140CPU53414B模块备件

下表显示了模拟输入/输出的输出规格
单元
输出规格
回路电压7…30 Vdc，高达60 Vdc，带外部电阻器
环路电阻
20 mA时内部电压降小为7 Vdc，大为30 Vdc
分辨率（位）12
25°C下的精度误差+/-0.20%满刻度
线性单调+/-1 LSB
精度误差0…60°C典型值：满刻度+/-0.004%/°C。
大值：满量程的+/-0.007%/°C
隔离
通道至通道500 Vac，750 Vdc，持续1分钟
通道至总线500 Vac，750 Vdc，持续1分钟
输出通道到输入
频道
500 Vac，750 Vdc，持续1分钟
2个信道的更新时间：15毫秒
沉降时间：900μs至终值的+/-0.1%
故障检测、断路指示灯和状态字节
外部电源：参见上面的回路电压
RMIN∗ Vloop–30Vdc
0,02A=------------------------------------
RMAX
Vloop–7Vdc
0,02A=---------------------------------
*循环不需要RMIN
电压低于30 Vdc。
I/O模块
840使用100 00 11/2004 501
电压表
班长
规格
下表显示了模拟电压表监视器的规格
输入/输出模块。
常见的
规格
下表显示了模拟输入/输出的常见规格
单元
电压表监视器规格
范围1…5 V（回路电流必须激活）
缩放IOUT（mA）x 0.250=VOUT（伏特）
输出阻抗300Ω典型值
大电线长度1米
通用规格
要求寻址：5字入2字出
所需总线电流（模块）350 mA
融合
内部：无需
外部用户自由裁量权
I/O模块
502 840使用100 00 2004年11月
接线图：下图显示了140AMM09000模拟输入的接线图/
输出模块。
2.
4.
6.
8.
12
14
16
18
20 19
17
15
13
11
9
7.
5.
3.
1.
22
24
26
28
30
32
34
36
38
40 39
37
35
33
31
29
27
25
23
21
电流源（-）1
电流源（-）1
N/C
N/C
电流源（-）1
电流源（-）2
电流源（-）2
N/C
N/C
电流源（-）2
在（-）1中
N/C
在（-）2中
N/C
N/C
在（-）3中
N/C
在（-）4中
N/C
N/C N/C
感觉4
在（+）4中
感觉3
在（+）3中
N/C
感觉2
在（+）2中
意义1
电流吸收器（+）2
N/C
N/C
N/C
监视器2
电流吸收器（+）1
N/C
N/C
N/C
监视器1+–
可选监视器
电压表
1 V=4 mA
5 V=20 mA 24 Vdc
领域
供给
领域
装置
领域
装置
4-20mA
现在的
4-20mA
现在的
在（+）1中
–
+传感器
0-10V
输出
+
_
10
五、
I/O模块
840使用100 00 11/2004 503
以下信息与上述接线图有关。
输出部分2通道
输入部分4通道
典型接线输出
通道1输出显示与外部现场设备和可选监视器的连接。
通道2：输出显示与外部现场设备的连接，以及
频道1。
典型接线输入
通道1通道1显示由输出部分通道2控制的4-20 mA电流输入。
通道4输入显示与电压输出传感器的连接。

