KJ3242X1-EA1模块备件

KJ3242X1-EA1

I/O卡I/O
卡片键控
传统I/O
接线端子
大量接线板
DO，8通道，24V直流，隔离B5输入/输出端子板
熔断接线板
16引脚质量接线板
DO Plus，32通道，24V直流高压侧B4 32通道DO端子
系列2 Plus的块
冗余32通道
DO端子排
系列2 Plus
40针DO
大规模终止
系列2 Plus的块
冗余40引脚DO
大规模终止
系列2 Plus的块
DI，8通道，120V交流，干触点E1输入/输出端子板
熔断接线板
NA
DI，8通道，120V交流，隔离E4输入/输出端子板
熔断接线板
NA
DO，8通道，120V AC/230V AC，高端F1输入/输出端子板
熔断接线板
NA
DO，8通道，120V AC/230V AC，隔离F4输入/输出端子板
熔断接线板
NA
系统兼容性
M系列传统I/O硬件需要：
MQ、MX或PK控制器。
„M系列水平或垂直加载器。
S系列和M系列控制器可以安装在同一个控制器上
v11.3.1及更高版本中的DeltaV区域控制网络。
控制模块可以分配给任何控制器，并且
完全支持控制器间引用。
以下传统I/O Plus卡需要v13.3.1
或更高软件：
„AI Plus，4-20 mA HART，16通道。
„AO Plus，4-20 mA HART，16通道。
„DI Plus，32通道，24V直流干触点。
„DO Plus，32通道，24V直流高压侧。
终端故障检测是一项仅起作用的功能
在以下卡中：
„DI Plus，32通道，24V直流干触点。
„DO Plus，32通道，24V直流高压侧。
与冗余40引脚质量DI或DO一起使用时
与M系列质量组合的接线盒
连接解决方案或P+F HiD或HiC IS屏障
以及用于DeltaV DCS的终端板。
所有其他经批准的三方批量终端产品可能：
可与非Plus S系列和M系列I/O接口一起使用。
M系列传统I/O水平载波在物理上不是
与S系列水平控制器托架兼容。
使用M系列控制器安装M系列I/O接口
以及与S系列控制器的S系列I/O接口。
DeltaV M系列传统I/O，2022年8月
www.emerson。com/deltav 30
所获证书
以下认证适用于M系列：
传统I/O（请参阅实际证书以了解确切的证书
对于每种产品）：
„CE
EMC:EN 61326-1
„调频
FM 3600
FM 3611
„CSA
CSA C22.2213号
CSA C22.21010-1号
„ATEX
EN60079-0
IEC60079-7
EN60079-15
„IEC Ex
IEC60079-0
IEC60079-7
IEC60079-15
„海事认证：IACS E10
ABS设计评估证书
DNV海事证书
危险区域/位置
可以安装和使用M系列传统I/O卡
基于以下标准（见实际证书
对于每个产品的准确产品标记）：
„FM（美国）
一类，二类，A、B、C、D、T4组
„cFM（加拿大）
一类，二类，A、B、C、D、T4组
„ATEX
II 3G Ex ec IIC T4 Gc
II 3G Ex ec[ic]IIC T4 Gc
II 3G Ex nA nC IIC T4 Gc
„IEC Ex
II 3G Ex ec IIC T4 Gc
II 3G Ex ec ic IIC T4 Gc
II 3G Ex nA nC IIC T4 Gc
关于安装说明，请参考以下文件：
DeltaV M系列12P12931类2部分安装说明
2区安装说明DeltaV M系列12P204
DI Plus，32通道，24V直流，
干接触
E3 32信道DI
系列2 Plus的接线盒
冗余32通道DI
系列2 Plus的接线盒
40引脚DI质量
系列2 Plus的接线盒
冗余40引脚DI质量
系列2 Plus的接线盒
PCI，4通道C6 32通道接线板NA
SOE，16通道，24V直流C5 32通道接线板，40引脚质量接线板
DO，8通道，24V直流，高压侧B6输入/输出端子板
熔断接线板
10引脚质量接线板
16引脚质量终端块通道，120/230V交流，高压侧。
DeltaV M系列传统I/O，2022年8月
www.emerson。com/deltav 27
I/O接线板
可提供各种I/O端子块，以满足特定要求
功能和环境要求
安装I/O接口是I/O卡的组合
以及I/O端子块。每个I/O接口都有的键控
使得一旦安装在具有端子块的载体槽中，
该接线板将仅接受替换卡。
8通道标准接线盒。
键控机构由两个旋转的键控柱组成
并锁定在接线盒底座中。每个职位有6个职位：
A-F和1-6。每张卡都分配了一个的密钥，并标记
在I/O卡的一侧：
终端块键控示例。
键可防止安装不正确的卡，并且
卡上的图形信息便于确定
如果钥匙槽将接受特定卡。
有不同的I/O端子块可用于满足
现场信号的布线需求。
„8通道接线盒
„熔断8通道接线盒
„AI 8通道接线盒
„2线AI加16通道接线板
„4线AI加16通道接线板
„AO加16信道

