140CPU11302C模块备件

LED指示器
和描述
对于24点输入
模块
下表显示了24点输入模块的LED指示灯。
下表显示了24点输入模块的LED说明。
LED指示器
和描述
对于32点I/O
模块
下表显示了32点I/O模块的LED指示灯。
下表显示了32点I/O模块的LED说明。
开启时LED颜色指示
存在主动绿色总线通信。
F红色：检测到故障（模块外部）。
1…24绿色指示点或通道打开。
活性F
1 9
2 10
3 11
4 12
5.
6.
7.
8.
13
14
15
16
17
18
19
20
21
22
23
24
开启时LED颜色指示
存在主动绿色总线通信。
F红色：检测到故障（模块外部）。
1…32绿色指示点或通道打开。
活性F
1 9
2 10
3 11
4 12
5.
6.
7.
8.
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
I/O模块
434840使用100 00 2004年11月
LED指示器
和描述
用于双向
模块
下表显示了140AMM09000双向LED指示灯
单元
下表显示了140AMM09000双向LED的说明
单元
下表显示了140DAM5900和的LED指示灯
140DDM3900双向模块。
开启时LED颜色指示
存在主动绿色总线通信。
F红色：输出组或输入超出范围未通电。
1和2（左列）绿色表示输出处于活动状态。
1和2（中间
专栏）
红色表示输出状态：断线或磁场供电不良。
1…4（右栏）红色表示输入状态：低于/超过范围。
活性F
1 1
2 2
1.
2.
3.
4.
活性F
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.
7.
8.
9
10
11
12
13
14
15
16
I/O模块
840使用100 00 11/2004 435
下表显示了140DAM5900和的LED说明
140DDM3900双向模块。
下表显示了140DDM69000双向LED指示灯
单元
下表显示了140DDM69000双向LED的说明
模块。
开启时LED颜色指示
存在主动绿色总线通信。
F红色：检测到故障（模块外部）。
1和8（左列）绿色指示的输出点和通道打开。
1和16（右两列）绿色指示的输入点和通道打开。
开启时LED颜色指示
存在主动绿色总线通信。
F在任何点上的过电流条件。
1和4（左列）绿色指示的输出点打开。
1和4（中间列）红色指示的输出点具有过电流条件。
1和4（右列）绿色指示的输入点打开。
活性F
1 1 1
2 2 2
3 3 3
4 4 4
I/O模块
436 840使用100 00 11/2004
LED指示器
和描述
对于离散12
点模
过失
指示
下表显示了离散12点的LED指示灯
带故障指示的140DDO88500模块。
下表显示了离散12点模块的LED说明，其中：
故障指示。
现场接线
端子排/
模块键控
作业
现场接线端子板和模块外壳在左右两侧开槽
PCB卡插槽的侧面，用于接收键控引脚（参见I/O模块图）。这个
键控的目的是防止将端子排插入错误的模块，
一旦完成接线连接。键控由用户自行决定
用户的。
主钥匙位于模块右侧，标记为A至F（顶部
底部位置编码相同）。主键控提供模块类
编码。主要代码已预定义（见下表）。
开启时LED颜色指示
存在主动绿色总线通信。
F红色：检测到任何点的过流情况。
1…12绿色指示点或通道打开。
1…12红色指示的输出点具有过电流状态。
活性F
1 9 1
2 10 2
3 11 3
4 12 4
9
10
11
12
5.
6.
7.
8.
5.
6.
7.
8.



