AS-P120-125模块备件

欠
CE系统
顺从
下图显示了符合CE要求的3 A、24 Vdc供电系统。
            

    

屏蔽电缆和
铁氧体磁珠
24伏直流电
常见的
+24伏直流电
地面
护盾
GND
地面
螺钉
背板
PS C
P
U
I/O I/O输入/输出
0        

保持CE与欧洲EMC指令（89/336/EEC）的一致性
以及低压指令（73/23/EEC）、140CPS21100和
140CRA21120和140CRA21220必须按照这些安装
说明书


    


    
    

 !"#
压水堆格兰德。指导
840使用100 00 11/2004 699
详细系统
行政长官
顺从
下图显示了CE合规系统的详细安装
以及明细表标注。
下表提供了CE合规图的零件列表。
量子
背板
接地螺钉
GND
铅
绿色/
+24 VDC黄色
24伏直流电
组件对象模型
棕色
蓝色
地球
地面
绿色/
黄色的
护盾
GND
铅
量子背板
140 XBP XXX 00
量子电源
电源线
如下：
24 Vdc通信（蓝线）
+24 Vdc（棕色导线）
GND
12 56 3 4
标注供应商
（或同等产品）
零件号描述说明
1 Offlex系列
100cy
35005电源线在
电源接地端子
2.Steward 28 BO686-200铁氧体磁珠安装在过滤器和
在两侧用系带固定
铁氧体磁珠的端部。
Fair Rite 264366570
压水堆格兰德。指导
700 840使用100 00 2004年11月
125 Vdc供电
系统
下图显示了符合CE要求的125 Vdc供电系统。
    



屏蔽电缆和
铁氧体磁珠
+125伏直流电
125伏直流电
普通的
地球
地面
护盾
GND
地面
螺钉
屏蔽电缆和铁氧体磁珠
背板
PS C
P
U
输入/输出
或
C
O
M
M
输入/输出
或
C
O
M
M
输入/输出
或
C
O
M
M
输入/输出
或
C
O
M
M
附言
红
0        

保持CE与欧洲EMC指令（89/336/EEC）的一致性
以及低压指令（73/23/EEC）、140CPS51100和
必须按照这些说明安装140CPS52400。


    


    
    

 !"#
压水堆格兰德。指导
840使用100 00 11/2004 701
125 Vdc供电
安装
下图显示了125 Vdc供电系统的详细安装
符合CE要求的零件清单编号。
量子
背板
接地螺钉
GND
铅
绿色/
黄色的
棕色
蓝色
+125伏直流电
125伏直流电
绿色/
黄色的
护盾
GND铅量子电源
按如下方式连接电源：
+125 Vdc（棕色导线）
125 Vdc通信（蓝线）
GND 123 456
地面
普通的
量子背板
140xBpxx0
压水堆格兰德。指导
702 840使用100 00 2004年11月
下表提供了125 Vdc供电安装的零件列表
图形
详图索引供应商（或
等效）
零件号描述说明
1 Offlex系列
100cy
35005电源线在
电源接地端子
2.Steward 28 BO686-200铁氧体磁珠安装在过滤器和
在两侧用系带固定
铁氧体磁珠的端部。
Fair Rite 2643665702
0        

保持CE与欧洲EMC指令（89/336/EEC）的一致性
以及低压指令（73/23/EEC）、140CPS51100和
必须按照这些说明安装140CPS52400。


    


    
    