KJ3242X1-EA1

KJ3242X1-EA1

I/O Card I/O
Card Keying
Traditional I/O
Terminal Blocks
Mass Termination Blocks
DO, 8-Channel, 24V DC, Isolated B5 I/O terminal block
Fused terminal block
16-pin Mass termination block
DO Plus, 32-Channel, 24V DC High-Side B4 32-Channel DO terminal
block for Series 2 Plus
Redundant 32-Channel
DO terminal block for
Series 2 Plus
40-pin DO
Mass termination
block for Series 2 Plus
Redundant 40-pin DO
Mass termination
block for Series 2 Plus
DI, 8-Channel, 120V AC, Dry Contact E1 I/O terminal block
Fused terminal block
NA
DI, 8-Channel, 120V AC, Isolated E4 I/O terminal block
Fused terminal block
NA
DO, 8-Channel, 120V AC/ 230V AC, High-Side F1 I/O terminal block
Fused terminal block
NA
DO, 8-Channel, 120V AC/ 230V AC, Isolated F4 I/O terminal block
Fused terminal block
NA
System Compatibility
M-series traditional I/O hardware requires:
„ MQ, MX or PK controllers.
„ M-series horizontal or VerticalPlus carriers.
S-series and M-series controllers can be installed on the same
DeltaV Area Control Network in v11.3.1 and beyond.
Control modules can be assigned to any controller and
inter-controller references are fully supported.
The following traditional I/O Plus cards require v13.3.1
or higher Software:
„ AI Plus, 4-20 mA HART, 16 Channels.
„ AO Plus, 4-20 mA HART, 16 Channels.
„ DI Plus, 32-channel, 24V DC Dry contact.
„ DO Plus, 32-channel, 24V DC High-Side.
Termination Fault Detection is a feature that only works
within the following cards:
„ DI Plus, 32-channel, 24V DC Dry contact.
„ DO Plus, 32-channel, 24V DC High-Side.
when used with the redundant 40-pin Mass DI or DO
Terminal Block combined with the M-series Mass
Connection Solutions or P+F HiD or HiC IS barriers
and termination boards for DeltaV DCS.
All other approved third party mass termination products may
be used with both non Plus S-series and M-series I/O interfaces.
M-series traditional I/O horizontal carriers are not physically
compatible with S-series horizontal controller carriers.
Install M-series I/O interfaces with M-series controllers
and S-series I/O interfaces with S-series controllers.
DeltaV M-series Traditional I/O August 2022
www.emerson.com/deltav 30
Certifications
The following certifications are available for M-series
Traditional I/O (see actual certificates for exact certifications
for each product):
„ CE
EMC: EN 61326-1
„ FM
FM 3600
FM 3611
„ CSA
CSA C22.2 No. 213
CSA C22.2 No. 1010-1
„ ATEX
EN60079-0
IEC60079-7
EN60079-15
„ IEC-Ex
IEC60079-0
IEC60079-7
IEC60079-15
„ Marine Certifications: IACS E10
ABS Certificate of Design Assessment
DNV Marine Certificate
Hazardous Area/Location
M-series Traditional I/O Cards can be installed and used
based on the following standards (see actual certificates
for exact product markings for each product):
„ FM (USA)
Class I, Division 2, Groups A, B, C, D, T4
„ cFM (Canada)
Class I, Division 2, Groups A, B, C, D, T4
„ ATEX
II 3G Ex ec IIC T4 Gc
II 3G Ex ec [ic] IIC T4 Gc
II 3G Ex nA nC IIC T4 Gc
„ IEC-Ex
II 3G Ex ec IIC T4 Gc
II 3G Ex ec ic IIC T4 Gc
II 3G Ex nA nC IIC T4 Gc
Regarding the Installation instructions please refer to the following Documents:
Class 1 Division 2 Installation Instructions DeltaV M-series 12P1293
Zone 2 Installation Instructions DeltaV M-series 12P204
DI Plus, 32-Channel, 24V DC,
Dry Contact
E3 32-Channel DI
terminal block for Series 2 Plus
Redundant 32-Channel DI
terminal block for Series 2 Plus
40-pin DI Mass
termination block for Series 2 Plus
Redundant 40-pin DI Mass
termination block for Series 2 Plus
PCI, 4-Channel C6 32-Channel terminal block NA
SOE, 16-Channel, 24V DC C5 32-Channel terminal block 40-pin Mass termination block
