KJ4001X1-CE1模块备件

KJ4001X1-CE1

从工厂发货时，MVME6100具有以下VME
通过全局环境变量（GEV）编程的配置，用于
Tsi148 VME控制器。固件允许某些VME设置：
以便用户定制环境。这个
以下是可更改的默认VME设置的说明
由用户提供。有关更多信息，请参阅MOTLoad用户手册
附录C中列出的Tundra的Tsi148用户手册
文档
❏ MVME6100>vmeCfg–s–m
显示选定的默认VME设置
-解释如下：
VME PCI主机启用[Y/N]=Y
MVME6100>
PCI主机已启用。
❏ MVME6100>vmeCfg–s–r234
显示选定的默认VME设置
-解释如下：
VMEbus主控制寄存器=0000000 3
MVME6100>
VMEbus主控制寄存器设置为默认值
（复位）状态。
❏ MVME6100>vmeCfg–s–r238
显示选定的默认VME设置
-解释如下：
VMEbus控制寄存器=0000000 8
MVME6100>
VMEbus控制寄存器设置为2048的全局超时
µ秒。
❏ MVME6100>vmeCfg–s–r414
显示选定的默认VME设置
-解释如下：
CRG属性寄存器=00000000
CRG基址上部寄存器=00000000
默认VME设置
http://www.motorola.com/computer/literature 3-13
3.
CRG基址下寄存器=00000000
MVME6100>
CRG属性寄存器设置为默认值（重置）
条件
❏ MVME6100>vmeCfg–s–i0
显示选定的默认VME设置
-解释如下：
入站图像0属性寄存器=000227AF
入站图像0起始地址上部寄存器=00000000
入站映像0起始地址较低寄存器=00000000
入站图像0结束地址上部寄存器=00000000
入站图像0结束地址较低寄存器=1FF0000
入站图像0平移偏移量上限寄存器=00000000
入站图像0平移偏移量下寄存器=00000000
MVME6100>
未启用入站窗口0（ITAT0）；256处的虚拟FIFO
字节，SST320处的2eSST定时，响应于2eSST，2eVME，
MBLT和BLT周期，A32地址空间，响应监控器，
用户、程序和数据周期。图像从0x00000000映射到
VMbus上的0x1FF0000，将1x1转换为PCI-X总线（因此
1x1到本地存储器）。要启用此窗口，请将ITAT0的第31位设置为
至1。
注：对于入站翻译，上翻译偏移量
寄存器需要设置为0xFFFFFF以确保正确
转换到PCI-X本地总线。
❏ MVME6100>vmeCfg–s–o1
显示选定的默认VME设置
-解释如下：
出站图像1属性寄存器=80001462
出站映像1起始地址上部寄存器=00000000
出站映像1起始地址较低寄存器=91000000
出站图像1结束地址上部寄存器=00000000
出站图像1结束地址下部寄存器=AFFF0000
出站图像1转换偏移量上限寄存器=00000000
出站图像1平移偏移较低寄存器=7000000
出站图像1 2 SST广播选择寄存器=00000000

KJ4001X1-CE1

KJ4001X1-CE1

As shipped from the factory, the MVME6100 has the following VME configuration programmed via Global Environment Variables (GEVs) for the Tsi148 VME controller. The firmware allows certain VME settings to be changed in order for the user to customize the environment. The following is a description of the default VME settings that are changeable by the user. For more information, refer to the MOTLoad User’s Manual and Tundra’s Tsi148 User Manual, listed in Appendix C, Related Documentation. ❏ MVME6100> vmeCfg –s –m Displaying the selected Default VME Setting - interpreted as follows: VME PCI Master Enable [Y/N] = Y MVME6100> The PCI Master is enabled. ❏ MVME6100> vmeCfg –s –r234 Displaying the selected Default VME Setting - interpreted as follows: VMEbus Master Control Register = 00000003 MVME6100> The VMEbus Master Control Register is set to the default (RESET) condition. ❏ MVME6100> vmeCfg –s –r238 Displaying the selected Default VME Setting - interpreted as follows: VMEbus Control Register = 00000008 MVME6100> The VMEbus Control Register is set to a Global Timeout of 2048 µseconds. ❏ MVME6100> vmeCfg –s –r414 Displaying the selected Default VME Setting - interpreted as follows: CRG Attribute Register = 00000000 CRG Base Address Upper Register = 00000000 Default VME Settings http://www.motorola.com/computer/literature 3-13 3 CRG Base Address Lower Register = 00000000 MVME6100> The CRG Attribute Register is set to the default (RESET) condition. ❏ MVME6100> vmeCfg –s –i0 Displaying the selected Default VME Setting - interpreted as follows: Inbound Image 0 Attribute Register = 000227AF Inbound Image 0 Starting Address Upper Register = 00000000 Inbound Image 0 Starting Address Lower Register = 00000000 Inbound Image 0 Ending Address Upper Register = 00000000 Inbound Image 0 Ending Address Lower Register = 1FFF0000 Inbound Image 0 Translation Offset Upper Register = 00000000 Inbound Image 0 Translation Offset Lower Register = 00000000 MVME6100> Inbound window 0 (ITAT0) is not enabled; Virtual FIFO at 256 bytes, 2eSST timing at SST320, respond to 2eSST, 2eVME, MBLT, and BLT cycles, A32 address space, respond to Supervisor, User, Program, and Data cycles. Image maps from 0x00000000 to 0x1FFF0000 on the VMbus, translates 1x1 to the PCI-X bus (thus 1x1 to local memory). To enable this window, set bit 31 of ITAT0 to 1. Note For Inbound Translations, the Upper Translation Offset Register needs to be set to 0xFFFFFFFF to ensure proper translations to the PCI-X Local Bus. ❏ MVME6100> vmeCfg –s –o1 Displaying the selected Default VME Setting - interpreted as follows: Outbound Image 1 Attribute Register = 80001462 Outbound Image 1 Starting Address Upper Register = 00000000 Outbound Image 1 Starting Address Lower Register = 91000000 Outbound Image 1 Ending Address Upper Register = 00000000 Outbound Image 1 Ending Address Lower Register = AFFF0000 Outbound Image 1 Translation Offset Upper Register = 00000000 Outbound Image 1 Translation Offset Lower Register = 70000000 Outbound Image 1 2eSST Broadcast Select Register = 00000000