140CPU31110C模块备件

他的模块需要九个连续的16位（3x）寄存器，八个用于输入数据，以及
一个用于输入状态。数据寄存器格式如下：
寄存器1通道1数据
寄存器2
寄存器3
寄存器4
通道2数据
通道3数据
通道4数据
寄存器5通道5数据
寄存器6
寄存器7
寄存器8
信道6数据
通道7数据
通道8数据
     
    

1=通道5上的断线或超出范围
1=通道6上的断线或超出范围
1=通道7上的断线或超出范围
1=通道8上的断线或超出范围
1234567 8 9 10 11 12 13 14 15 16
1=通道8上的范围警告*
1=通道7上的范围警告*
1=通道6上的范围警告*
1=通道5上的范围警告*
1=通道1上的断线或超出范围
1=通道2上的断线或超出范围
1=通道3上的断线或超出范围
1=通道4上的断线或超出范围
1=通道4上的范围警告*
1=通道3上的范围警告*
1=通道2上的范围警告*
1=通道1上的范围警告*
I/O模块
450 840使用100 00 2004年11月
*当通道输入超过额定输入值时，会发出范围警告。一
当通道输入超过额定输入值2.34%时，设置超出范围位
或者当在通道上感测到断线时。警告位在以下情况下清除：
设置超出范围位。
I/O映射状态
字节
140ARI03010输入模块使用I/O映射状态字节，如下所示：
Modsoft模块
缩放选择
按下＜Enter＞以显示和选择整个模块和通道配置。
数据格式为正范围内的16位整数值和一个整数
MSB指示负范围中的负号的值。
通道1超出范围或短路
8 7 6 5 4 3 2 1
MSB LSB
通道2超出范围或短路
通道3超出范围或短路
通道4超出范围或短路
通道5超出范围或短路
通道6超出范围或短路
通道7超出范围或短路
通道8超出范围或短路
1.0度
0.1度
摄氏度
华氏度
温度
原值
决议：
输出单元：
值类型：
I/O模块
840使用100 00 11/2004 451
下图显示了通道X配置选择。
140ATI03000以下信息与140ATI00000模拟输入的配置有关
单元
使能
禁用
Pt100，-200…850
Pt200，-200…850
Pt500，-200…850
Pt1000，-200…850
Ni100，-60…180
Ni200，-60…180
Ni500，-60…180
Ni1000，-60…180
R、 0…766.66欧姆
R、 0…4000欧姆
APt100，-100…450
APt200，-100…450
APt500，-100…450
APt1000，-100…450
电阻式温度检测器类型（铂、镍、铂、铂）：
4线/3线/2线：
信道启用/禁用：
4线
3线
双线
I/O模块
452 840使用100 00 2004年11月
I/O映射寄存器
作业
该模块需要十个连续的16位字，八个用于输入数据，一个用于
通道状态，一个用于模块的内部温度。数据字
格式如下。
字1信道1数据
单词2
单词3
单词4
通道2数据
通道3数据
通道4数据
字5信道5数据
单词6
单词7
单词8
信道6数据
通道7数据
通道8数据
I/O模块
840使用100 00 11/2004 453
下面显示了字9寄存器。
*当通道输入超过额定输入值时，会发出量程警告，如
如下表所示。当通道输入超过时，设置超出范围位
额定输入值增加2.4%，或在通道上检测到断线时。这个
当设置超出范围位时，警告位被清除。
下图显示了字10寄存器。
             
1=通道5超出范围
1=通道6超出范围
1=通道7超出范围
1=通道8超出范围
1234567 8 9 10 11 12 13 14 15 16
1=通道8上的范围警告*
1=通道7上的范围警告*
1=通道6上的范围警告*
1=通道5上的范围警告*
1=通道1超出范围
1=通道2超出范围
1=通道3超出范围
1=通道4超出范围
1=通道4上的范围警告*
1=通道3上的范围警告*
1=通道2上的范围警告*
1=通道1上的范围警告*
字10内部温度
I/O模块
454840使用100 00 2004年11月
I/O映射状态
字节
I/O映射状态字节由140ATI03000输入模块使用，如下所示。
测量
范围
下表中的范围以摄氏度表示。用户可以选择：
输出数据格式为0.1或1.0°（C或F）。
如果选择0.1°格式，则表示小数点（即读数为1234
应解释为123.4°）。内部CJC数据以相同单位报告
作为TC输出
所有TC输出数据均为有符号整数格式，但B型除外（见下文）。
通道1断路或超出范围
8 7 6 5 4 3 2 1
MSB LSB
通道2断路或超出范围
通道3断路或超出范围
通道4断路或超出范围
通道5断路或超出范围
通道6断路或超出范围
通道7断路或超出范围
第8频道操作his module requires nine contiguous 16-bit (3x) registers—eight for input data and
one for input status. The data registers formats are as follows:
Register 1 Channel 1 data
Register 2
Register 3
Register 4
Channel 2 data
Channel 3 data
Channel 4 data
Register 5 Channel 5 data
Register 6
Register 7
Register 8
Channel 6 data
Channel 7 data
Channel 8 data
     
