1C31227G01 模块备件

1C31227G01 

访问代码
访问代码用于启用和解除系统。有37个可用的访问代码：1个主
代码、32个常规访问代码、2个胁迫代码和2个监管代码。询问您的安装程序以了解更多信息
关于使用胁迫和监督代码的信息。
只有主代码可用于编程其他安全代码和更改其他系统
以及对安全系统进行防护和解除防护。主代码将由您的
安装程序。每次按一个键即可完成所有键盘输入。
可以按照“编程安全性”中概述的程序对所有访问代码进行编程
7页的“代码”。
注意：访问代码可以是四位或六位数字，具体取决于您的安装程序
在你的系统中编程。请向安装程序询问有关访问代码的更多信息。
武装系统
通过LED键盘进行防护：
如果就绪指示灯亮起，系统准备就绪。如果就绪灯熄灭，请检查以确保所有
门窗关闭，在运动检测器覆盖的区域停止运动。这个
除非“就绪”指示灯亮起，表明所有区域均已关闭，系统无法启用
处于就绪状态。
输入您的访问代码。当输入每个数字时，键盘发声器将发出嘟嘟声。如果访问代码是
如果输入不正确，键盘蜂鸣器将持续鸣响一秒钟。如果出现这种情况，请按[#]
键入并重新输入您的访问代码。如果输入了正确的访问代码，键盘发声器将发出蜂鸣音
很快，武装灯就会亮起。通过安装人员指示的门离开现场
作为出口/入口门。
面板将提供一个退出延迟时间，由键盘蜂鸣声指示，供您退出场所
而不会引起警报。在退出延迟期结束时，除预位灯外，
将关闭，系统将启用。您可以通过按“离开”重新启动退出延迟一次
退出延迟到期前的按钮。退出延迟时间可以由安装程序更改。
从LCD键盘解除武装：
当您尝试启用系统时，可能会出现以下消息之一：
一个或多个区域不安全。要固定系统，请关闭所有车门和
窗口并停止运动检测器覆盖区域内的所有运动。
使用箭头（<>）键验证系统是否无故障且无区域
无意中被旁路（参见“查看故障条件”和“区域旁路”
11页）。
如果您看到此消息，则说明安装程序已设置了系统，以便可以对其进行防护
其中一个或多个指定区域打开。请咨询您的安装程序以了解更多详细信息。
系统处于就绪状态，可以完全启用。要启用系统，请输入
这是您的访问代码。
输入正确的访问代码后，显示将为：
面板将提供退出延迟时间，也由键盘蜂鸣声指示，以便您
在不引起警报的情况下离开现场。您可以通过以下方式重新启动退出延迟一次：
在退出延迟到期之前按下离开按钮。从指定的门退出
由您的安装程序作为出口/入口门。
退出延迟到期且系统完全关闭后，将显示此消息
武装。
如果出现此消息，请注意哪些区域被绕过以及原因（请参见“区域
旁路”，见10页）。注意：如果您使用绕过的区域或
如果出现问题，您的安全保护将降低。
安全系统
武装前<>
输入代码
Arm系统<>
输入代码
Arm系统
出口延迟
进步
*警告*
旁路激活
输入代码
解除系统
安全系统
或输入代码
5.
备用武装方法

1C31227G01 

1C31227G01 

Access Codes
Access codes are used to arm and disarm the system. There are 37 access codes available: 1 master
code, 32 regular access codes, 2 duress codes and 2 supervision codes. Ask your installer for more
information on using the duress and supervision codes.
Only the Master Code can be used to program additional security codes and to change other system
features as well as to arm and disarm the security system. The Master Code will be supplied to you by your
installer. All keypad entries are made by pressing one key at a time.
All access codes can be programmed by following the procedure outlined in “Programming Security
Codes” on page 7.
NOTE: An access code can be a four or six digit number depending on how your installer has
programmed your system. Ask your installer for more information regarding access codes.
Arming the System
Arming from an LED Keypad:
If the Ready light is ON, the system is ready for arming. If the Ready light is OFF, check to see that all
doors and windows are closed and that motion is stopped in areas covered by motion detectors. The
system cannot be armed unless the Ready light is ON indicating that all zones are closed and the system
is in the Ready state.
Enter your access code. As each digit is entered, the keypad sounder will beep. If the access code was
entered incorrectly, the keypad buzzer will sound steadily for one second. If this occurs, press the [#]
key and re-enter your access code. If the correct access code is entered, the keypad sounder will beep
quickly and the Armed light will come ON. Exit the premises through the door indicated by your installer
as the Exit/Entry door.
The panel will provide an exit delay period, indicated by keypad beeps, for you to exit the premises
without causing an alarm. At the end of the exit delay period, all keypad lights, except the Armed light,
will turn OFF and the system will be armed. You can restart the exit delay once by pressing the Away
button before the exit delay expires. The exit delay time can be changed by your installer.
Arming from an LCD Keypad:
One of the following messages may appear when you attempt to arm your system:
One or more zones are not secured. To secure the system, close all doors and
windows and cease all motion in areas covered by motion detectors.
Use the arrow (< >) keys to verify that the system is clear of troubles and that no zones
are bypassed unintentionally (see “Viewing Trouble Conditions” and “Zone Bypassing”
on page 11).
If you see this message, your installer has set up your system so that it may be armed
with one or more designated zones open. Ask your installer for more details.
The system is in the Ready state and may be fully armed. To arm the system, enter
your access code.
Once the correct access code has been entered, the display will be:
The panel will provide an exit delay period, also indicated by keypad beeps, for you to
exit the premises without causing an alarm. You can restart the exit delay once by
pressing the Away button before the exit delay expires. Exit through the door indicated
by your installer as the Exit/Entry door.
This message will be displayed once the exit delay expires and the system is fully
armed.
If this message appears, be aware of which zones are bypassed and why (see “Zone
Bypassing” on page 10). NOTE: If you arm the system with a zone bypassed or
with a trouble present, your security protection is reduced.
Secure System
Before Arming <>
Enter Code to
Arm System <>
Enter Code to
Arm System
Exit Delay in
Progress
* WARNING *
Bypass Active
Enter Code to
Disarm System
Secure System
or Enter Code
5
Alternate Arming Methods