1C31232G03 模块备件

1C31232G03 

沙丁鱼系统
从LED键盘解除防护：
通过指定的出口/入口门进入场所。从任何其他门进入都会发出
立即报警。出口/入口门打开后，键盘将发出嘟嘟声，指示
应解除系统。转到键盘并输入您的访问代码。如果你犯了错误
输入您的代码，请重新正确输入代码。输入正确的代码后，武装
灯将熄灭，键盘将停止蜂鸣。
必须在输入延迟期到期之前输入正确的访问代码。如果是有效访问
在此期间未输入代码，系统将进入报警状态。您的安装程序可以更改该项
时间延迟。
如果在系统启用时发生报警，则相应的内存指示灯和区域指示灯
导致报警的区域将闪烁30秒。30秒后，存储器
指示灯和区域指示灯将停止闪烁，面板将返回就绪状态。按[#]键
在30秒期间，将取消报警记忆显示。要查看其他报警，请按[✱][3].
如果在面板解除防护时检测到故障，故障灯将点亮（请参见“查看
11页的“故障条件”，以确定故障源。）请注意，麻烦将
系统处于报警记忆显示模式时不显示。
从LCD键盘解除防护：
通过指定的出口/入口门进入时，键盘将发出蜂鸣音，进入延迟将
开始，提醒你解除系统。键盘将显示以下消息。。。
输入您的访问代码。如果在输入代码时出错，请重新输入
正确编码。输入有效的访问代码后，键盘将停止
嘟嘟声。如果面板处于待命状态时没有警报，并且没有
故障，显示器将显示。。。
大约五秒钟后，系统将返回就绪状态并显示
这将是。。。
如果系统启用时出现警报，将显示此消息。
使用箭头（＜>）键查看引起报警的区域。如果某个区域仍在
报警，显示器将显示以下消息，以指示区域已打开。。。
解除防护后，如果出现故障，将显示此消息。使用
箭头（＜>）键查看影响系统的故障（请参见“查看
11页的“故障条件”）。
注意：如果您返回时发现在您不在时发生了报警，则可能：
入侵者可能仍在现场。去邻居家，打电话给当地警察
侦查
每次启用面板时，报警存储器都会被清除。显示的任何报警都是：
仅在上次武装期间发生。

1C31232G03 

1C31232G03 

sarming the System
Disarming from an LED Keypad:
Enter the premises through a designated Exit/Entry door. Entering by any other door will sound an
immediate alarm. As soon as the Exit/Entry door is opened, the keypad will beep to indicate that the
system should be disarmed. Go to the keypad and enter your access code. If you made an error
entering your code, re-enter the code correctly. As soon as the correct code is entered, the Armed
light will go out and the keypad will stop beeping.
The correct access code must be entered before the entry delay period expires. If a valid access
code is not entered during this time, the system will go into alarm. Your installer can change the entry
time delay.
If an alarm occurred while the system was armed, the Memory light and the zone light corresponding
to the zone that caused the alarm will flash for 30 seconds. After the 30-second period, the Memory
light and zone light will stop flashing and the panel will return to the Ready state. Pressing the [#] key
during the 30 second period will cancel the alarm memory display. To view other alarms, press [✱][3].
If a trouble was detected when the panel is disarmed, the Trouble light will turn ON (See “Viewing
Trouble Conditions” on page 11 to determine the source of the trouble.) Please note that troubles will
not display while the system is in the Alarm Memory Display mode.
Disarming from an LCD Keypad:
Upon entering through a designated Exit/Entry door, the keypad will beep and the entry delay will
commence, reminding you to disarm the system. The keypad will display the following message...
Enter your access code. If an error is made in entering the code, re-enter the
code correctly. When a valid access code is entered, the keypad will stop
beeping. If there were no alarms while the panel was armed, and there are no
troubles, the display will read...
After about five seconds, the system will return to the Ready state and the display
will read...
If there was an alarm while the system was armed, this message will be displayed.
Use the arrow (< >) keys to view which zones caused the alarm. If a zone is still in
alarm, the display will show the following message to indicate that a zone is open...
Upon disarming and if a trouble is present, this message will be displayed. Use the
arrow (< >) keys to view which troubles are affecting the system (see “Viewing
Trouble Conditions” on page 11).
NOTE: If you return and find that an alarm has occurred while you were away, it is possible that
an intruder may still be on the premises. Go to a neighbour’s house, and call the local police to
investigate.
The alarm memory is cleared each time the panel is armed. Any alarms showing are alarms that
occurred only during the last armed period.