1B 22 RO2C Relay output 2 (par. 1402) Default operation Running => 22 connected to 24 23 RO2A 24 RO2B 25 RO3C Relay output 3 (par. 1403) Default operation Fault (-1) => 25 connected to 27 26 RO3A 27 RO3B 1 Disable/enable with parameters 1601, 1608 and 1609 2 The sensor for AI2 is powered externally (not shown in the figure). See the manufacturer’s instructions. To use sensors supplied by the drive auxiliary voltage output, see page 124. Note: The drive starts only if possible protection functions (Run enable or Start enable 1 and 2) are activated from I/O or disabled with parameters. 1…10 kohm Dual setpoint PID ACH550-01 User's Manual 118 Application macros and wiring 12. Dual setpoint PID with constant speeds This application macro can be used for applications with two constant speeds, active PID and alternating PID between two setpoints using digital inputs. When using a transmitter, the signal can be used as the process actual value for the PID controller (AI2) or as a direct speed reference (AI1). PID setpoints are set to the drive internally with parameters 4011 (set 1) and 4111 (set 2) and they can be changed with DI3. PID can be commissioned and adjusted with parameters or with the PID assistant (recommended). Digital input (DI2) has a factory set control location EXT1/EXT2 selection function. When digital input is active, the control location is EXT2 and PID is activated. Digital inputs 4 (DI4) and 5 (DI5) have factory set constant speed 1 and 2 functions. Constant speed 1 (par. 1202) is selected by activating digital input 4 (DI4) and constant speed 2 (par. 1203) by activating digital input 5 (DI5). ACH550-01 User's Manual Application macros and wiring 119 1 SCR Signal cable shield (screen) 2 AI1 External reference 1: 0(2)…10 V or 0(4)…20 mA 3 AGND Analogue input circuit common 4 10V Reference voltage +10 V DC 5 AI2 Actual signal 1: 0(2)…10 V or 0(4)…20 mA 2 6 AGND Analogue input circuit common 7 AO1 Output frequency: 0(4)…20 mA 8 AO2 Output current: 0(4)…20 mA 9 AGND Analogue output circuit common 10 24V Auxiliary voltage output +24 V DC 11 GND Common for DI return signals 12 DCOM Digital input common for all 13 DI1 Start/Stop: Activation starts the drive 14 DI2 EXT1/EXT2 selection: Activation takes PID in use 15 DI3 Setpoint selection: Set 1 / Set 2 16 DI4 Constant speed 1 (par. 1202) 1 17 DI5 Constant speed 2 (par. 1203) 1 18 DI6 Not used 19 RO1C Relay output 1 (par. 1401) Default operation Started => 19 connected to 21 20 RO1A 21 RO1B 22 RO2C Relay output 2 (par. 1402) Default operation Running => 22 connected to 24 23 RO2A 24 RO2B 25 RO3C Relay output 3 (par. 1403) Default operation Fault (-1) => 25 connected to 27 26 RO3A 27 RO3B 1 Not available if PID is activated 2 The sensor for AI2 is powered externally (not shown in the figure). See the manufacturer’s instructions. To use sensors supplied by the drive auxiliary voltage output, see page 124. Note: The drive starts only if possible protection functions (Run enable or Start enable 1 and 2) are activated from I/O or disabled wit