1C31234G01 模块备件

1C31234G01 

输入主代码。显示器将显示。。。
使用滚动键（<>）查找访问代码–由“02P”到“32P”指示
您希望添加、更改或删除。按[✱] 键选择您想要的代码
改变显示器将显示。。。
要添加或更改代码，请输入新代码。访问代码必须是四位数字
除非安装程序另有说明。仅输入数字0到9。删除
访问代码，输入[✱]. 一旦输入4位代码，或[✱] 已输入，则
键盘发声器将鸣响3次，显示屏将显示。。。
“P”表示代码已编程。如果没有“P”，则该代码为
删除。按[#]退出代码编程功能。主代码不能为
擦除。
请记住在本手册的“系统信息”页上记录您的新代码。
访问代码属性
可以激活或停用其他可编程属性，如区域旁路能力
对于每个访问代码。有关访问代码属性的更多信息，请联系
安装程序。
按（*）以获取<>
访问代码
入主
访问代码
[*]编辑<>
用户代码01P
输入新代码
1234 <>
[*]编辑<>
用户代码01P
（*）编辑<>
用户代码40P
入主
访问代码
（*）编辑<>
用户代码40P
输入新代码
1234 <>
按（*）以获取<>
访问代码
11
区域旁路
当需要访问受保护区域的一部分时，使用区域旁路功能
系统已启用。由于线路或触点损坏而暂时停止使用的区域可能是：
旁路，以便在进行维修之前启用系统。
旁路区域不会引起报警。系统启用后，无法绕过区域。
每次解除系统防护时，旁路区域都会自动取消，必须重新应用
在下一次武装之前。
注意：出于安全原因，您的安装程序可能会对系统进行编程，以防止您：
绕过某些区域。
绕过区域会降低您的安全保护。如果由于损坏而绕过某个区域
接线或触点，请立即致电维修技术人员，以便解决问题
已解决，系统已恢复正常工作状态。
确保在配置系统时没有无意中绕过任何区域。
要绕过LED键盘的区域：
从系统处于就绪状态开始。进入[✱][1] [待绕过的区域]。
以从01到08的2位数字输入区域。当绕过每个区域时，相应的区域
指示灯将亮起。如果错误地绕过了某个区域，请再次输入该区域编号；区域灯将亮起
关闭，表示该区域未被绕过。按[#]返回就绪状态。
要绕过LCD键盘的区域，请执行以下操作：
要绕过区域，系统必须处于就绪状态。显示器将显示。。。
按[✱] 键进入功能菜单。显示器将显示。。。
按[✱] 键进入区域旁路模式。显示器将显示。。。
使用箭头（＜>）键查找要绕过的区域，然后按[✱] 关键
选择它。显示器将显示。。。
“B”将出现在显示器上，表示该区域已被绕过。解开a
区域，输入区域编号；“B”将从显示器上消失，以显示
区域不再被绕过。
当您进入旁路时，如果区域打开，将显示此显示
命令开放区将用“O”表示。如果绕过开放区，则
“B”将取代“O”。
要退出旁路模式并返回就绪状态，请按[#]键。
查看故障条件
控制面板持续监控许多可能的故障状况。如果这些麻烦之一
出现这种情况时，键盘将每10秒发出两次蜂鸣声，直到您按下键盘上的任何键。
注意：故障情况会降低系统设计提供的安全性。打电话给你
安装服务公司。
输入代码
Arm系统
按（*）以获取<>
区域旁路
区域搜索<>
“区域名称”
区域搜索<>
“区域名称”B
区域搜索<>
“区域名称”O
12
从LED查看故障

1C31234G01 

1C31234G01 

Enter the Master Code. Display will read...
Use the scroll keys (< >) to find the access code – indicated by “02P” to “32P” –
you wish to add, change or delete. Press the [✱] key to select the code you wish to
change. The display will read...
To add or change a code, enter the new code. Access codes must be four digits
unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete
an access code, enter [✱]. Once the 4-digit code or [✱] has been entered, the
keypad sounder will beep 3 times and the display will read...
The “P” means the code has been programmed. If there is no “P” then that code is
deleted. Press [#] to exit the code programming function. The Master code cannot be
erased.
Remember to record your new code(s) on the “System Information” page in this booklet.
Access Code Attributes
Additional programmable attributes, such as zone bypassing capability, can be activated or deactivated
for each access code. For more information regarding access code attributes, please contact your
installer.
Press (*) for <>
Access Codes
Enter Master
Access Code
[*] to Edit <>
User Code 01P
Enter New Code
1234 <>
[*] to Edit <>
User Code 01P
(*) to Edit <>
User Code 40P
Enter Master
Access Code
(*) to Edit <>
User Code 40P
Enter New Code
1234 <>
Press (*) for <>
Access Codes
11
Zone Bypassing
The zone bypassing function is used when access is needed to part of the protected area while the
system is armed. Zones that are temporarily out of service due to damaged wiring or contacts may be
bypassed to allow system arming until repairs can be made.
Bypassed zones will not cause an alarm. Zones cannot be bypassed once the system is armed.
Bypassed zones are automatically cancelled each time the system is disarmed and must be reapplied
before the next arming.
NOTE: For security reasons, your installer may program the system to prevent you from
bypassing certain zones.
Bypassing zones reduces your security protection. If you are bypassing a zone due to damaged
wiring or contacts, please call a service technician immediately so that the problem can be
resolved and your system returned to proper working order.
Make sure that no zones are unintentionally bypassed when arming your system.
To bypass zones from an LED keypad:
Start with the system in the Ready state. Enter [✱][1][Zone(s) to be bypassed].
Enter the zone(s) as a 2-digit number from 01 to 08. As each zone is bypassed, the corresponding zone
light will turn ON. If a zone is bypassed by mistake, enter that zone number again; the zone light will turn
OFF, indicating that the zone is not bypassed. Press [#] to return to the Ready state.
To bypass zones from an LCD keypad:
To bypass a zone, the system must be in the Ready state. The display will read...
Press the [✱] key to enter the function menu. The display will read...
Press the [✱] key to enter the zone bypassing mode. The display will read...
Use the arrow (< >) keys to find the zone to be bypassed and press the [✱] key to
select it. The display will read...
“B” will appear on the display to show that the zone is bypassed. To unbypass a
zone, enter the zone number; the “B” will disappear from the display to show that the
zone is no longer bypassed.
This display will be shown if a zone was open when you entered the bypassing
command. The open zone will be represented by “O”. If you bypass the open zone, a
“B” will replace the “O”.
To exit the bypassing mode and return to the Ready state, press the [#] key.
Viewing Trouble Conditions
The control panel continuously monitors a number of possible trouble conditions. If one of these trouble
conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.
NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your
installing company for service.
Enter Code to
Arm System
Press (*) for <>
Zone Bypass
Zone Search <>
“Zone Name”
Zone Search <>
“Zone Name” B
Zone Search <>
“Zone Name” O
12
To view troubles from an LED