1X00416H03模块备件

1X00416H03

本节讨论可能需要的某些硬件和软件任务
在将板安装到机箱中之前执行。
以产生所需配置并确保
MVME6100，您可能需要执行某些硬件修改
在安装模块之前。
MVME6100上的大多数选项是软件可配置的。配置
在电路板完成后，通过在控制寄存器中设置位来进行更改
安装在系统中。
跳线/开关用于控制非软件选项
可配置。这些跳线设置将在本节中进一步介绍
部分如果要将板跳线从其默认设置重置，
验证所有设置是否正确重置非常重要。
MVME6100制剂
图1-1说明了跳线、接头、连接器的位置，
MVME6100上的开关和各种其他组件
MVME6100上的几个手动可配置标头及其
设置如表1-2所示。每个标题的默认设置随附
在括号中。有关MVME6100上的引脚分配，请参阅5章，
引脚分配。
1-6计算机组文献中心网站
硬件准备和安装1
注：括号中的项目为出厂默认设置。
MVME6100经过工厂测试，并随配置一起出厂
如以下章节所述。
表1-2.MVME6100跳线和开关设置
跳线/
切换功能设置
J7 SCON接头[未安装跳线]
1-2
2-3
自动烤箱
总是斯科恩
不，斯科恩
J10，
J15–J18，
J25–J28
PMC/IPMC选择
标题
[已安装跳线]
1-2
[2-3]
PMC输入/输出
IPMC7xx的IPMC I/O
支持（默认）
J30前/后以太网和
转换模块选项
标题
请参阅前/后以太网和转换
1-9页的模块选项标题（J30），用于
细节。
S3 SROM配置开关，
集合板地理
住址
请参阅页的SROM配置开关（S3）
详情见1-10。
S4闪存启动存储体选择
配置开关，台
写保护A，写保护
B、 启动库选择，并安全
开始
请参阅闪存启动库选择配置
有关详细信息，请参见1-11页的开关（S4）。
MVME6100制剂
http://www.motorola.com/computer/literature 1-7
1.
图1-1.MVME6100布局
4296 0604
10/100/1000调试
ABT/RST
局域网1和局域网2
J42 J8
J30
J3
J19
J13和J14
J11和J12
J23和J24
J21和J22
P1
P2
PCI夹层卡PCI夹层卡
J4
U12
10/100/1000
J93
J9
J29 J7
PMC
IPMC
U32
S2
1 2 3 4 5 6 7 8 1 2 3 4
1 2 3 4 5 6 7 8
S4
S1和S3
1-8计算机组文献中心网站
硬件准备和安装1
SCON头（J7）
3引脚平面接头允许选择自动/启用/禁用SCON
VME配置。跨接脚1和2安装的跳线配置为：
SCON始终处于启用状态。跨引脚2和3安装的跳线配置：
对于禁用的SCON。未安装用于自动SCON的跳线配置。
PMC/IPMC选择头（J10、J15–J18、J25–J28）
九个3针平面接头用于PMC/IPMC模式I/O选择
插槽1.这九个接头也可以组合成一个接头
块分流器可用作跳线的块。
跨所有九个接头上的引脚1和引脚2安装的跳线选择PMC1
对于PMC I/O模式。跨接所有九个接头上的引脚2和3
选择IPMC I/O模式。

1X00416H03

1X00416H03
This section discusses certain hardware and software tasks that may need to be performed prior to installing the board in a chassis. To produce the desired configuration and ensure proper operation of the MVME6100, you may need to carry out certain hardware modifications before installing the module. Most options on the MVME6100 are software configurable. Configuration changes are made by setting bits in control registers after the board is installed in a system. Jumpers/switches are used to control those options that are not software configurable. These jumper settings are described further on in this section. If you are resetting the board jumpers from their default settings, it is important to verify that all settings are reset properly. MVME6100 Preparation Figure 1-1 illustrates the placement of the jumpers, headers, connectors, switches, and various other components on the MVME6100. There are several manually configurable headers on the MVME6100 and their settings are shown in Table 1-2. Each header’s default setting is enclosed in brackets. For pin assignments on the MVME6100, refer to Chapter 5, Pin Assignments. 1-6 Computer Group Literature Center Web Site Hardware Preparation and Installation 1 Note Items in brackets are factory default settings. The MVME6100 is factory tested and shipped with the configuration described in the following sections. Table 1-2. MVME6100 Jumper and Switch Settings Jumper/ Switch Function Settings J7 SCON Header [No jumper installed] 1-2 2-3 Auto-SCON Always SCON No SCON J10, J15–J18, J25–J28 PMC/IPMC Selection Headers [Jumper installed] 1-2 [2-3] PMC I/O IPMC I/O for IPMC7xx support (default) J30 Front/Rear Ethernet and Transition Module Options Header Refer to Front/Rear Ethernet and Transition Module Options Header (J30) on page 1-9 for details. S3 SROM Configuration Switch, sets board Geographical Address Refer to SROM Configuration Switch (S3) on page 1-10 for details. S4 Flash Boot Bank Select Configuration Switch, sets Write Protect A, Write Protect B, Boot Bank Select, and Safe Start Refer to Flash Boot Bank Select Configuration Switch (S4) on page 1-11 for details. MVME6100 Preparation http://www.motorola.com/computer/literature 1-7 1 Figure 1-1. MVME6100 Layout 4296 0604 10/100/1000 DEBUG ABT/RST LAN 1 LAN 2 J42 J8 J30 J3 J19 J13 J14 J11 J12 J23 J24 J21 J22 P1 P2 PCI MEZZANINE CARD PCI MEZZANINE CARD J4 U12 10/100/1000 J93 J9 J29 J7 PMC IPMC U32 S2 1 2 3 4 5 6 7 8 1 2 3 4 1 2 3 4 5 6 7 8 S4 S1 S3 1-8 Computer Group Literature Center Web Site Hardware Preparation and Installation 1 SCON Header (J7) A 3-pin planar header allows the choice for auto/enable/disable SCON VME configuration. A jumper installed across pins 1 and 2 configures for SCON always enabled. A jumper installed across pins 2 and 3 configures for SCON disabled. No jumper installed configures for auto SCON. PMC/IPMC Selection Headers (J10, J15 – J18, J25 – J28) Nine 3-pin planar headers are for PMC/IPMC mode I/O selection for PMC slot 1. These nine headers can also be combined into one single header block where a block shunt can be used as a jumper. A jumper installed across pins 1 and 2 on all nine headers selects PMC1 for PMC I/O mode. A jumper across pins 2 and 3 on all nine headers selects IPMC I/O mode.