$引脚1…20为输出
引脚21…40是输入
%N/C=未连接
&所有电流输入的输入（+）和感测端子之间需要跳线
范围。
I/O模块
504 840使用100 00 2004年11月
18.5离散输入模块
一瞥
概述本节提供有关量子离散输入模块的信息。
这是什么
部分
本节包含以下主题：
主题页
离散输入模块505的I/O配置
模块509中的140DAI34000量子I/O 24 VAC
140DAI35300量子输入/输出交流输入24 Vac模块512
模块515中的140DAI44000量子I/O 48 VAC
140DAI45300量子I/O AC输入48 Vac 4x8模块518
模块521中的140DAI54000量子I/O 115 VAC
140DAI54300量子输入/输出交流输入115 Vac 2x8模块524
140DAI55300量子输入/输出交流输入115 Vac 4x8模块527
140DAI74000量子I/O AC输入230 Vac 16x1模块530
140DAI75300量子输入/输出交流输入230 Vac 4x8模块533
140DDI15310量子I/O直流输入5V TTL 4x8源模块536
140DDI35300量子输入/输出直流输入24 Vdc 4x8接收器模块538
140DDI35310量子I/O DC输入24 Vdc真低4x8输入模块540
140DDI36400输入/输出直流输入24 VDC 6x16远程快速输入模块542
140DDI67300量子I/O DC输入125 Vdc 3x8接收器模块546
140DDI84100量子输入/输出直流输入10…60 Vdc 8x2接收器模块550
140DDI85300量子输入/输出直流输入10…60 Vdc 4x8接收器模块553
I/O模块
840使用100 00 11/2004 505
离散输入模块的I/O配置
概述本节提供关于16、24、32和96点输入配置的信息
模块。
16点输入
模块
16点输入模块包括：
140DAI34000（交流输入24 Vac 16x1）
140DAI44000（交流输入48 Vac 16x1）
140DAI54000（交流输入115 Vac 16x1）
140DAI54300（交流输入115 Vac 8x2）
140DAI74000（交流输入230 Vac 16x1）
140DDI84100（直流输入10…60 Vdc 8x2接收器）
I/O映射寄存器
分配
上述输入模块可配置为16个连续1x
参考或作为一个3x寄存器。下图显示了16点寄存器。
I/O映射状态
字节
没有I/O映射状态字节assocThe following table shows the output specifications for the analog input/output
module.
Output Specifications
Loop Voltage 7 ... 30 Vdc, up to 60 Vdc with an external resistor
Loop Resistance
Internal Voltage Drop 7 Vdc min, 30 Vdc max @ 20 mA
Resolution (bits) 12
Accuracy Error @ 25° C +/- 0.20% of full scale
Linearity Monotonic +/- 1 LSB
Accuracy Error 0 ... 60° C Typical: +/- 0.004%/°C of full scale.
Maximum:+/- 0.007%/°C of full scale
Isolation
Channel to Channel 500 Vac, 750 Vdc, for 1 minute
Channel to Bus 500 Vac, 750 Vdc, for 1 minute
Output Channel to Input
Channel
500 Vac, 750 Vdc, for 1 minute
Update Time 15 ms for 2 channels
Settling Time 900 μs to +/- 0.1% of final value
Fault Detection Open circuit indicator light and status byte
External Power Supply See loop voltage above
RMIN∗ Vloop – 30Vdc
0,02A = ------------------------------------
RMAX
Vloop – 7Vdc
0,02A = ---------------------------------
*No RMIN is required for loop
voltage less than 30 Vdc.
I/O Modules
840 USE 100 00 11/2004 501
Voltmeter
Monitor
Specifications
The following table shows the specifications for the voltmeter monitor for the analog
input/output module.
Common
Specifications
The following table shows the common specifications for the analog input/output
module.
Voltmeter Monitor Specifications
Range 1 ... 5 V (Loop current must be active)
Scaling IOUT (mA) x 0.250 = VOUT (volts)
Output Impedance 300Ω typical
Maximum Wire Length 1 meter
Common Specifications
Required Addressing 5 Words In 2 Words Out
Bus Current Required (module) 350 mA
Fusing
Internal None required
External User discretion
I/O Modules
502 840 USE 100 00 11/2004
Wiring Diagram The following figure shows the wiring diagram for the 140AMM09000 analog input/
output module.
2
4
6
8
12
14
16
18
20 19
17
15
13
11
9
7
5
3
1
22
24
26
28
30
32
34
36
38
40 39
37
35
33
31
29
27
25
23
21
CURRENT SOURCE(-)1
CURRENT SOURCE(-)1
N/C
N/C
CURRENT SOURCE(-)1
CURRENT SOURCE(-)2
CURRENT SOURCE(-)2
N/C
N/C
CURRENT SOURCE(-)2
IN(-)1
N/C
IN(-)2
N/C
N/C
IN(-)3
N/C
IN(-)4
N/C
N/C N/C
SENSE 4
IN(+)4
SENSE 3
IN(+)3
N/C
SENSE 2
IN(+)2
SENSE 1
CURRENT SINK(+)2
N/C
N/C
N/C
MONITOR 2
CURRENT SINK(+)1
N/C
N/C
N/C
MONITOR 1 + –
Optional Monitor
Voltmeter
1 V= 4 mA
5 V= 20 mA 24 Vdc
Field
Supply
 Field
Device
 Field
Device
4 - 20 mA
Current
4 - 20 mA
Current
IN(+)1
–
+ Sensor
0 - 10 V
Output
+
_
10
V
I/O Modules
840 USE 100 00 11/2004 503
The following information pertains to the wiring diagram above.
Output Section 2 Channels
Input Section 4 Channels
Typical Wiring Outputs
Channel 1 The output shows a connection to an external field device and optional monitor.
Channel 2 The output shows a connection to an external field device and the input of
channel 1.
Typical Wiring Inputs
Channel 1 Channel 1 shows 4 - 20 mA current input controlled by output section Channel 2.
Channel 4 The input shows a connection to a voltage output sensor.

