140XTS33200模块备件

安全信息
重要信息
注意：仔细阅读这些说明，并查看设备以熟悉
在尝试安装、操作或维护设备之前，请检查设备。以下特别
本文档或设备上可能会出现警告信息
潜在危险，或提请注意澄清或简化
程序
在危险或警告安全标签上添加此符号表示：
存在电气危险，如果：
没有遵守说明。
这是安全警报符号。它用于提醒您潜在的个人
伤害危险。遵守此符号后面的所有安全信息，以避免：
可能的伤害或死亡。
危险表示一种迫在眉睫的危险情况，如果不避免，将
导致死亡、重伤或设备损坏。
危险
警告
警告表示潜在危险情况，如果不避免，可能导致
死亡、重伤或设备损坏。
注意安全
小心表示潜在的危险情况，如果不避免，可能会导致
造成伤害或设备损坏。
安全信息
xii 840使用100 00 2004年11月
请注意，电气设备只能由合格人员进行维修。施耐德电气对使用过程中产生的任何后果概不负责
这种材料的。本文件不适用于未经培训的人员
人。
©2004施耐德电气。版权所有。
840使用100 00 11/2004 xiii
关于这本书
一瞥
文档范围：本手册是Quantum自动化硬件的参考指南
系统
有效性注意：本书中的数据和插图不具有约束力。我们保留以下权利：
根据我们的持续产品开发政策修改我们的产品。这个
本文件中的信息如有更改，恕不另行通知
解释为施耐德电气的承诺。
产品相关
警告
施耐德电气对可能出现的任何错误概不负责
文件如果您有任何改进或修改的建议，或
在此出版物中发现错误，请通知我们。
本文件的任何部分不得以任何形式或任何方式复制，包括电子版
或机械，包括影印，未经
施耐德电气。
在下列情况下，必须遵守所有相关的州、地区和地方安全法规
安装和使用本产品。为了安全和确保合规性
在记录系统数据的情况下，只有制造商才能对
组件。
当控制器用于具有技术安全要求的应用时，
请按照相关说明操作。
未能在硬件中使用施耐德电气软件或经批准的软件
产品可能导致不正确的操作结果。
不遵守本产品相关警告可能导致受伤或设备损坏
损坏
用户评论我们欢迎您对此文档的评论。您可以通过电子邮件联系我们：
techpub@schneider-electric.com
关于这本书
xiv 840使用100 00 2004年11月
840使用100 00 11/2004 429
18
量子I/O模块
一瞥
简介：以下部分提供了有关量子输入/输出（I/O）的信息
模块。
这是什么
章
本章包括以下部分：
部分主题页
18.1 I/O模块概述430
18.2模拟输入模块444
18.3模拟输出模块477
18.4模拟输入/输出模块493
18.5离散输入模块504
18.6离散输出模块556
18.7离散验证输出模块619
18.8离散监督输入模块629
18.9离散输入/输出模块634
I/O模块
430 840使用100 00 2004年11月
18.1 I/O模块概述
一瞥
概述本节概述了Quantum中使用的I/O模块。
这是什么
部分
本节包含以下主题：
主题页
量子I/O模块431
I/O映射状态字节442
I/O模块
840使用100 00 11/2004 431
量子I/O模块
概述下一节包含输入/输出模块的规范。单元
说明包括接线图、LED指示灯和说明、插图
对于离散模块，为真高/真低描述。
I/O模块下图显示了I/O组件及其组件。
量子I/O LED
描述
这些表描述了量子I/O模块中使用的通用LED块。
每种类型的I/O模块的独特LED配置说明包含在
本节中的各个I/O模块规格。
  现场接线I/O模块时，大导线尺寸应为
现场接线端子上使用的是1-14 AWG或2-16 AWG；小尺寸为20
特设工作组。
必须订购现场接线端子排（Modicon#140XTS00200）
分别地（端子排包括可拆卸的门和标签。）

