KJ4001X1-BB1模块备件

KJ4001X1-BB1

16通道、4至20 mA、HART的AI（Plus）卡规范
信道数16
输入传感器类型4至20 mA（跨度），双线
全信号范围2至22 mA，带超范围检查
20 mA时变送器功率小为13.5 V（大电流限制为29 mA）
温度范围内的精度：量程的0.2%
重复性：量程的0.05%
分辨率16位A/D转换器
滚降频率（抗混叠）-2.7 Hz时为3 dB-20 Hz时为20.5 dB
校准：无需
单板卡的本地总线电流（标称12V直流电）：典型85 mA，大150 mA
冗余：典型110 mA，大200 mA
24V直流（+/-10%）条件下，每个卡的现场电路功率大为500mA
隔离：每个通道与系统光学隔离
并在1000V DC下进行工厂测试。
HART通信支持AMS设备管理器的HART直通。
控制功能的HART变量和状态报告。
每个启用通道的Hart扫描时间为600–800 mS（典型）
冗余AI Plus卡的简化电路和连接图，16通道，4至20 mA，HART。
DeltaV M系列传统I/O，2022年8月
www.emerson。com/deltav 7
8通道RTD输入卡规范
每个卡的RTD通道8
传感器类型2线、3线或4线
传感器配置电阻，Pt100、Pt200、Pt500、Ni120、Cu10，用户定义
满标度信号范围见下表
精度见下表
重复性：量程的0.05%
A/D分辨率16位
校准：无需
单位：摄氏度，华氏度
传感器励磁电流100µA
50/60 Hz下的共模抑制120 dB
共模阻抗>10兆欧
本地总线电流（12V直流标称）160 mA
打开传感器检测时间1秒
开路中压导线检测时间15秒
电阻式温度检测器，欧姆传感器类型规格
传感器
类型
满的
规模
操作
范围
25°C
参考精度
温度
漂流
决议
电阻0至2000Ω0至2000欧姆±6.2Ω±0.112Ω/°C~0.02Ω
Pt100-200至850°C-200至85°C±0.5°C±1.018°C/°C~0.05°C
Pt200-200至850°C-200至850℃±0.5°C±0.012°C/°C~0.05°C
Pt500-200至850°C-200至85°C±3.5°C±0.063°C/°C~0.18°C
Ni120-70至300°C 70至300℃±0.2°C±0.006°C/℃C~0.02°C
Cu10-30至140℃-30至40℃±2.0℃±0.157℃/°C~0.23℃
用户定义*0至1000Ω0至1000欧姆±0.4Ω±0.009Ω/°C~0.05Ω
*Callendar-Van Dusen线性化方程可用于用户定义的Pt RTD。有关使用信息，请参阅DeltaV联机丛书中推荐的I/O实践。
RTD输入卡的简化电路图，8通道。
DeltaV M系列传统I/O，2022年8月
www.emerson。com/deltav 8
8通道热电偶/mV输入卡规范
每卡8个频道
传感器类型：热电偶mV B、E、J、K、N、R、S、T，无特征
低电平电压源
传感器范围见下一页的表
重复性：量程的0.05%
A/D分辨率16位
校准：无需
单位：摄氏度，华氏度
冷端补偿
（中压信道不可用）
本地：整体安装在接线盒中
外部：将一个通道配置为外部冷接点
剩余输入的补偿
隔离：每个通道与系统光学隔离，以及
工厂测试至1500V直流。
通道1、2、3和4与通道5、6、7隔离，
和8（通过1500V直流工厂试验验证）。
连接到通道1、2、3和4的热电偶
未进行电气隔离，且应在+0.7V DC范围内
彼此的。
连接到通道5、6、7和8的热电偶
未进行电气隔离，且应在+0.7V DC范围内
彼此的。
DC/50/60 Hz下的共模抑制120 dB
共模阻抗>10兆欧