$ Pins 1 ... 20 are outputs
Pins 21 ... 40 are inputs
% N / C = Not Connected
& Jumpers are required between IN (+) and SENSE terminals for all current input
ranges.
I/O Modules
504 840 USE 100 00 11/2004
18.5 Discrete Input Modules
At a Glance
Overview This section provides information on Quantum discrete input modules.
What’s in this
Section?
This section contains the following topics:
Topic Page
I/O Configuration for Discrete Input Modules 505
140DAI34000 Quantum I/O 24 VAC IN Module 509
140DAI35300 Quantum I/O AC Input 24 Vac Module 512
140DAI44000 Quantum I/O 48 VAC IN Module 515
140DAI45300 Quantum I/O AC Input 48 Vac 4x8 Module 518
140DAI54000 Quantum I/O 115 VAC In Module 521
140DAI54300 Quantum I/O AC Input 115 Vac 2x8 Module 524
140DAI55300 Quantum I/O AC Input 115 Vac 4x8 Module 527
140DAI74000 Quantum I/O AC Input 230 Vac 16x1 Module 530
140DAI75300 Quantum I/O AC Input 230 Vac 4x8 Module 533
140DDI15310 Quantum I/O DC Input 5 V TTL 4x8 Source Module 536
140DDI35300 Quantum I/O DC Input 24 Vdc 4x8 Sink Module 538
140DDI35310 Quantum I/O DC Input 24 Vdc True Low 4x8 Input Module 540
140DDI36400 I/O DC Input 24 VDC 6x16 Telefast Input Module 542
140DDI67300 Quantum I/O DC Input 125 Vdc 3x8 Sink Module 546
140DDI84100 Quantum I/O DC Input 10 ... 60 Vdc 8x2 Sink Module 550
140DDI85300 Quantum I/O DC Input 10 ... 60 Vdc 4x8 Sink Module 553
I/O Modules
840 USE 100 00 11/2004 505
I/O Configuration for Discrete Input Modules
Overview This section provides information on configuration of 16-, 24-, 32-, and 96-point input
modules.
16-Point Input
Modules
The 16-point input modules are:
 140DAI34000 (AC Input 24 Vac 16x1)
 140DAI44000 (AC Input 48 Vac 16x1)
 140DAI54000 (AC Input 115 Vac 16x1)
 140DAI54300 (AC Input 115 Vac 8x2)
 140DAI74000 (AC Input 230 Vac 16x1)
 140DDI84100 (DC Input 10 ... 60 Vdc 8x2 Sink)
I/O Map Register
Assignment
The input modules listed above can be configured as either 16 contiguous 1x
references or as one 3x register.The following figure shows the 16-point register.