为了实现大的安全和保护，Modicon建议使用模块密钥编码
作为系统安装程序的一部分。








 !"#
I/O模块
840使用100 00 11/2004 437
辅助钥匙设置在模块左侧，标记为1至6。
辅助键控代码可由用户定义，可用于识别模块
模块类内的个性或其他独特的现场要求。
下图显示了I/O模块键控分配。
为了支持键控，所有接受端子排的I/O模块都配有12个可定制的主键（模块和端子排各有6个黄色键），以及
六个辅助键（模块和端子排各有三个白色键）。在
下表，检查主模块和端子排编码列
关键位置。LED Indicators
and Descriptions
for 24 Point Input
Modules
The following table shows the LED indicators for the 24 point input modules.
The following table shows the LED descriptions for the 24 point input modules.
LED Indicators
and Descriptions
for 32 Point I/O
Modules
The following table shows the LED indicators for the 32 point I/O modules.
The following table shows the LED descriptions for the 32 point I/O modules.
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red A fault (external to the module) has been detected.
1 ... 24 Green The indicated point or channel is turned ON.
Active F
1 9
2 10
3 11
4 12
5
6
7
8
13
14
15
16
17
18
19
20
21
22
23
24
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red A fault (external to the module) has been detected.
1 ... 32 Green The indicated point or channel is turned ON.
Active F
1 9
2 10
3 11
4 12
5
6
7
8
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
I/O Modules
434 840 USE 100 00 11/2004
LED Indicators
and Descriptions
for Bi-Directional
Modules
The following table shows the LED indicators for the 140AMM09000 bi-directional
module.
The following table shows the LED descriptions for the 140AMM09000 bi-directional
module.
The following table shows the LED indicators for the 140DAM59000 and
140DDM39000 bi-directional modules.
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red No power applied to the output group(s) or input out-ofrange.
1 and 2 (left column) Green Indicates output is active.
1 and 2 (middle
column)
Red Indicates output status: broken wire or bad field supply.
1 ... 4 (right column) Red Indicates input status: under/over range.
Active F
1 1
2 2
1
2
3
4
Active F
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
I/O Modules
840 USE 100 00 11/2004 435
The following table shows the LED descriptions for the 140DAM59000 and
140DDM39000 bi-directional modules.
The following table shows the LED indicators for the 140DDM69000 bi-directional
module.
The following table shows the LED descriptions for the 140DDM69000 bi-directional
modules.
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red A fault (external to the module) has been detected.
1 and 8 (left columns) Green The indicated output point and channel is turned ON.
1 and 16 (right two columns) Green The indicated input point and channel is turned ON.
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red Over current condition on any point.
1 and 4 (left columns) Green The indicated output point is turned ON.
1 and 4 (middle columns) Red The indicated output point has an over current condition.
1 and 4 (right columns) Green The indicated input point is turned ON.
Active F
1 1 1
2 2 2
3 3 3
4 4 4
I/O Modules
436 840 USE 100 00 11/2004
LED Indicators
and Descriptions
for Discrete 12
Point Modules
with Fault
Indication
The following table shows the LED indicators for the discrete 12 point
140DDO88500 module with fault indication.
The following table shows the LED descriptions for discrete 12 point modules with
fault indication.
Field Wiring
Terminal Strip/
Module Keying
Assignments
Field wiring terminal strips and module housings are slotted on the left and right
sides of the PCB card slot to accept keying pins (see I/O Module figure). The
purpose of keying is to prevent plugging the terminal strip into the wrong module,
once wiring connections have been made. Keying is implemented at the discretion
of the user.
Primary keying is provided on the right side of the module, marked A through F (top
and bottom positions are coded the same). Primary keying provides module class
coding. Primary codes have been pre-defined (see the following chart).
LEDs Color Indication when ON
Active Green Bus communication is present.
F Red An over current condition on any point has been detected.
1 ... 12 Green The indicated point or channel is turned ON.
1 ... 12 Red The indicated output point has an over current condition.
Active F
1 9 1
2 10 2
3 11 3
4 12 4
 9
10
11
12
5
6
7
8
5
6
7
8
    



For maximum safety and protection, Modicon recommends that module key coding
be part of the system installation procedure.








 !"#
I/O Modules
840 USE 100 00 11/2004 437
Secondary keying is provided on the left side of the module, marked 1 through 6.
Secondary keying codes are user-definable and may be used to identify module
personality within module classes, or other unique site requirements.
The following figure shows the I/O module keying assignments.
To support keying, all I/O modules accepting terminal strips come with 12 customerinstallable primary keys (six yellow keys each for the module and terminal strip) and
six secondary keys (three white keys each for the module and terminal strip). In the
following table, check the Primary Module and Terminal Strip Coding columns for
key locations.
The primary/secondary keys shown (in black) in this example reflect the
recommended coding of a 24 Vdc module in slot 6 to its field wiring terminal strip.
X
    

    


Secondary
Key Slots
Primary
Key Slots
        

    




























    




Install the key into the
slot round end first.
1
2
3
4
I/O Modules
438 840 USE 100 00 11/2004
I/O Module
Terminal Strip
Keying
The following table shows the primary module and terminal strip keying for the I/O
modules.
Primary Module and Terminal Strip Keying
Module Class Module Part Number Module Coding Terminal Strip Coding
5 Vdc 140DDI15310 ABC DEF
140DDO15310
9 ... 12 Vdc Unassigned ABD CEF
24 Vdc 140DDI35300 ABE CDF
140DDI35310
140DDM39000
140DDO35300
140DDO35310
140DSI35300
140HLI34000
10 ... 60 Vdc 140DDI84100 ABF CDE
140DDI85300
140DDO84300
140DVO85300
125 Vdc 140DDI67300 ACD BEF
140DDM69000
140DDO88500
24 Vac 140DAI34000 ACE BDF
140DAI35300
48 Vac 140DAI44000 ACF BDE
140DAI45300
140DAO84220
115 Vac 140DAI54000 ADE BCF
140DAI54300
140DAI53300
140DAM59000
140DAO84010
230 Vac 140DAI74000 ADF BCE
140DAO84000
140DAO84210
140DRA84000
I/O Modules
840 USE 100 00 11/2004 439
To implement the user-optional secondary keying code (designed to prevent the
mismatching of terminal strips to I/O modules of identical type), 17 slot positions
have been provided in modules and terminal strips to support a variety of coding
schemes.
In addition (by using the secondary keying code), the user may key the field wiring
terminal to the position where the module is installed in a backplane, using the white
keys for each code. To determine a unique module code and terminal strip code,
refer to the table below.
Relay 140DRC83000 AEF BCD
Analog I/O 140ACI03000 BCD AEF
140AVI03000
140ACO02000 BCE ADF
140AVO02000 BCF ADE
TC/RTD 140ARI03010 BDE ACF
140ATI03000
Analog In/Out 140AMM09000 BDF ACE
Intelligent/
Special Purpose
140EHC10500 BEF ACD
140EHC20200
Unassigned CDE ABF
Unassigned CDF ABE
Unassigned CEF ABD
Unassigned DEF ABC