10 80 vdc输出
X X
十、
十、
十、
十、
十、Safety Information
Important Information
NOTICE Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
The addition of this symbol to a Danger or Warning safety label indicates
that an electrical hazard exists, which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous situation, which, if not avoided, will
result in death, serious injury, or equipment damage.
DANGER
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided, can result
in death, serious injury, or equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation, which, if not avoided, can result
in injury or equipment damage.
Safety Information
xii 840 USE 100 00 11/2004
PLEASE NOTE Electrical equipment should be serviced only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use
of this material. This document is not intended as an instruction manual for untrained
persons.
© 2004 Schneider Electric. All Rights Reserved.
840 USE 100 00 11/2004 xiii
About the Book
At a Glance
Document Scope This manual is a reference guide for the hardware of the Quantum automation
system.
Validity Note The data and illustrations found in this book are not binding. We reserve the right to
modify our products in line with our policy of continuous product development. The
information in this document is subject to change without notice and should not be
construed as a commitment by Schneider Electric.
Product Related
Warnings
Schneider Electric assumes no responsibility for any errors that may appear in this
document. If you have any suggestions for improvements or amendments or have
found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic
or mechanical, including photocopying, without express written permission of
Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to ensure compliance
with documented system data, only the manufacturer should perform repairs to
components.
When controllers are used for applications with technical safety requirements,
please follow the relevant instructions.
Failure to use Schneider Electric software or approved software with our hardware
products may result in improper operating results.
Failure to observe this product related warning can result in injury or equipment
damage.
User Comments We welcome your comments about this document. You can reach us by e-mail at
techpub@schneider-electric.com
About the Book
xiv 840 USE 100 00 11/2004
840 USE 100 00 11/2004 429
18
Quantum I/O Modules
At a Glance
Introduction The following section provides information on the Quantum input/output (I/O)
modules.
What’s in this
Chapter?
This chapter contains the following sections:
Section Topic Page
18.1 Overview of I/O Modules 430
18.2 Analog Input Modules 444
18.3 Analog Output Modules 477
18.4 Analog Input/Output Modules 493
18.5 Discrete Input Modules 504
18.6 Discrete Output Modules 556
18.7 Discrete Verified Output Module 619
18.8 Discrete Supervised Input Module 629
18.9 Discrete Input/Output Modules 634
I/O Modules
430 840 USE 100 00 11/2004
18.1 Overview of I/O Modules
At a Glance
Overview This section provides an overview of I/O modules used in Quantum.
What’s in this
Section?
This section contains the following topics:
Topic Page
Quantum I/O Modules 431
I/O Map Status Byte 442
I/O Modules
840 USE 100 00 11/2004 431
Quantum I/O Modules
Overview The following section contains specifications for input/output modules. Module
descriptions include wiring diagrams, LED indicators and descriptions, illustrations
of module figures, and, for discrete modules, true high/true low descriptions.
I/O Module The following figure shows the I/O modules and its components.
Quantum I/O LED
Descriptions
These tables describe the generic LED blocks used in Quantum I/O modules.
Descriptions of each type I/O modules’ unique LED configuration are included in the
individual I/O module specifications in this section.
When field wiring the I/O modules, the maximum wire size that should be
used on a field wiring terminal is 1-14 AWG or 2-16 AWG; the minimum size is 20
AWG.
The field wiring terminal strip (Modicon #140XTS00200) must be ordered
separately. (The terminal strip includes the removable door and label.)


10 80 vdc out
X X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Removable Door
Customer Identification Label
(Fold label and place it inside the door) Field Wiring
Terminal Strip
Model Number
Module Description
Color Code
LED Area
Fuse
Cutouts
2 3
5
7
9
11
13
15
17
19
23
25
27
29
31
33
35
37
39
1
4
6
8
10
12
14
16
18
24
26
28
30
32
34
36
38
40
2
I/O Modules
432 840 USE 100 00 11/2004
LED Indicators
and Descriptions
for Discrete 16
Point and Analog
I/O Modules
The following table shows the LED indicators for discrete 16 point and analog I/O
modules.
The following table shows the LED descriptions for discrete 16 point and analog I/O
modules.
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red A fault (external to the module) has been detected.
1 ... 16 Green The indicated point or channel is turned ON.
1 ... 16 Red There is a fault on the indicated point or channel.