I/O Map Status
Byte
There is no I/O map status byte associated with these modules.
Modsoft Module
Zoom Selections
Push <Enter> to display and select the input type. This selection appears if the
module is I/O mapped to a 3x register. The following figure shows the input type
display.

24-Point Input
Module
There is only one 24-point input module: 140 DDI 673 00 (DC Input 125 VDC 3x8
Sink).
1234567 8 9 10 11 12 13 14 15 16
BIN
BCD
input
I/O Modules
506 840 USE 100 00 11/2004
I/O Map Register
Assignment
The input module listed above can be configured as either 24 contiguous discrete
input (1x) reference, or as two contiguous input (3x) registers in the following format.
The following figures show the input point for Register 1 and Register 2.

I/O Map Status
Byte
There is no input I/O map status byte associated with this module.
Modsoft Module
Zoom Selections
Push <Enter> to display and select the Input Type and the Filter Select options. The
following figures show the input type and the filter select option.

32-Point Input
Modules
The 32-point input modules are as follows:
 140DAI35300 (AC Input 24 Vac 4x8)
 140DAI45300 (AC Input 48 Vac 4x8)
 140DAI55300 (AC Input 115 Vac 4x8)
 140DAI75300 (AC Input 230 Vac 4x8)
 140DDI15310 (DC Input 5 V TTL 4x8 Source)
 140DDI35300 (DC Input 24 Vdc 4x8 Sink)
 140DDI35310 (DC Input 24 Vdc 4x8 Source)
 140DDI85300 (DC Input 10 ... 60 Vdc 4x8 Sink)
1234567 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Register 1
Input
Point 1
MSB - First Word
Register 2
Input
Point 17
MSB - Second Word
BIN
BCD
.7 msec
1.5 msec
Group X
Filter Select on:
Input Type: The input Type selection only appears
if the module is I/O mapped to a 3x register.
The Filter Select option is made on a
group-by-group basis and defaults to the .7 msec
I/O Modules
840 USE 100 00 11/2004 507
I/O Map Register
Assignment
The input modules listed above can be configured as either 32 contiguous discrete
input (1x) references or as two contiguous input (3x) registers in the following format.
The following figure shows the input points for Register 1 and Register 2.

I/O Map Status
Byte
There is no I/O map status byte associated with these modules.
Modsoft Module
Zoom Selections
Push <Enter> to display and select the input type. This selection appears if the
module is I/O mapped to a 3x register. The following figure shows the input type.

96-Point Input
modules
The following is the only 96 point input module:
 140DDI36400 - DC input 6 x 16 sink
1234567 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Register 1
Input
Point 1
MSB - First Word
Register 2
Input
Point 17
MSB - Second Word
BIN
BCD
Input Type
I/O Modules
508 840 USE 100 00 11/2004
140DDI36400
Register
Assignment
The following information pertains to the 140DDI36400 Input module. The following
figures show the output points for register 1 through 6.

I/O Map Status
Byte
There is no I/O map status byte associated with this module.
Modsoft Module
Zoom Selections
Push <Enter> to display and select the input type. This selection appears if the
module is I/O mapped to a 3x register. The following figure shows the input type.

1234567 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Register 1
Input
Point 1
MSB - First Word
Register 2
Input
Point 17
MSB - Second Word
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Register 3
Input
Point 33
MSB - Third Word
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Register 4
Input
Point 49
MSB - Fourth Word
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Register 5
Input
Point 65
MSB - Fifth Word
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
Register 6
Input
Point 81
MSB - Sixth Word
BIN
BCD
Input Type:
I/O Modules
840 USE 100 00 11/2004 509
140DAI34000 Quantum I/O 24 VAC IN Module
Overview The AC Input 24 Vac 16x1 module accepts 24 Vac inputs. 
I/O Modules
510 840 USE 100 00 11/2004
Specifications The following table shows the specifications for the DAI34000 24 VAC IN module.
Note: Input signals must be sinusoidal with less than 6% THD (Total Harmonic
Distortion) and 63 Hz maximum frequency.
+/-
规格下表显示了
毫伏