140CPU65160C模块备件

本节提供有关量子离散输出模块的信息。
这是什么
部分
本节包含以下主题：
主题页
离散输出模块的I/O配置557
140DAO84000输入/输出交流输出24…230 Vac 16x1模块564
140DAO84010输入/输出交流输出24…115 Vac 16x1模块568
140DAO84210量子输入/输出交流输出100…230 Vac 4x4模块572
140DAO84220量子输入/输出交流输出24…48 Vac 4x4模块577
140DAO85300量子输入/输出交流输出24…230 Vac 4x8模块582
140DDO15310输入/输出直流输出5V TTL 4x8接收器模块586
140DDO35300量子I/O直流输出24 Vdc 4x8源模块590
140DDO35301输入/输出直流输出24 VDC 4x8离散源模块594
140DDO35310输入/输出直流输出24 Vdc 4x8接收器模块597
140DDO36400输入/输出直流输出24VDC 6x16远传输出模块601
140DDO84300量子I/O直流输出10…60 Vdc 2x8电源模块606
140DDO88500量子I/O直流输出24-125 Vdc 2x6电源模块609
140DRA84000量子I/O继电器输出16x1常开模块613
140DRC83000量子I/O继电器输出8x1常开/常开
闭模
616
I/O模块
840使用100 00 11/2004 557
离散输出模块的I/O配置
概述本节提供了关于8点、12点、16点、32点和96点配置的信息
输出模块。
8点输出
模块
以下显示了8点输出模块：
140DRC83000（继电器输出8x1常开/常闭）
I/O映射寄存器
分配
上面列出的输出模块可以配置为八个连续模块
离散输出（0x）引用或作为一个输出（4x）寄存器。下图
显示输出模块的格式。
I/O映射状态
字节
没有与这些模块关联的I/O映射状态字节。
模块缩放
选择
按下＜Enter＞显示并选择模块的输出类型和超时状态。
当模块的系统控制停止时，出现超时状态。
1 2345678
输出类型：
超时状态：
用户定义的超时状态点1-8:00000000
箱子
BCD
后值
用户定义
I/O模块
558 840使用100 00 11/2004
模块缩放
选择
（产出）
按下＜Enter＞以显示并选择输出类型和超时状态
单元当模块的系统控制停止时，假设超时状态。
12点输出
单元
12点输出模块为：
140DDO88500
I/O映射寄存器
分配
（故障输入）
140DDO88500可以配置为16个连续1x引用，也可以配置为
一个3x寄存器。
下图显示了输入配置。
模块缩放
选择
（输入）
按＜Enter＞显示并选择输入类型。如果
模块I/O映射到3x寄存器。下图显示了输入类型。
I/O映射寄存器
分配
（产出）
140DDO88500可配置为以下一个输出（4x）寄存器：
总体安排下图显示了输出的寄存器格式。
箱子
BCD
输出类型：
1234567 8 9 10 11 12
不要使用BCD选项，因为它将错误地显示故障状态。
箱子
BCD
输入类型：
1234567 8 9 10 11 1
I/O模块
840使用100 00 11/2004 559
I/O映射状态
字节（输出）
输出I/O映射状态字节中的低有效位使用如下。这个
下图显示了状态字节输出寄存器。
Modsoft模块
缩放选择
（产出）
按下＜Enter＞以显示并选择输出类型和超时状态
单元当模块的系统控制停止时，假设超时状态。
下图显示了输出类型和超时状态。
16点输出
模块
16点输出模块如下：
140DAO84000（交流输出24…230 Vac 16x1）
140DAO84010（交流输出24…115 Vac 16x1）
140DAO84210（交流输出100…230 Vac 4x4）
140DAO84220（交流输出48 Vac 4x4）
140DDO84300（直流输出10…60 VDC 2x8电源）
140DRA84000（继电器输出16x1常开）
I/O映射寄存器
分配
上面列出的输出模块可以配置为16个连续的或离散的
输出（0x）引用，或作为以下格式的一个输出（4x）寄存器。这个
下图显示了输出模块的格式。
模块故障
（任何点故障都会打开该位。）
8 7 6 5 4 3 2 1
要清除故障，必须在用户逻辑中命令关闭该点。
箱子
BCD
后值
用户定义
超时状态：
输出类型：
用户定义的超时状态点1-12:000000000000
1234567 8 9 10 11 12 13 14 15 16
对于140DAO84000、140DAO8410、140DAO 84210、140DAO84220、140DDO84300，
和140DRA84000 mo
I/O模块
560 840使用100 00 2004年11月
I/O映射状态
字节
I/O映射状态字节由140DAO84210和140DAO8220输出使用
模块。下图显示了使用的I/O映射状态字节。
没有I/O映射状态字节与140DAO84000、140DAO810、140DAO 84000和140DAO8410相关联，
140DDO84300或140DRA84000模块。
模块缩放
选择
按下＜Enter＞以显示并选择输出类型和超时状态This section provides information on Quantum discrete output modules.
What’s in this
Section?
This section contains the following topics:
Topic Page
I/O Configuration for Discrete Output Modules 557
140DAO84000 I/O AC Output 24 ... 230 Vac 16x1 Module 564
140DAO84010 I/O AC Output 24 ... 115 Vac 16x1 Module 568
140DAO84210 Quantum I/O AC Output 100 ... 230 Vac 4x4 Module 572
140DAO84220 Quantum I/O AC Output 24 ... 48 Vac 4x4 Module 577
140DAO85300 Quantum I/O AC Output 24 ... 230 Vac 4x8 Module 582
140DDO15310 I/O DC Output 5 V TTL 4x8 Sink Module 586
140DDO35300 Quantum I/O DC Output 24 Vdc 4x8 Source Module 590
140DDO35301 I/O DC Output 24 VDC 4x8 Discrete Source Module 594
140DDO35310 I/O DC Output 24 Vdc 4x8 Sink Module 597
140DDO36400 I/O DC Output 24VDC 6x16 Telefast Output Module 601
140DDO84300 Quantum I/O DC Output 10 ... 60 Vdc 2x8 Source Module 606
140DDO88500 Quantum I/O DC Output 24-125 Vdc 2x6 Source Module 609
140DRA84000 Quantum I/O Relay Output 16x1 Normally Open Module 613
140DRC83000 Quantum I/O Relay Output 8x1 Normally Open/Normally
Closed Module
616
I/O Modules
840 USE 100 00 11/2004 557
I/O Configuration for Discrete Output Modules
Overview This section provides information on configuration of 8-, 12-, 16-, 32- and 96-point
output modules.
8-Point Output
Modules
The following shows the 8-point output module:
 140DRC83000 (Relay Ouput 8x1 Normally Open/Normally Closed)
I/O Map Register
Assignment
The ouput modules listed above can be configured as either eight contiguous
discrete output (0x) references or as one output (4x) register. The following figure
shows the format for the output modules.