    

1 = Broken wire or out range on channel 5
1 = Broken wire or out range on channel 6
1 = Broken wire or out range on channel 7
1 = Broken wire or out range on channel 8
1234567 8 9 10 11 12 13 14 15 16
1 = Range warning on channel 8*
1 = Range warning on channel 7*
1 = Range warning on channel 6*
1 = Range warning on channel 5*
1 = Broken wire or out range on channel 1
1 = Broken wire or out range on channel 2
1 = Broken wire or out range on channel 3
1 = Broken wire or out range on channel 4
1 = Range warning on channel 4*
1 = Range warning on channel 3*
1 = Range warning on channel 2*
1 = Range warning on channel 1*
I/O Modules
450 840 USE 100 00 11/2004
*A range warning is issued when a channel input exceeds the rated input value. An
out-of-range bit is set when a channel input exceeds the rated input value by 2.34%
or when a broken wire is sensed on the channel. The warning bit is cleared when
the out-of-range bit is set.
I/O Map Status
Byte
The I/O map status byte is used by the 140ARI03010 Input module as follows:
Modsoft Module
Zoom Selections
Push <Enter> to display and select the overall module and channel configuration.
The data format is 16-bit integer values in the positive range and an integer
value with the MSB indicating a negative sign in the negative range.
Channel 1 out of range or short circuit
8 7 6 5 4 3 2 1
MSB LSB
Channel 2 out of range or short circuit
Channel 3 out of range or short circuit
Channel 4 out of range or short circuit
Channel 5 out of range or short circuit
Channel 6 out of range or short circuit
Channel 7 out of range or short circuit
Channel 8 out of range or short circuit
1.0 DEG
0.1 DEG
CELSIUS
FAHRENHEIT
TEMPERATURE
RAW VALUE
Resolution:
Output unit:
Value Type:
I/O Modules
840 USE 100 00 11/2004 451
The following figure shows the channel X configuration selection.
140ATI03000 The following information pertains to configuration of the 140ATI03000 Analog Input
module.
ENABLE
DISABLE
Pt100, -200 ...850
Pt200, -200 ...850
Pt500, -200 ...850
Pt1000, -200 ...850
Ni100, -60 ... 180
Ni200, -60 ... 180
Ni500, -60 ... 180
Ni1000, -60 ... 180
R, 0 ... 766.66 OHM
R, 0 ... 4000 OHM
APt100, -100 ... 450
APt200, -100 ... 450
APt500, -100 ... 450
APt1000, -100 ... 450
RTD TYPE (Pt, Ni, R, A Pt):
4-Wire/3-Wire/2-Wire:
Channel Enable/Disable:
4 WIRE
3 WIRE
2-WIRE
I/O Modules
452 840 USE 100 00 11/2004
I/O Map Register
Assignments
This module requires ten contiguous, 16-bit words—eight for input data, one for
channel status, and one for internal temperature of the module. The data words
formats are as follows.
Word 1 Channel 1 data
Word 2
Word 3
Word 4
Channel 2 data
Channel 3 data
Channel 4 data
Word 5 Channel 5 data
Word 6
Word 7
Word 8
Channel 6 data
Channel 7 data
Channel 8 data
I/O Modules
840 USE 100 00 11/2004 453
The following shows the word 9 register.
* A range warning is issued when a channel input exceeds the rated input value, as
shown in the following table. An out-of-range bit is set when a channel input exceeds
the rated input value by 2.4% or when a broken wire is sensed on the channel. The
warning bit is cleared when the out-of-range bit is set.
The following figure shows the word 10 register.

