1C31233G04 模块备件

1C31233G04 

记忆灯
解除防护时，如果在
系统已启用，记忆灯将亮起
打开（请参见6页的“解除系统武装”）。
旁路灯
如果旁通灯亮起，则一个或多个区域为
旁路（见11页的“区域旁路”）。
火光
如果消防灯亮起，则发生火灾报警
（参见14页的“火灾报警操作”）。
节目灯
当您处于以下状态时，程序指示灯将闪烁：
编程访问代码，或执行其他
编程功能。如果有人
在另一个键盘上编程，程序指示灯
将打开以指示系统忙。
PC5516（Z）LED键盘
PC5516、PC5516Z、PC5532和PC5532Z键盘可用于以下应用：
8个区域。本手册中解释的功能对于所有三种LED键盘类型都相同。
PC5532（Z）LED键盘
9
液晶显示器（LCD）显示
两个16的提示和系统信息
字符行。
如果出现“＜>”，可以查看更多信息
使用箭头（＜）键访问。按〔＜〕
查看以前的功能或信息项。
按[>]可将显示前进到下一个功能
或信息项。
根据提示按数字键盘上的键
通过LCD显示器查看报警或故障，以
启用和解除系统以及绕过区域。
为了退出功能并返回到就绪状态，
按[#]。
要选择功能，请按[✱].
LCD5500Z键盘
应急钥匙（所有键盘）
按两个*键两秒钟以发送
火灾传播。
按两个*键两秒钟以发送
辅助变速器。
按两个*键两秒钟以发送
恐慌传播。
*重要提示（所有键盘）：火灾，
辅助和紧急钥匙将不起作用
除非由安装者编程。如果这些
密钥正在使用中，安装程序已启用
声音反馈，按住键两次
秒将导致键盘发声器发出嘟嘟声
指示输入已被接受，以及
传输正在进行。
重要提示：每周测试系统，并检查是否存在任何系统故障
由您的报警安装程序更正。
LCD5501Z键盘
10
来自LCD键盘的编程代码：
主代码
按[✱] 键进入功能列表。滚动（＜>）到。。。
按[5]或[✱]. 显示器将显示。。。
输入您当前的主代码。显示器将显示。。。
“40P”表示主代码。按[✱] 表示您希望：
对主代码进行编程。显示器将显示。。。
输入新的主代码。主代码必须为四位数，除非
安装程序另有指示。仅输入数字0到9。一旦新的
输入代码后，键盘将蜂鸣3次，显示屏将显示。。。
按[#]退出代码编程功能。
请务必在本手册的“系统信息”页上记录新的主代码。注：我们
建议不要使用出厂默认主代码[1234]。
附加访问代码
要删除、添加或更改用户代码，请按[✱] 以进入功能列表。使用箭头（<>）键：
滚动到以下消息。。。
压榨[✱]. 显示器将显示。。。
输入主代码。显示器将显示。。。
使用滚动键（<>）查找访问代码–由“02P”到“32P”指示
您希望添加、更改或删除。主席

1C31233G04 

1C31233G04 

Memory Light
Upon disarming, if an alarm has occurred while
the system was armed, the Memory light will turn
ON (See “Disarming the System” on page 6).
Bypass Light
If the Bypass light is ON, one or more zones are
bypassed (See “Zone Bypassing” on page 11).
Fire Light
If the Fire light is ON, a fire alarm has occurred
(See “Fire Alarm Operation” on page 14).
Program Light
The Program light will flash when you are
programming access codes, or performing other
programming functions. If someone is
programming at another keypad, the Program light
will turn ON to indicate that the system is busy.
PC5516(Z) LED Keypad
The PC5516, PC5516Z, PC5532 and PC5532Z Keypads are available for applications with more than
8 zones. The functions explained in this manual are the same for all three LED keypad types.
PC5532(Z) LED Keypad
9
The Liquid Crystal Display (LCD) displays
prompts and system information on two 16
character lines.
If “< >” appears, more information can be
accessed by using the arrow (< >) keys. Press [<]
to see the previous function or item of information.
Press [>] to advance the display to next function
or item of information.
Press the keys on the number pad as prompted
by the LCD display to view alarms or troubles, to
arm and disarm the system and to bypass zones.
To exit a function and return to the Ready state,
press [#].
To select a function press [✱].
LCD5500Z Keypad
Emergency Keys (All Keypads)
Press both * Keys for two seconds to send a
FIRE transmission.
Press both * Keys for two seconds to send an
AUXILIARY transmission.
Press both * Keys for two seconds to send a
PANIC transmission.
* IMPORTANT NOTE (All Keypads): The Fire,
Auxiliary and Panic keys will NOT function
unless programmed by the installer. If these
keys are in service and the installer has enabled
audible feedback, holding down the key for two
seconds will cause the keypad sounder to beep
indicating that the input has been accepted and
transmission is underway.
Important Note: Test system weekly and have any system trouble conditions
corrected by your alarm installer.
LCD5501Z Keypad
10
Programming codes from an LCD Keypad:
Master Code
Press the [✱] key to enter the function list. Scroll (< >) to...
Press [5] or [✱]. The display will read...
Enter your current Master Code. The display will read...
“40P” represents the Master Code. Press the [✱] key to indicate that you wish to
program the Master Code. The display will read...
Enter the new Master Code. The Master Code must be four digits long, unless
otherwise indicated by your installer. Enter digits 0 through 9 only. Once the new
code is entered, the keypad will beep 3 times and the display will read...
Press [#] to exit the code programming function.
Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We
recommend that the factory default Master Code [1234] not be used.
Additional Access Codes
To erase, add or change a user code, press [✱] to enter the function list. Use the arrow (< >) keys to
scroll to the following message...
Press [✱]. Display will read...
Enter the Master Code. Display will read...
Use the scroll keys (< >) to find the access code – indicated by “02P” to “32P” –
you wish to add, change or delete. Pres