1X00480G04模块备件

1X00480G04

6.同时向内移动喷油器/推料器操纵杆。
7.验证MVME6100是否正确就位，并将其固定到
底盘，使用靠近喷油器/喷射器的两个螺钉
杠杆。
8.将适当的电缆连接到MVME6100。
要从机箱中卸下板，请按下红色锁舌（IEEE
仅处理）并反转过程。
与外围设备的连接
将MVME6100安装在机箱中后，即可连接
外围设备，并向电路板供电。
1-14计算机组文献中心网站
硬件准备和安装1
1-7页的图1-1显示了各种连接器的位置，同时
表1-5为您列出了它们。请参阅5章，引脚分配以了解
下面列出的连接器的引脚分配。
完成安装
确认硬件已安装，电源/外围电缆已连接
适合您的系统配置。
更换机箱或系统盖，将系统重新连接到AC或DC
电源，并打开设备电源。
表1-5.MVME6100连接器
连接器功能
J3 IPMC761/712连接器
J4 PMC扩展连接器
J9、J93千兆以太网连接器
J11、J12、J13、J14 PCI夹层卡（PMC）插槽1连接器
J19 COM1连接器
J21、J22、J23、J24 PCI夹层卡（PMC）插槽2连接器
J29 COM2平面连接器
P1、P2 VME后面板连接器
2-1
2启动和运行
介绍
本章为您提供以下信息：
❏ 通电程序
❏ 开关和指示器
施加功率
验证所有必要的硬件准备工作是否完成，以及
所有连接都正确，您可以向系统通电。
当您准备向MVME6100供电时：
❏ 验证机箱电源电压设置是否与匹配
使用国家/地区的电压（如果
系统未自动感应）
❏ 通电后，MVME6100启动MOTLoad
提示，MVME6100>
开关和指示器
MVME6100板提供了一个单按钮开关，可提供：
中止和复位（ABT/RST）功能。按下开关时
在不到三秒的时间内，处理器将生成中止中断。
如果开关保持三秒钟以上，则电路板硬复位
生成。板硬复位将复位MPC7457、MV64360和MV64360，
Tsi148 VME桥接ASIC、PCI6520、PMC1/2插槽，均为以太网PHY，
串行端口、PMCspan插槽、两个闪存组和设备总线控制
PLD。如果VME系统控制器启用了MVME6100，则VME
总线将被复位，本地复位输入被发送到Tsi148 VME控制器

1X00480G04

1X00480G04

6. Simultaneously move the injector/ejector levers in an inward direction. 7. Verify that the MVME6100 is properly seated and secure it to the chassis using the two screws located adjacent to the injector/ejector levers. 8. Connect the appropriate cables to the MVME6100. To remove the board from the chassis, press the red locking tabs (IEEE handles only) and reverse the procedure. Connection to Peripherals When the MVME6100 is installed in a chassis, you are ready to connect peripherals and apply power to the board. 1-14 Computer Group Literature Center Web Site Hardware Preparation and Installation 1 Figure 1-1 on page 1-7 shows the locations of the various connectors while Table 1-5 lists them for you. Refer to Chapter 5, Pin Assignments for the pin assignments of the connectors listed below. Completing the Installation Verify that hardware is installed and the power/peripheral cables connected are appropriate for your system configuration. Replace the chassis or system cover, reconnect the system to the AC or DC power source, and turn the equipment power on. Table 1-5. MVME6100 Connectors Connector Function J3 IPMC761/712 connector J4 PMC expansion connector J9, J93 Gigabit Ethernet connectors J11, J12, J13, J14 PCI mezzanine card (PMC) slot 1 connector J19 COM1 connector J21, J22, J23, J24 PCI mezzanine card (PMC) slot 2 connector J29 COM2 planar connector P1, P2 VME rear panel connectors 2-1 2 2Startup and Operation Introduction This chapter gives you information about the: ❏ Power-up procedure ❏ Switches and indicators Applying Power After you verify that all necessary hardware preparation is complete and all connections are made correctly, you can apply power to the system. When you are ready to apply power to the MVME6100: ❏ Verify that the chassis power supply voltage setting matches the voltage present in the country of use (if the power supply in your system is not auto-sensing) ❏ On powering up, the MVME6100 brings up the MOTLoad prompt, MVME6100> Switches and Indicators The MVME6100 board provides a single pushbutton switch that provides both abort and reset (ABT/RST) functions. When the switch is depressed for less than three seconds, an abort interrupt is generated to the processor. If the switch is held for more than three seconds, a board hard reset is generated. The board hard reset will reset the MPC7457, MV64360, Tsi148 VME Bridge ASIC, PCI6520, PMC1/2 slots, both Ethernet PHYs, serial ports, PMCspan slot, both flash banks, and the device bus control PLD. If the MVME6100 is enabled for VME system controller, the VME bus will be reset and local reset input is sent to the Tsi148 VME controller