DO, 8-Channel, 24V DC, High-Side B6 I/O terminal block
Fused terminal block
10-pin Mass termination block
16-pin Mass termination blockchannel,120/230V AC, High-Side.
DeltaV M-series Traditional I/O August 2022
www.emerson.com/deltav 27
I/O Terminal Blocks
A variety of I/O terminal blocks are available to meet specific
functionality and environmental requirements of the
installation. The I/O interface is a combination of the I/O card
and the I/O terminal block. Each I/O interface is uniquely keyed
so that once installed in a carrier slot with a terminal block,
that terminal block will only accept a replacement card.
8-channel standard terminal block.
The keying mechanism consists of two keying posts that rotate
and lock into the terminal block base. Each post has 6 positions:
A-F and 1-6. Each card is assigned a unique key, which is marked
on the side of the I/O card:
Terminal block keying example.
The keys prevent installation of an incorrect card, and the
graphical information on the card makes it easy to determine
if a keyed slot will accept a particular card.
There are different I/O terminal blocks available to meet the
wiring needs of field signals.
„ 8-Channel terminal block
„ Fused 8-Channel terminal block
„ AI 8-Channel terminal block
„ 2-wire AI Plus 16-Channel terminal block
„ 4-wire AI Plus 16-Channel terminal block
„ AO Plus 16-Channel terminal block
„ DI 32-Channel terminal block
„ DI Plus 32-Channel terminal block
„ DO Plus 32-Channel terminal block
„ Isolated Input terminal block
„ RTD/Resistance terminal block
„ Thermocouple terminal block
The following redundant I/O terminal blocks are available
on some I/O interfaces, allowing a pair of cards to be installed
as a redundant pair.
„ Redundant AI 8-Channel terminal block
„ Redundant AI Plus 16-Channel terminal block
„ Redundant AO 8-Channel terminal block
„ Redundant AO Plus 16-Channel terminal block
„ Redundant Discrete 8-Channel terminal block
„ Redundant DI Plus 32-Channel terminal block
„ Redundant DO Plus 32-Channel terminal block
The table on the following page lists the compatible
terminal blocks for each card, along with the cards
unique key positions. The first terminal block listed
is the recommended terminal block.
In addition to standard signal wiring, some cards may also
be ordered with Mass Terminal blocks that allow these cards
to be connected to the M-series Mass Connection Solutions
or third party wiring solutions from Phoenix or if IS Barriers
are required from Pepperl and Fuchs, mounted in an adjacent
cabinet to meet special signal conditioning or for optimizing
field wiring solutions. Please refer to the Alliance Program
website for details on approved third-party products.
„ 10-pin Mass Termination Block (simplex only)
„ 16-pin Mass Termination Block (simplex only)
„ 24-pin Mass Termination Block (simplex only)
„ 40-pin Mass Termination Block (simplex and redundant)
„ 48-pin Mass Termination Block (simplex and redundant)channel, 24V DC, Isolated.
DeltaV M-series Traditional I/O August 2022
www.emerson.com/deltav 21
Specifications for SOE Card, 16-channel, 24V DC, Dry Contact
Number of Channels 16
Detection Level for On >2 mA
Detection Level for Off <0.25 mA
Input Impedance 5K ohm (approximate)
Wetting Voltage 24V DC
Channel Scan Rate 0.25 msec for all 16 channels
Time Stamp Accuracy (for SOE enabled channels only)* 0.25 msec from same card
1 msec from same controller
LocalBus Current (12V DC nominal) 75 mA typical, 100 mA maximum
Field Circuit Power per Card 75 mA at 24V DC
Isolation Each channel is optically isolated from the system
and factory tested to 1500V DC