KJ3202X1-BA1模块备件

KJ3202X1-BA1

KJ3202X1-BA1 DO，24 VDC，高压侧，系列
2卡
危险大气
二、3g
Nemko No.02ATEX431U
EEx nA IIC T4
功率规格
150 mA时的本地总线额定功率12 VDC
总线现场电源
评级
3.0 A时的30 VDC
1 A/通道3下的现场电路额定值为30 VDC
A/卡
环境规范
环境温度-40至70摄氏度
冲击10g½正弦波持续11毫秒
振动：1毫米，峰间频率为5至16Hz；
0.5g，从16到150Hz
空运的
污染物
ISA-S71.04–1985机载
G3类污染物
相对湿度5-95%，不冷凝，IP 20
评级
接线盒键
位置
B6
注：序列号参见产品标签
以及制造地点和日期。还参考
板卡左侧的接线图。
警告：本产品具有以下特定说明：
危险环境中的安装、拆除和操作
地区。参考文件12P2046“DeltaV
可扩展工艺系统2区安装
其他安装说明包括
在“安装您的DeltaV自动化”中提供
系统”手册。
移除和插入
在现场向该设备提供的现场电源
终端或通过
托架，必须在拆卸前拆下，或
连接设备。
系统运行时，可移除或插入该装置
电源在以下条件下通电：
（注：一次只能拆除一个装置
系统电源已通电。）
•与KJ1501X1-BC1系统双联使用时
在24 VDC或以下电压下运行的DC/DC电源
12 VDC输入电源。主电路布线
输入功率的电感必须小于23
呃，或者是有开路的认证电源
电压，Ui为12.6 VDC，Lo小于
23 uH（包括导线电感）。
•拆除和插入无火花励磁电路之前，必须将其断电
产品
接线盒保险丝不得在以下情况下拆除：
无火花电路的励磁电源。
维护和调整
该装置不包含用户可维修部件，并且
不得因任何原因拆卸。
不需要校准。
其他安全许可

KJ3202X1-BA1

KJ3202X1-BA1
KJ3202X1-BA1 DO, 24 VDC, High-Side, Series
2 Card
Hazardous Atmosphere
 II 3 G
Nemko No. 02ATEX431U
EEx nA IIC T4
Power Specifications
LocalBus power rating 12 VDC at 150 mA
Bussed field power
rating
30 VDC at 3.0 A
Field circuit rating 30 VDC at 1 A/channel, 3
A/card
Environmental Specifications
Ambient Temperature -40 to 70o C
Shock 10g ½ Sinewave for 11 msec
Vibration 1mm Peak to Peak from 5 to 16Hz;
0.5g from 16 to 150Hz
Airborne
Contaminants
ISA-S71.04 –1985 Airborne
Contaminants Class G3
Relative Humidity 5 to 95% Non-Condensing IP 20
Rating
Terminal block key
position
B6
Note: Refer to the product label for serial number
and location and date of manufacture. Refer also to
the wiring diagram on the left side of the card.
Warning: This product has specific instructions for
installation, removal and operation in hazardous
areas. Refer to document 12P2046 "DeltaV 
Scalable Process System Zone 2 Installation
Instructions". Other installation instructions are
available in the "Installing Your DeltaV Automation
System" manual.
Removal and Insertion
Field power supplied to this device, either at the field
terminal or as bussed field power through the
carrier, must be removed before removing or
connecting the device.
This unit may be removed or inserted while system
power is energized under the following conditions:
(Note Only one unit at a time may be removed with
system power energized.)
• When used with KJ1501X1-BC1 System Dual
DC/DC Power Supply operating on 24 VDC or
12 VDC input power. The primary circuit wiring
inductance for input power must be less than 23
uH, or a certified supply with an open circuit
voltage, Ui of 12.6 VDC and an Lo of less than
23 uH (including wire inductance).
• Non sparking field circuits MUST be deenergized before removing and inserting this
product.
A terminal block fuse may NOT be removed with
field power energized for non-sparking circuits.
Maintenance and Adjustment
This unit contains no user serviceable parts and
should not be disassembled for any reason.
Calibration is not required.
Other Safety Approv