1B30023H02 模块备件

1B30023H02 

g、 5-40多速运行接线
4~5：选择Acc/Dec时间
表5-7 Acc/Dec时间选择
2号航站楼1号航站楼Acc/Dec时间
选择
关断Acc时间1/12月时间1
OFF ON Acc时间2/Dec时间2
开-关Acc时间3/12月时间3
ON ON Acc时间4/Dec时间4
通过端子的开/关组合，Acc/Dec
可选择时间1~4。
6~7：输入外部故障信号（常开/常闭
输入）
如果设置为6~7，则外部故障信号
设备可通过终端输入，终端为
方便驱动器监控外部
设备一旦驱动器接收到故障信号
将显示“E015”。故障信号有两个输入
模式：常开和常闭输入。
X5
X6
组件对象模型
公里
EV2000
·
·
·
图5-41常开/常闭输入
如图5-41所示，X5为常开触点
X6为常闭命令。KM是
输入外部故障信号。
8： 输入外部复位信号
如果设置为8，则可通过该端子重置驱动器
当驱动器出现故障时。该终端的功能
与面板上的复位相同。
9~10：输入点动操作信号（点动/点动）
如果设置为9~10，该终端可以启用点动
活动JOGF用于输入正向jog命令
JOGR表示反向jog命令。点动频率，
点动操作的间隔和Acc/Dec时间在中定义
F3.13~F3.16。
11： 停下来
如果设置为11，则终端的功能为
与F2.08定义的相同。方便
遥控器
12~13：频率上升/DN
如果设置为12~13，则终端可用于
增加或减少频率。它的功能是一样的
面板上有c和d键，可启用远程
控制当F0.00=1或
F9.01=2.增加或减少率由以下因素确定：
F7.09。
14： 暂停PLC操作：
如果设置为14，则终端用于暂停PLC
在以下情况下，驱动器以零频率运行：
终端被启用。PLC没有定时
活动如果终端被禁用，驱动器将启动
并继续PLC操作。参考
F4.00~F4.14了解如何使用此终端。
15： Acc/Dec禁止命令
如果设置为15，则终端可以使电机
以当前速度运行，不受以下因素的影响：
外部信号（停止命令除外）。
注：
该终端在正常Dec中被禁用以停止进程。
16： 三线操作控制。
参见F7.08，操作模式2和3（三线制
操作模式1和2）。
17~18：输入外部停止信号
（常开/常闭输入）
运行期间，驱动器停止输出并运行
当其接收到外部停止信号时处于零频率。
信号消除后，驱动器将立即启动
并恢复正常操作。
外部停止有两种输入模式：
信号：常开和常闭输入。像
如图5-41所示，X5为常开触点，X6
通常为紧密接触。
第5章参数介绍63
EV2000系列通用变速驱动用户手册
注：
与6~7号功能不同，外部停止
信号不会触发报警，驱动器可以恢复
信号消除后的正常操作。
19： 直流注入制动信号
如果设置为19，则终端可用于执行
对正在运行的电机进行直流注入制动，以便：
实现紧急停止和准确定位
发动机初始制动频率、制动延迟时间和
制动电流由F2.09~F2.11定义。制动
时间是F2.12和
此控制定义的有效连续时间
航空站
20： 禁用闭环功能
如果设置为20，则可使用终端实现
在闭环操作和
低液位运行模式（参见第4.1.4节
细节）。
注：
操作模式之间的切换仅在以下情况下启用：
闭环操作（F5.00=1）。
当驱动器切换到低电平操作模式时，
其启动/停止、运行方向、ACC/Dec时间应
符合相应的操作模式。
21：禁用PLC
如果设置为21，则终端用于实现
PLC操作和低液位之间的灵活切换
操作模式（详见第4.1.4节）。
注：
可以启用操作模式之间的切换
仅在PLC操作中（F4.00的单元位置不是0）。
当驱动器切换到低电平操作模式时，
其启动/停止、运行方向、ACC/Dec时间应
符合相应的操作模式
照着
22~24：参考频率选择器的端子1~3。
端子1、2和3的不同开/关组合
可以选择不同的参考频率选择器，如
如表5-8所示。驱动器将根据命令进行操作
从终端或F0.00，以较晚者为准。
表5-8频率选择器
端子3、端子2、端子1频率选择器
关，关，关。保持设置
脱离