             
1 = Channel 5 out of range
1 = Channel 6 out of range
1 = Channel 7 out of range
1 = Channel 8 out of range
1234567 8 9 10 11 12 13 14 15 16
1 = Range warning on channel 8*
1 = Range warning on channel 7*
1 = Range warning on channel 6*
1 = Range warning on channel 5*
1 = Channel 1 out of range
1 = Channel 2 out of range
1 = Channel 3 out of range
1 = Channel 4 out of range
1 = Range warning on channel 4*
1 = Range warning on channel 3*
1 = Range warning on channel 2*
1 = Range warning on channel 1*
Word 10 Internal temperature
I/O Modules
454 840 USE 100 00 11/2004
I/O Map Status
Byte
The I/O map status byte is used by the 140ATI03000 Input Module as follows.
Measurement
Ranges
Ranges in the following table are expressed in degrees C. The user can select either
0.1 or 1.0° (C or F) for the output data format.
If the 0.1° format is selected, the decimal point is implied (i.e., a reading of 1234
should be interpreted as 123.4°). The internal CJC data is reported in the same units
as the TC output
All TC output data is in signed integer format except as noted for Type B (see below).
Channel 1 open circuit or out of range
8 7 6 5 4 3 2 1
MSB LSB
Channel 2 open circuit or out of range
Channel 3 open circuit or out of range
Channel 4 open circuit or out of range
Channel 5 open circuit or out of range
Channel 6 open circuit or out of range
Channel 7 open circuit or out of range
Channel 8 open circuit or out of range
If the TC is open, then the warning bit is cleared and the out-of-range bit is
set. If it is over range, then the channel’s output data word is always 7FFFH; if it is
under range, the channel’s output data word is always 8001H. These are the
possible highest and lowest values.
I/O Modules
840 USE 100 00 11/2004 455
Measurement
Range Tables
This table shows thermocouple ranges.
This table shows millivolt ranges.
Thermocouple Ranges
Data
Format
Input Minimum
Reading
Normal Over Range
Warning
Out-ofRange Set
Modsoft
Signed
Format
J Type TC -228.5 -210 to +760 760.1 to 778.6 >778.7
K Type TC -302.9 -270 to +1370 1370.1 to 1405.0 >1405.1
E Type TC -293.8 -270 to +1000 1000.1 to 1023.9 >1024.0
T Type TC -279.5 -270 to +400 400.1 to 409.6 >409.7
S Type TC -89.9 -50 to +1665 1665.1 to 1705.0 >1705.1
R Type TC -89.6 -50 to +1665 1665.1 to 1704.7 >1704.8
B Type TC
(See Note 3)
+86.4 +130 to +1820 1820.1 to 1863.7 >1863.8
Millivolt Ranges
Offset
Binary
-100 mV
0
+ 100 mV
Gain = 25
0
0
8000h
FFFFh
None See Note 2
-25 mV
0
+25 mV
Gain = 100
0
0
8000h
FFFFh
None See Note 2

$ Open Circuit Detect is always enabled for all TC types and may be disabled for
linear ranges.
% On millivolt ranges, if Open Circuit Detect is enabled, this bit is set on Open
Circuit Detect or input FFFFh
& Data format changes to unsigned if the output is requested in units of 0.1° F to
accommodate readings above 3276.8° F.
I/O Modules
456 840 USE 100 00 11/2004
Module Zoom
Selections
Push <Enter> to display and select the configuration parameters.
1.0 DEG
0.1 DEG
CENTIGRADE
FAHRENHEIT
On board
Channel 1
Undefined
J, gain=25
K, gain=25
E, gain=25
T, gain=100
S, gain=100
R, gain=100
B, gain=100
NO
YES
25
100
NO
YES
Resolution:
Output Unit:
Cold Junction Compensator:
CHANNEL X CONFIGURATION
Thermocouple Type:

Undefined = Linear Range
The next two entries are for undefined type:
Open Circuit Test:
Millivolt Range:
This channel installed
I/O Modules
840 USE 100 00 11/2004 457
140AVI03000 The following information pertains to configuration of the 140AVI03000 Analog Input
module.
I/O Map Register
Assignments
This module requires nine contiguous input (3x) registers.
Map Register
Assignment
The following figures shows the assignment registers and the input sta