KJ4001X1-BB1

KJ4001X1-BB1
Specifications for AI (Plus) Card, 16-channel, 4 to 20 mA, HART Number of Channels 16 Input Sensor Types 4 to 20 mA (span), 2-wire Full Signal Range 2 to 22 mA, with over range checking Transmitter Power 13.5 V minimum at 20 mA (max current limited at 29 mA) Accuracy Over Temperature Range 0.2% of span Repeatability 0.05% of span Resolution 16-bit A/D converter Roll-off Frequency (Anti-aliasing) -3 dB at 2.7 Hz; -20.5 dB at 20 Hz Calibration None required Local Bus Current per Card (12V DC nominal) Simplex: 85 mA typical, 150 mA maximum Redundant: 110 mA typical, 200 mA maximum Field Circuit Power per Card 500 mA maximum @ 24V DC (+/-10%) Isolation Each channel is optically isolated from the system and factory tested to 1000V DC. HART Communications Support HART pass-through for AMS Device Manager. HART variable and status reporting for control functions. Hart Scan Time 600 – 800 mS (typical) per enabled channel Simplified circuit and connection diagram for redundant AI Plus card, 16-channel, 4 to 20 mA, HART. DeltaV M-series Traditional I/O August 2022 www.emerson.com/deltav 7 Specifications for RTD Input Card, 8-channel RTD Channels per Card Eight Sensor Types 2 wire, 3 wire, or 4 wire Sensor Configuration Resistance, Pt100, Pt200, Pt500, Ni120, Cu10, User Defined Full Scale Signal Range See Table below Accuracy See Table below Repeatability 0.05% of span A/D Resolution 16-bit Calibration None required Units °C, °F Sensor Excitation Current 100 µA Common Mode Rejection 120 dB at 50/60 Hz Common Mode Impedance > 10 mega ohms LocalBus Current (12V DC nominal) 160 mA Open Sensor Detection Time 1 second Open mV Lead Detection Time 15 seconds RTD, ohms Sensor Type Specifications Sensor Type Full Scale Operating Range 25°C Reference Accuracy Temperature Drift Resolution Resistance 0 to 2,000 Ω 0 to 2,000 Ω ± 6.2 Ω ± 0.112 Ω/°C ~0.02 Ω Pt100 -200 to 850°C -200 to 850°C ± 0.5°C ± 0.018°C/°C ~0.05°C Pt200 -200 to 850°C -200 to 850°C ± 0.5°C ± 0.012°C/°C ~0.05°C Pt500 -200 to 850°C -200 to 850°C ± 3.5°C ± 0.063°C/°C ~0.18°C Ni120 -70 to 300°C 70 to 300°C ± 0.2°C ± 0.006°C/°C ~0.02°C Cu10 -30 to 140°C -30 to 140°C ± 2.0°C ± 0.157°C/°C ~0.23°C User Defined* 0 to 1000 Ω 0 to 1000 Ω ± 0.4 Ω ± 0.009 Ω/°C ~0.05 Ω *The Callendar-Van Dusen linearization equation can be used with user defined Pt RTDs. Refer to Recommended I/O Practices in DeltaV Books online for usage information. Simplified circuit diagram for RTD Input card, 8 channels. DeltaV M-series Traditional I/O August 2022 www.emerson.com/deltav 8 Specifications for Thermocouple/mV Input Card, 8-channel Channels per Card Eight Sensor Types Thermocouple mV B, E, J, K, N, R, S, T, uncharacterized Low level voltage source Sensor Ranges See table next page Repeatability 0.05% of span A/D Resolution 16-bit Calibration None required Units °C, °F Cold Junction Compensation (Not available on mV channels) Local: Integrally mounted in terminal block External: Configure one channel as external cold junction compensation for remaining inputs Isolation Each channel is optically isolated from the system and factory tested to 1500V DC. Channels 1, 2, 3, and 4 are isolated from channels 5, 6, 7, and 8 (verified by 1500V DC factory test). Thermocouples attached to channels 1, 2, 3, and 4 are not electrically isolated and should be within + 0.7V DC of each other. Thermocouples attached to channels 5, 6, 7, and 8 are not electrically isolated and should be within + 0.7V DC of each other. Common Mode Rejection 120 dB at DC/50/60 Hz Common Mode Impedance > 10 mega ohms