 !"#$
压水堆格兰德。指导
840使用100 00 11/2004 703
量子电源的系统设计考虑
概述：各种量子模型之间存在一些重要的设计差异
需要系统设计者仔细考虑的电源，以便：
实现大系统性能。主要区别在于
在电源内生成与
电源的运行状况和输入电源的状态。
所有Quantum电源都包括板载早期电源故障检测逻辑，该逻辑：
用于向背板上的所有其他模块发出输入电源故障的信号。这
信号被称为POK（功率OK）并且在高电平（即，
电源正常）。
有一个内部（电源）和一个外部（如
背板和所有其他模块）版本的POK信号。内部POK信号
由所有电源前面板上的Pwr ok LED（发光二极管）表示
供应品。
生成系统POK信号，以便在
系统POK（电源故障）的负向边缘和实际中断
给背板供电。电源故障的早期警告对于
Quantum executive执行有序的系统关闭。
压水堆格兰德。指导
704 840使用100 00 2004年11月
独立的
电源
提供三种型号的独立电源：
下图显示了直接与
量子系统是POK。
•140CPS1100 115…230 Vac输入，3 A输出
•140CPS21100 24 Vdc输入3 A输出owered
Systems for CE
Compliance
The following figure shows the 3 A, 24 Vdc powered systems for CE compliance.
            
    

    

Shielded Cable and
Ferrite Bead
24 Vdc
Common
+24 Vdc
EARTH GROUND
SHIELD
GND
GROUND
SCREWS
BACKPLANE
PS C
P
U
I/O I/O I/O
0        

To maintain CE compliance with the European Directive on EMC (89/336/EEC)
and the Low Voltage Directive (73/23/EEC), the 140CPS21100, the
140CRA21120, and the 140CRA21220 must be installed in accordance with these
instructions.


        

    

    

    

 !"#
Pwr. & Grnding. Guide
840 USE 100 00 11/2004 699
Detailed System
for CE
Compliance
The following figure shows the detailed installation for the CE compliance system
and the parts list callouts.
The following table provides a list of parts for the CE Compliance Figure.
QUANTUM
BACKPLANE
GND SCREWS


GND
LEAD
GREEN/
+24 VDC YELLOW
24 VDC
COM
BROWN
BLUE
EARTH
GROUND
GREEN/
YELLOW
SHIELD
GND
LEAD
QUANTUM BACKPLANE
140 XBP XXX 00
Quantum Power Supply
Wire to the power supply
as follows:
24 Vdc COM (Blue wire)
+24 Vdc (Brown wire)
GND
12 56 3 4
Callout Vendor
(or equivalent)
Part Number Description Instruction
1 Offlex Series
100cy
35005 Line Cord Terminate the shield at the
power supply ground terminal
2 Steward 28 BO686-200 Ferrite Bead Install next to the filter and
secure with tie wraps at Both
ends of the ferrite bead.
Fair Rite 264366570
Pwr. & Grnding. Guide
700 840 USE 100 00 11/2004
125 Vdc Powered
System
The following figure shows the 125 Vdc powered system for CE compliance.
    




SHIELDED CABLE AND
FERRITE BEAD
+125 VDC
125 VDC
COMMON
EARTH
GROUND
SHIELD
GND
GROUND
SCREWS
SHIELDED CABLE AND FERRITE BEAD
BACKPLANE
PS C
P
U
I/O
or
C
O
M
M
I/O
or
C
O
M
M
I/O
or
C
O
M
M
I/O
or
C
O
M
M
PS
RED
0        

To maintain CE compliance with the European Directive on EMC (89/336/EEC)
and the Low Voltage Directive (73/23/EEC), the 140CPS51100 and the
140CPS52400 must be installed in accordance with these instructions.


        

    

    

    

 !"#
Pwr. & Grnding. Guide
840 USE 100 00 11/2004 701
125 Vdc Powered
Installation
The following figure shows the detailed installation for the 125 Vdc powered system
for CE compliance with parts list callouts.
QUANTUM
BACKPLANE
GND SCREWS
GND
LEAD
GREEN/
YELLOW
BROWN