I/O Map Status
Byte
There is no I/O Map status byte associated with these modules.
Module Zoom
Selections
Push <Enter> to display and select the output type and timeout state for the module.
Timeout state isassumed when system control of the module is stopped.
1 2345678
Output Type:
Timeout State:
User Defined Timeout State Points 1- 8: 00000000
BIN
BCD
Last Value
User Define
I/O Modules
558 840 USE 100 00 11/2004
Module Zoom
Selections
(Outputs)
Push <Enter> to display and select the output type and the timeout state for the
module. Timeout state is assumed when sytem control of the module is stopped.
12-Point Output
Module
The 12-point output module is:
 140DDO88500
I/O Map Register
Assignment
(Fault Inputs)
The 140DDO88500 can be configured as either 16 contiguous 1x references or as
one 3x register.
The following figure shows the inputs configuration.
Module Zoom
Selections
(Inputs)
Push <Enter> to display and select the input type. This selection appears if the
module is I/O mapped to a 3x register. The following figure shows the input type.

I/O Map Register
Assignment
(Outputs)
The 140DDO88500 can be configured as one output (4x) register in the following
format. The following figure shows the register format for outputs.

BIN
BCD
Output Type:
1234567 8 9 10 11 12
Do not use the BCD selection, as it will incorrectly display fault conditions.
BIN
BCD
input Type:
1234567 8 9 10 11 1
I/O Modules
840 USE 100 00 11/2004 559
I/O Map Status
Byte (Outputs)
The least significant bit in the output I/O map status byte is used as follows. The
following figure shows the status byte output register.
Modsoft Module
Zoom Selections
(Outputs)
Push <Enter> to display and select the output type and the timeout state for the
module. Timeout state is assumed when system control of the module is stopped.
The following figure shows the output type and timeout state.
16-Point Output
Modules
The 16-point output modules are as follows:
 140DAO84000 (AC Output 24 ... 230 Vac 16x1)
 140DAO84010 (AC Output 24 ... 115 Vac 16x1)
 140DAO84210 (AC Output 100 ... 230 Vac 4x4)
 140DAO84220 (AC Output 48 Vac 4x4)
 140DDO84300 (DC Output 10 ... 60 VDC 2x8 Source)
 140DRA84000 (Relay Output 16x1 Normally Open)
I/O Map Register
Assignment
The output modules listed above can be configured as either 16 contiguous discrete
output (0x) references, or as one output (4x) register in the following formats. The
following figures show the formats for the output modules.

Module Fault
(any point fault turns on this bit)
8 7 6 5 4 3 2 1
To clear a fault, the point must be commanded OFF in user logic.
BIN
BCD
Last Value
User Defined
Timeout State:
Output Type:
User Defined Timeout State Points 1-12: 000000000000
1234567 8 9 10 11 12 13 14 15 16
For the 140DAO84000, 140DAO84010, 140DAO84210, 140DAO84220, 140DDO84300,
and the 140DRA84000 mo
I/O Modules
560 840 USE 100 00 11/2004
I/O Map Status
Byte
The I/O map status byte is used by the 140DAO84210 and 140DAO84220 output
modules. The following figure shows I/O map status bytes use.
There is no I/O map status byte associated with the 140DAO84000, 140DAO84010,
140DDO84300, or 140DRA84000 module.
Module Zoom
Selections
Push <Enter> to display and select the output type and the timeout state for the
module. Timeout state is assumed when system control of the module is stopped.
The following figures show the output type and timeout state.

