5X00059G01 模块备件

5X00059G01 

5X00059G01 固态设备具有不同于机电设备的操作特性
设备固态控制器应用、安装和维护的安全指南
（出版物SGI-1.1可从当地罗克韦尔自动化销售办公室或在线获取：
http://www.rockwellautomation.com/literature/)描述固态设备和硬接线机电设备之间的一些重要区别。因为这种差异，也因为
固态设备用途广泛，所有负责使用该设备的人员
必须确保该设备的每个预期应用都是可接受的。
在任何情况下，罗克韦尔自动化股份有限公司均不对间接或后果性损害负责
由于使用或应用该设备而导致的。
本手册中的示例和图表仅用于说明目的。因为
与任何特定安装相关的许多变量和要求，罗克韦尔
Automation，股份有限公司不承担基于示例的实际使用责任
以及图表。
Rockwell Automation，股份有限公司对信息、电路、，
本手册中描述的设备或软件。
未经以下人员的书面许可，复制本手册的全部或部分内容：
禁止使用罗克韦尔自动化公司。
在本手册中，如有必要，我们使用注释让您了解安全注意事项。
警告：标识有关可能导致
在危险环境中爆炸，可能导致人身伤亡、财产损失
损坏或经济损失。
注意：识别有关可能导致以下情况的实践或情况的信息：
人身伤害或死亡、财产损失或经济损失。注意事项帮助您识别
危险，避免危险并认识到后果。
电击危险：标签可能位于设备上或设备内部（例如，驱动器或电机）
提醒人们可能存在危险电压。
烧伤危险：标签可能位于设备（例如，驱动器或电机）上或内部，以：
提醒人们表面可能达到危险温度。
重要信息：识别对成功应用和理解以下信息至关重要的信息：
产品。
罗克韦尔自动化出版物1734-IN058E-EN-P-2018年12月3日
点I/O 24V直流扩展电源
环境和外壳
注意：本设备用于污染等级为2的工业
过电压II类应用中的环境（定义见EN/IEC 60664-
1） ，在不降额的情况下，在海拔高达2000米（6562英尺）的情况下。
本设备不适用于居住环境，也可能不适用
在这种环境中为无线电通信服务提供充分的保护。
本设备作为室内使用的开放式设备提供。一定是
安装在外壳内，该外壳适用于特定
将出现的环境条件，并适当设计为：
防止接触带电部件造成人身伤害。围墙
必须具有适当的阻燃性能，以防止或小化蔓延
火焰，符合5VA的火焰蔓延等级，或经批准用于
非金属应用。外壳内部只能通过以下方式进入：
工具的使用。本出版物的后续章节可能包含更多内容
有关要求遵守的特定外壳类型额定值的信息
具有一定的产品安全认证。
除本出版物外

5X00059G01 
Solid-state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid-state Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://www.rockwellautomation.com/literature/) describes some important differences between solidstate equipment and hard-wired electromechanical devices. Because of this difference, and also because of
the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements that are associated with any particular installation, Rockwell
Automation, Inc. cannot assume responsibility or liability for actual use based on the examples
and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of
Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an
explosion in a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss. Attentions help you identify a
hazard, avoid a hazard and recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor)
to alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to
alert people that surfaces may reach dangerous temperatures.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.
Rockwell Automation Publication 1734-IN058E-EN-P - December 2018 3
POINT I/O 24V DC Expansion Power Supply
Environment and Enclosure
ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in EN/IEC 60664-
1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not
provide adequate protection to radio communication services in such environments.
This equipment is supplied as open-type equipment for indoor use. It must be
mounted within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed to
prevent personal injury resulting from accessibility to live parts. The enclosure
must have suitable flame-retardant properties to prevent or minimize the spread
of flame, complying with a flame spread rating of 5VA or be approved for the
application if nonmetallic. The interior of the enclosure must be accessible only by
the use of a tool. Subsequent sections of this publication may contain more
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
In addition to this publication