BLUE
+125 VDC
125 VDC
GREEN/
YELLOW
SHIELD
GND LEAD Quantum Power Supply
Wire to the power supply as follows:
+125 Vdc (Brown wire)
125 Vdc COM (Blue wire)
GND 123 456
EARTH GROUND
COMMON
Quantum Backplane
140XBPXXX0
Pwr. & Grnding. Guide
702 840 USE 100 00 11/2004
The following table provides a list of parts for the 125 Vdc Powered Installation
Figure..
Callout Vendor (or
equivalent)
Part Number Description Instruction
1 Offlex Series
100cy
35005 Line Cord Terminate the shield at the
power supply ground terminal
2 Steward 28 BO686-200 Ferrite Bead Install next to the filter and
secure with tie wraps at Both
ends of the ferrite bead.
Fair Rite 2643665702
0        

To maintain CE compliance with the European Directive on EMC (89/336/EEC)
and the Low Voltage Directive (73/23/EEC), the 140CPS51100 and the
140CPS52400 must be installed in accordance with these instructions.


        

    

    

    

 !"#$
Pwr. & Grnding. Guide
840 USE 100 00 11/2004 703
System Design Considerations for Quantum Power Supplies
Overview There exist some important design differences between various models of Quantum
power supplies that require careful consideration by the system designer in order to
achieve maximum system performance. The principal difference lies in the
generation within the power supply of important backplane signals related to the
health of the power supply and the status of the input power.
All Quantum power supplies include on-board early power fail detection logic which
is used to signal all other modules on the backplane that input power has failed. This
signal is called POK (power OK) and is active high (i.e., when the signal is high,
power is OK).
There is both an internal (to the power supply) and an external (as seen by the
backplane and all other modules) version of the POK signal. The internal POK signal
is represented by the Pwr ok LED (light emitting diode) on the front panel of all power
supplies.
The system POK signal is generated so that there is sufficient time between the
negative going edge of system POK (power has failed) and the actual interruption of
power to the backplane. This early warning of power failure is necessary for the
Quantum executive to perform an orderly system shutdown.
Pwr. & Grnding. Guide
704 840 USE 100 00 11/2004
Standalone
Power Supplies
Three models of standalone power supplies are offered:
The following figure shows the single internal POK that relates directly to the
Quantum system POK.
• 140CPS11100 115...230 Vac input 3 A output
• 140CPS21100 24 Vdc input 3 A output
• 140CPS51100 125 Vdc input 3 A output
0
    



Standalone units must be the only power supply installed in a backplane. No fault
tolerant or redundant capability exists in systems powered by standalone power
supplies.
In systems powered by a standalone power supply, the internal power supply POK
is provided directly to the Quantum system POK.


        

    

    

    

 !"#$
Standalone CPS
Internal POK QuantumSystem POK
Pwr. & Grnding. Guide
840 USE 100 00 11/2004 705
Summable
Power Supplies
Four summable power supply models are offered:
A summable power supply may be used as a standalone power supply without
reservation in any Quantum system.
For systems configured with a mix of CPS, NOM, expert, and l/O modules, whose
total current consumption from the backplane exceeds the current provided by one
summable supply, two summable supplies may be used in a single backplane. In
such a system, the total current available on the backplane is the sum of the
capability of both supplies:
 16 A for two 140CPS11410
 16 A for two 140CPS21400
 16 A for two 140CPS41400
 20 A for two 140CPS11420
 16 A for one 140CPS11410 and one 140CPS11420
Use only like summable power supplies (same product reference) except for
140CPS11410 and 140CPS11420, which can be summed.
The summable supplies are designed so that they split the current supplied to the
load almost equally, which also has the added benefit of increasing total system
MTBF, and to distribute the thermal load across the backplane. Summable supplies
should be installed at opposite ends of in the Quantum backplane to maximize the
system thermal performance.
The Quantum system POK signal in systems powered by two summable power
supplies is only true (power is OK) when both internal POK signals (in the
140CPSX14X0) are true. Quantum summable power supplies are not hotswappable.
The following figure shows that the internal summable supply Quantum POKs are
ANDed to create the Quantum System POK.
• 140CPS11410 115...230 Vac input 8 A output
• 140CPS11420 115...230 Vac input 11 A output
• 140CPS21400 24 Vdc input 8 A output
• 140CPS41400 48 Vdc in