KJ3204X1-BA1模块备件

KJ3204X1-BA1

出站窗口3（OTAT3）已启用，2在
SST320，SCT传输模式，A16/D32监控访问。这个
窗口接受PCI-X本地总线上的传输
0xB3FF0000-0xB3FF0000，并将其转换到VMEbus
使用偏移量0x4C000000，因此可以访问
PCI-X本地总线成为对上的0xFFFF0000的访问
VMEbus。
❏ MVME6100>vmeCfg–s–o7
显示选定的默认VME设置
-解释如下：
出站图像7属性寄存器=80001065
出站图像7起始地址上部寄存器=00000000
出站映像7起始地址较低寄存器=B1000000
出站图像7结束地址上部寄存器=00000000
出站图像7结束地址下部寄存器=B1FF0000
出站图像7平移偏移量上限寄存器=00000000
出站图像7平移偏移较低寄存器=4F000000
出站图像7 2EST广播选择寄存器=00000000
MVME6100>
出站窗口7（OTAT7）已启用，2在
SST320，SCT的传输模式，CR/CSR监控访问。这个
窗口接受PCI-X本地总线上的传输
0xB1000000-0xB1FF0000并将其转换到VMEbus
使用偏移量0x4F000000，因此可以访问
PCI-X本地总线成为对上的0x00000000的访问
VMEbus。
3-16计算机组文献中心网站
非负载固件
3.
固件设置
以下各节提供了与
MVME6100的VME固件设置
由硬件跳线控制，而大多数VME设置为：
由固件命令实用程序vmeCfg管理。
CR/CSR设置
CR/CSR基址根据以下条件初始化为适当的设置：
地理地址；即VME时隙号。参见VME64
有关详细信息，请参阅规范和VME64扩展。结果，512K
可以使用CR/CSR从VMEbus访问字节CR/CSR区域
AM代码。
显示VME设置
要显示可变VME设置，请在固件中键入以下内容

KJ3204X1-BA1

KJ3204X1-BA1

Outbound window 3 (OTAT3) is enabled, 2eSST timing at SST320, transfer mode of SCT, A16/D32 Supervisory access. The window accepts transfers on the PCI-X Local Bus from 0xB3FF0000-0xB3FF0000 and translates them onto the VMEbus using an offset of 0x4C000000, thus an access to 0xB3FF0000 on the PCI-X Local Bus becomes an access to 0xFFFF0000 on the VMEbus. ❏ MVME6100> vmeCfg –s –o7 Displaying the selected Default VME Setting - interpreted as follows: Outbound Image 7 Attribute Register = 80001065 Outbound Image 7 Starting Address Upper Register = 00000000 Outbound Image 7 Starting Address Lower Register = B1000000 Outbound Image 7 Ending Address Upper Register = 00000000 Outbound Image 7 Ending Address Lower Register = B1FF0000 Outbound Image 7 Translation Offset Upper Register = 00000000 Outbound Image 7 Translation Offset Lower Register = 4F000000 Outbound Image 7 2eSST Broadcast Select Register = 00000000 MVME6100> Outbound window 7 (OTAT7) is enabled, 2eSST timing at SST320, transfer mode of SCT, CR/CSR Supervisory access. The window accepts transfers on the PCI-X Local Bus from 0xB1000000-0xB1FF0000 and translates them onto the VMEbus using an offset of 0x4F000000, thus an access to 0xB1000000 on the PCI-X Local Bus becomes an access to 0x00000000 on the VMEbus. 3-16 Computer Group Literature Center Web Site MOTLoad Firmware 3 Firmware Settings The following sections provide additional information pertaining to the VME firmware settings of the MVME6100. A few VME settings are controlled by hardware jumpers while the majority of the VME settings are managed by the firmware command utility vmeCfg. CR/CSR Settings The CR/CSR base address is initialized to the appropriate setting based on the Geographical address; that is, the VME slot number. See the VME64 Specification and the VME64 Extensions for details. As a result, a 512K byte CR/CSR area can be accessed from the VMEbus using the CR/CSR AM code. Displaying VME Settings To display the changeable VME setting, type the following at the firmware