32-Point Output
Modules
The following list shows the 32-point output modules:
 140DAO85300 (AC Output 230 Vac 4x8 Sink)
 140DDO15310 (DC Output 5 V TTL 4x8 Sink)
 140DDO35300 (DC Output 24 Vdc 4x8 Source)
 140DDO35301 (DC Output 24 Vdc 4x8 Source)
 140DDO35310 (DC Output 24 Vdc True Low 4x8 Sink)
8 7 6 5 4 3 2 1
Group D fault
Group C fault Group B fault
Group A fault
BIN
BCD
Last Value
User Defined
Timeout State:
Output Type:
User Defined Timeout State Points 1-16: 00000000000
I/O Modules
840 USE 100 00 11/2004 561
I/O Map Register
Assignment
The output modules listed above can be configured as either 32 contiguous 0x
references, or as two 4x registers in the following format.
The following figures show the formats for the output modules.
I/O Map Status
Byte
The I/O map status byte (not including 140DAO85300 module) is used by the
modules as follows:
Module Zoom
Selections
Push <Enter> to display and select the output type and the timeout state for the
module. Timeout state is assumed when system control of the module is stopped.
The following figure shows the output type and timeout state.

1234567 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Output
Point 1
Register 2
MSB - First Word
Register 1
MSB - Second Word
Output
Point 17
Groupt A Fault
8 7 6 5 4 3 2 1
Group B Fault
Group C Fault
Group D Fault
Group A Point Fault
Group B Point Fault
Group C Point Fault
Group D Point Fault
140DDO35301 Module only
(overload or short circuit)
Missing field power
or blown fues
BIN
BCD
Last Value
User Defined
Timeout State:
Output Type:
User Defined Timeout State Points 1-16: 0000000000000000
User Defined Timeout State Points 17-32: 0000000000000000
I/O Modules
562 840 USE 100 00 11/2004
96-Point Output
Module
The 96 point output module is:
 140DDO36400 - DC out 24VDC 6x16 Source
I/O Map Register
Assignment
The following figures show the register 1 through 6 format for the 140DDO36400
output module.
I/O Map Status
Byte
The I/O map status byte is used by the module as follows:.
1234567 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Register 1
Output
Point 1
MSB - First Word
Register 2
Output
Point 17
MSB - Second Word
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Register 3
Output
Point 33
MSB - Third Word
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Register 4
Output
Point 49
MSB - Fourth Word
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Register 5
Output
Point 65
MSB - Fifth Word
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
Register 6
Output
Point 81
MSB - Sixth Word
Output 1 to 16 Fault
8 7 6 5 4 3 2 1
Output 17 to 32 Fault
Output 33 to 48 Fault
Output 49 to 64 Fault
Output 65 to 80 Fault
Output 80 to 96 Faul
I/O Modules
840 USE 100 00 11/2004 563
Module Zoom
Selections
 Push <Enter> to display and select the output type and the timeout state for the
module. Timeout state is assumed when system control of the module is stopped.
The following figure shows the output type and timeout state.

BIN
BCD
Last Value
User Defined
Timeout State:
Output Type:
User Defined Timeout State Points 1-16: 0000000000000000
User Defined Timeout State Points 17-32: 0000000000000000
User Defined Timeout State Points 33-48: 0000000000000000
User Defined Timeout State Points 49-64: 0000000000000000
User Defined Timeout State Points 65-80: 0000000000000000
User Defined Timeout State Points 81-96: 0000000000000000
I/O Modules
564 840 USE 100 00 11/2004
140DAO84000 I/O AC Output 24 ... 230 Vac 16x1 Module
Overview The AC Output 24 ... 230 Vac 16x1 module switches 24 ... 230 Vac powered loads.
Specifications The following table shows the specifications for the AC Output 24 ... 230 VAC OUT
module.
Specifications
Number of Output Points 16 isolated
LEDs Active
1 ... 16 (Green) - Indicates point status
Required Addressing 1 word out
Voltage (rms)
Working 20 ... 253 Vac
Absolute Maximum 300 Vac for 10 s
400 Vac for 1 cycle
Frequency 47 ... 63 Hz
ON State Drop / Point 1.5 Vac
Minimum Load Current (rms) 5 mA
Maximum Load Current (rms)
Each Point* 4 A continuous, 20 ... 132 Vac rms
3 A continuous, 170 ... 253 Vac rms
Any Four Contiguous Points 4 A max continuous for the sum of the four points
Per Module* 16 A continuous (See the derating chart)
Off State Leakage / Point (max) 2.5 mA @ 230 Vac
2 mA @ 115 Vac
1 mA @ 48 Vac
1 mA @ 24 Vac
I/O Modules
840 USE 100 00 11/2004 565
The following figure shows the DAO8400
单元当模块的系统控制停止时，假设超时状态。
f