1B30023H02 

1B30023H02 

g. 5-40 Wiring for multi-speed operation
4~5: selecting Acc/Dec time
Table 5-7 Acc/Dec time selection
Terminal 2 Terminal 1 Acc/Dec time
selection
OFF OFF Acc time 1/Dec time 1
OFF ON Acc time 2/Dec time 2
ON OFF Acc time 3/Dec time 3
ON ON Acc time 4/Dec time 4
Through the On/Off combinations of terminals, Acc/Dec
time 1~4 can be selected.
6~7: inputting external fault signal (normally-open/close
input)
If the setting is 6~7, the fault signal of external
equipment can be input via the terminal, which is
convenient for the drive to monitor the external
equipment. Once the drive receives the fault signal, it
will display “E015”. The fault signal has two inputting
modes: normally-open and normally-close input.
X5
X6
COM
KM
EV2000
·
·
·
Fig. 5-41 Normally-open/close input
As shown in Fig. 5-41, X5 is normally-open contact and
X6 is normally-close command. KM is the relay for
inputting external fault signal.
8: inputting external reset signal
If the setting is 8, the drive can be reset via this terminal
when the drive has a fault. The function of this terminal
is the same with that of RESET on the panel.
9~10: inputting jog operation signal (JOGF/JOGR)
If the setting is 9~10, this terminal can enable jog
operation. JOGF is for inputting forward jog command
and JOGR is for reverse jog command. Jog frequency,
interval and Acc/Dec time of jog operation are defined in
F3.13~F3.16.
11: Coast-to-stop
If the setting is 11, the function of the terminal is the
same with that defined by F2.08. It is convenient for
remote control.
12~13: Frequency ramp UP/DN
If the setting is 12~13, the terminal can be used to
increase or decrease frequency. Its function is the same
with c and d keys on the panel, which enables remote
control. This terminal is enabled when F0.00=1 or
F9.01=2. Increase or decrease rate is determined by
F7.09.
14: pausing PLC operation:
If the setting is 14, the terminal is used to pause the PLC
operation and the drive operates at zero frequency when
the terminal is enabled. There is no timing of PLC
operation. If the terminal is disabled, the drive will start
on the fly and continue the PLC operation. Refer
F4.00~F4.14 to how to use this terminal.
15: Acc/Dec prohibiting command
If the setting is 15, the terminal can make the motor
operate at present speed without being influenced by
external signal (except stopping command).
     Note:
 This terminal is disabled in normal Dec-to-stop process.
16: 3-wire operation control.
Refer to F7.08, operation mode 2 and 3 (3-wire
operation mode 1 and 2).
17~18: inputting external stopping signal
(Normally-open/close input)
During operating, the drive stops its output and operates
at zero frequency when it receives external STOP signal.
Once the signal is removed, the drive will start on the fly
and resume normal operation.
There are two inputting modes of external stopping
signal: normally-open and normally-close input. As
shown in Fig. 5-41, X5 is normally-open contact and X6
is normally-close contact. 
Chapter 5 Parameter Introductions 63
EV2000 Series Universal Variable Speed Drive User Manual
     Note:
Different with No. 6~7 functions, the external stopping
signal will not trigger alarm and the drive can resume
normal operation after the signal is removed.
19: DC injection braking signal
If the setting is 19, the terminal can be used to perform
DC injection braking to the motor that is running so as to
realize the emergent stop and accurate location of the
motor. Initial braking frequency, braking delay time and
braking current are defined by F2.09~F2.11. Braking
time is the greater value between F2.12 and the
effective continuous time defined by this control
terminal.
20: disabling close-loop function
If the setting is 20, the terminal can be used to realize
the flexible switching between close-loop operation and
low level operating mode (refer to section 4.1.4 for
details).
     Note:
The switching between operation modes is enabled only in
close-loop operation (F5.00=1).
When the drive is switched to low level operating mode,
its start/stop, operating direction, ACC/Dec time should
be compliant with corresponding operating modes.
21: disabling PLC
If the setting is 21, the terminal is used to realize the
flexible switching between PLC operation and low level
operating mode (refer to section 4.1.4 for details).
     Note:
The switching between operation modes can be enabled
only in PLC operation (unit’s place of F4.00 is not 0).
When the drive is switched to low level operating mode,
its start/stop, operating direction, ACC/Dec time should
be compliant with corresponding operating modes
accordingly.
22~24: Terminals 1~3 for reference frequency selector.
Different ON/OFF combinations of terminals 1, 2 and 3
can select different reference frequency selectors as
shown in Table 5-8. The drive will act to the command
from the terminal or F0.00, whichever comes late.
Table 5-8 Frequency selector
Terminal 3 Terminal 2 Terminal 1 Freq. selector
OFF OFF OFF Hold the setting
OFF OFF ON Digital setting 1
OFF ON OFF Digital setting 2
OFF ON ON Digital setting 3
ON OFF OFF VCI analog input
Terminal 3 Terminal 2 Terminal 1 Freq. selector
ON OFF ON CCI analog input
ON ON OFF PULSE terminal
input
ON ON ON PULSE terminal
input
25:Frequency reference is input via terminal CCI forcibly
If the setting is 25, the frequency reference will be input
via terminal CCI forcibly. The frequency selector will be
changed to the previous one if this terminal function is
disabled.
26:Reserved
27: Terminal control mode is forcibly enabled
When this terminal function is enabled, the operating
command is input through this terminal forcibly, and the
drive will be controlled in previous control mode if
FWD/REV terminal function is disabled.
28~29: On/Off combinations of terminals 1 and 2 for
different control modes selection
Table 5-9 Control modes
Terminal 2 Terminal 1 Control modes
OFF OFF Hold the control mode
OFF ON Panel control mode
ON OFF Terminal control mode
ON ON Serial port control mode
The control modes in Table 5-9 can be selected by the
different On/Off combinations of terminals 1 and 2.
30~32: Selecting preset close-loop reference
frequencies via On/Off combinations of terminals 1~3.
Table 5-10 Preset close-loop reference selection
Terminal 3 Terminal 2 Terminal 1 Preset close-loop
reference selection
OFF OFF OFF Close-loop reference
 is decided by F5.01
OFF OFF ON Preset close-loop
reference 1
OFF ON OFF Preset close-loop
reference 2
OF ON ON Preset close-loop
reference 3
ON OFF OFF Preset close-loop
reference 4
ON OFF ON Preset close-loop
reference 5
ON ON OFF Preset close-loop
reference 6
ON ON ON Preset close-loop
referenc