5X00332G01模块备件

5X00332G01

定位器
卡片
登记
I/O通道
中的数字
点生成器R/W定义
IPU-247 21
艾默生过程管理专有2C类
第25-50页，将图25-10替换为以下内容：
线圈驱动+线圈驱动+
公共字段公共字段
COIL2+COIL2+
线圈1+线圈1+
线圈3+线圈3+
线圈驱动+
线圈2+
公共领域
公共字段公共字段
公共字段公共字段
世界
世界
世界
公共领域
公共领域
线圈1+
线圈3+
AC+AC+
公共字段公共字段
空调+
公共领域
0
0
0
0
0
0
0
0
LVDTALVDTA+
世界
LVDTA-LVDTALVDTA+LVDTA+
世界
LVDTBLVDTB+LVDTB+
LVDTB-LVDTBLVDTB+
公共领域
公共领域
公共领域
公共领域
Pmod（PVP）Emod（FVP）
C2+
C2-
C1+
C1-
C3+
C3-
伺服阀线圈
基本单元接线板
空调+
ACLA+
LALB+
LBLVDT
0
0
0
0
位置
反馈
解调器
A1、A2、B1，
B2、C1、C2
2.
3.
4.
笔记
B14
B15
B13
C
B
A.
LVRT
界面
1.所有现场接线必须在机柜入口点使用编织屏蔽和接地
推荐硬件（参考U3-1000和U3-1005中的“电缆指南”）。
2.端子B15、B14和B13上的负电压导致阀门打开。
3.该信号的幅度随着阀门打开而减小。
4.该信号的幅度随着阀门打开而增加。
5.节点A连接到端子AC+和LB+，
节点B连接到端子LB-和LA+，
节点C连接到端子AC-和LA-。
22 IPU-247
艾默生过程管理专有2C类
对第27节进行以下修改：
第27-5页，对表27-1进行以下更改：
注2后一行应改为：
“…（使用1C31204G03个性模块。）

5X00332G01

5X00332G01

Positioner Card Register I/O Channel Number in the Point Builder R/W Definition IPU-247 21 Emerson Process Management Proprietary Class 2C Page 25-50, Replace Figure 25-10 with the following: COIL-DRIVE+ COIL-DRIVE+ Field Common Field Common COIL2+ COIL2+ COIL1+ COIL1+ COIL3+ COIL3+ COIL-DRIVE+ COIL2+ Field Common Field Common Field Common Field Common Field Common Earth Earth Earth Field Common Field Common COIL1+ COIL3+ AC+ AC+ Field Common Field Common AC+ Field Common 0 0 0 0 0 0 0 0 LVDTALVDTA+ Earth LVDTA- LVDTALVDTA+ LVDTA+ Earth LVDTBLVDTB+ LVDTB+ LVDTB- LVDTBLVDTB+ Field Common Field Common Field Common Field Common Pmod (PVP) Emod (FVP) C2+ C2- C1+ C1- C3+ C3- Servo Valve Coils Base Unit Termination Block AC+ ACLA+ LALB+ LBLVDT 0 0 0 0 Position Feedback Demodulator A1, A2, B1, B2, C1, C2 2 3 4 Notes B14 B15 B13 C B A LVRT Interface 1. All field wiring must be braid-shielded and grounded at the entry point of the cabinet using the recommended hardware (refer to “Cable Guidelines” in U3-1000 and U3-1005). 2. Negative voltages on terminals B15, B14, and B13 cause the valve to open. 3. The amplitude of this signal decreases as the valve goes open. 4. The amplitude of this signal increases as the valve goes open. 5. Node A is connected to terminals AC+ and LB+, Node B is connected to terminals LB- and LA+, Node C is connected to terminals AC- and LA-. 22 IPU-247 Emerson Process Management Proprietary Class 2C Make the following Change to Section 27 Page 27-5, Make the following change toTable 27-1: The last line in Note 2 should be changed to read: “...(using 1C31204G03 Personality modules.)