5X00152G01模块备件

5X00152G01

VP固件级别
（电子学
模块）
VP修订级别
（电子学
模块）固件功能
0F 9添加了对以下内容的支持：

使用图形从控制器进行校准。

将校准常数上传/下载到和
来自控制器。

新的调谐常数kServo和kServoDb to
替换硬编码常量。他们补充道：
灵活处理不同线圈
阻抗。
减少阀门校准时间。
0C 6增加了对VP冗余的支持。
0B 5是一个完整的生产固件版本。
0D过时
0E过时
0G 11冗余支持更改为多个
排除故障转移。
校准的改进。
修正了“线圈计数”的线圈诊断问题=
0”.
修正了滚动问题的位置反馈。
0H 13添加了“优先级需求”调整常数以支持
洛克波特项目。
修复PI数学中的溢出问题。
18 IPU-247
艾默生过程管理专有2C类
25-28页，25-9.3节“关机输入”，将名称更改为以下内容，然后添加文本
接下来是本节的结尾：
25-9.3停机输入（优先需求输入）
对于VP固件版本0H及更高版本，关机输入被重新定义为“优先级需求”
输入”。激活输入时，目标位置设置为可调常数。对于
与以前的固件版本兼容，priorityDemand的默认值为-5%。
这允许用户在翻转过程中快速将阀门移动到某个中间位置
条件用户可以灵活地创建自己的方案来处理烦恼。
当“优先需求输入”或“关机”输入激活时，VP处于本地模式
并且控制器必须无条件地跟踪需求反馈。
25-29页，25-10.5节，“开路线圈诊断错误”，替换“不正确”
二句加上：
已被调整以产生该结果。
25-29页，25-10.5节，“开路线圈诊断错误”，在一个之后添加以下文字
本节段：
对于0F之前的固件版本，诊断工作如下所述。以后
修正：测量伺服线圈电压，并与通过调整描述的模型进行比较
常数“kServo”和“kServoDb”。如果电压不适合模型，因为
太大，“开路线圈”被认为是错误的，并且设置了内部诊断位。那么时机呢
下面描述的序列用于将错误位发送到控制器。

5X00152G01

5X00152G01

VP Firmware Level (Electronics Module) VP Revision Level (Electronics Module) Firmware Features 0F 9 Added support for the following:
Calibration from the Controller using graphics.
Upload/download of calibration constants to and from the Controller.
New tuning constants kServo and kServoDb to replace hard-coded constants. They add flexibility in dealing with differing coil impedances.
Reduction of valve calibration time. 0C 6 Added support for VP Redundancy. 0B 5 First full production firmware release. 0D obsolete 0E obsolete 0G 11 Redundancy support changed so that multiple failovers are precluded. Improvements to calibration. Fixed problem with coil diagnostics for “coilCount = 0”. Position feedbacks rollover problem fixed. 0H 13 Added “priority Demand” tuning constant to support Rockport project. Fixed overflow problem in PI math. 18 IPU-247 Emerson Process Management Proprietary Class 2C Page 25-28, Section 25-9.3 “Shutdown Input”, change the name to the following, then add the text that follows to the end of the section: 25-9.3 Shutdown Input (Priority Demand Input) For VP firmware revisions 0H and later, the shutdown input is redefined to “Priority Demand Input”. When the input is activated, the target position is set to a tunable constant. For compatibility with previous firmware revisions, the default value of priorityDemand is -5%. This allows the user to rapidly move the valve to some intermediate position during upset conditions. The user has the flexibility to create his own scheme to handle an upset. While the “priority demand input”, or “Shutdown” input is active, the VP is in the local mode and the controller must unconditionally track demand feedback. Page 25-29, Section 25-10.5. “Open Coil Diagnostic Error”, replace “is incorrect” at the end of the second sentence with: has been adjusted to yield that result. Page 25-29, Section 25-10.5. “Open Coil Diagnostic Error”, add the following text after the first paragraph of the section: For firmware revisions prior to 0F, the diagnostic works as described below. For later revisions servo coil voltage is measured and compared to a model described by tuning constants “kServo” and “kServoDb’. If the voltage does not fit into the model, due to being too large, “open coil” is blamed and the internal diagnostic bit is set. Then the timing sequence described below is used to post the error bit to the controller.