AS-BADU-214模块备件

e保护罩必须完全封闭线路过滤器。近似
盖子的尺寸为12.5厘米乘7.5厘米。电线进出口应通过
应变消除套管。
线路滤波器
连接
下图显示了到封闭线路过滤器的接线连接。
防护罩绿色/黄色
（接地，拧上
量子背板）
接地线
金属盒（非
塑料箱需要）
棕褐色
蓝色
案例选项卡
蓝色
压水堆格兰德。指导
714 840使用100 00 2004年11月
840使用100 00 11/2004 715
E
电缆快速布线
一瞥
简介以下信息与CableFast布线系统有关。
这是什么
章
本章包含以下主题：
主题页
CableFast布线系统716的特点
140 CFA 040 00量子电缆快速布线块722
140 CFB 032 00量子电缆快速布线块724
140 CFC 032 00量子电缆快速布线块727
140 CFD 032 00量子电缆快速布线块733
140 CFE 032 00量子电缆快速布线块735
140 CFG 016 00量子电缆快速布线块737
140 CFH 008 00量子电缆快速布线块742
140CFI00800量子电缆快速布线块746
140CFJ00400量子电缆快速布线模块750
140CFK00400量子电缆快速布线块754
CableFast电缆758
CableFast配件763
电缆快速布线
716 840使用100 00 2004年11月
CableFast布线系统的特点
概述：CableFast布线系统由预布线量子场布线终端组成
带，可用于各种电缆长度，端接“D”型
连接器。“D”连接器插入提供的DIN导轨安装接线板
在直通或特殊应用版本中。电缆和接线盒为：
单独订购，所有接线板可用于任何电缆长度。辫子
电缆版本也可用。
量子
模块和
背板
下图显示了量子模块和背板组件。
$    
%确保配线架足够大，以支撑12英尺的电缆。
1A79 1A80
2A82 2A81
快速电缆
电缆快速终端
DIN导轨上的挡块
装电线
潘杜特
装电线
潘杜特
     
CableFastTM
140CFA00400
CableFastTM
140CFA00400
UL文件E123528
UL文件E123528
CableFastTM
140CFA00400
UL文件E123528
CableFastTM
140CFA00400
UL
电缆快速布线
840使用100 00 11/2004 717
规格所有CableFast系统均按照以下规格设计。
规格
额定功率150 Vac/Vdc，每点0.5 A
每点2.0 A时的150 Vac/Vdc*
*需要140CFG01600接线板和
140XTS012XX电缆
介电耐受电压：1060 Vac和1500 Vdc
爬电和间隙符合IEC 1131、UL 508、CSA 22.2#142-1987
接线板导线尺寸
航空站
单线-#12 AWG（2.5 mm2）
两根电线-#16 AWG（1.0 mm2）及以上（见下文
每个端子允许的大导线数。）
注：建议不超过两根导线
曾经使用过。
导线尺寸导线数量
#24 4
#22 4
#18 3
#16 2
#14 1
#12 1
端子螺钉尺寸M3
螺丝刀头尺寸小为0.13“（3.3 mm）平头。
终端螺钉式俘获
端子螺钉表面镀锡板（小197μin.）
终端螺钉拧紧
扭矩
7.2磅-英寸（0.8牛米）
系统可燃性等级94 V-2
温度
工作温度为0…60°C（32…140°F）
储存温度-40…+65°C（-40…+149°F）
湿度0…95%RH不凝结
海拔6666英尺（2000米），完全运行
冲击+/-15 g峰值，11 ms，半正弦波
位移为0.075 mm时10…57 Hz的振动
57…150 Hz@1 g，共10次扫描
安装配置DIN导轨安装，NS35/7.5和NS32
电缆快速布线
718 840使用100 00 11/2004
接线板
选择指南
使用此表选择Quantum I/O模块和CableFast的有效组合
接线板。
140ACI03000 X XX
140ACO02000 X X X
140ACI04000 X
140ACO13000 X
140ARI03010 X
140ATI03000 X（见注3）
140AMM09000 X
140AVI03000 X XX
140AVO02000 X X X
140DAI34000 X X X
140DAI35300 X XXX
140DAI44000 X X
140DAI45300 X XXX
140DAI54000 X X
140DAI54300 X
140DAI55300 X XXX
不允许使用140DAI74000 CableFast
不允许使用140DAI75300 CableFast
140DAM59000 X（见注1）
140DAO84000 X（见注2）
140DAO84010 X（见注2）
140DAO84210 X（见注2）
140DAO84220 X（见注2）
140DAO85300 X（见注1）
140DDI15310 X X
140DDI35300 X XX
140DDI35310 X
140DDI36400与CableFast不兼容。有关推荐电缆140CFA04000、140CFB03200、140CFC03200、140 CFE03200、1400 CFE03200、140 CFG01600，请参见第542页
140CFH00800
140CFI00800
140CFJ00400
140CFK00400
电缆快速布线
840使用100 00 11/2004 719
140DDI67300 X
140DDI84100 X
140DDI85300 X XXX
140DDM3900X
140DDM69000 X（见注1）
140DDO15310 X
140DDO35300 X XX
140DDO35301 X XX
140DDO35310 X
140DDO36400与CableFast不兼容。推荐电缆见第601页。
140DDO84300 X（见注2）
140DDO88500 X（见注1）
140DRA84000 X（见注1）
140DRC83000 X（见注1）
140DSI35300 X
140DVO85300 X
X=有效选择。140CFA04000
140CFB03200
140CFC03200
140CFE03200e protective cover must completely enclose the line filter. Approximate
dimensions for the cover are 12.5 cm by 7.5 cm. Wire entry/exit shall be through
strain relief bushings.
Line Filter
Connections
The following figure shows the wiring connections to the enclosed line filter.
Protective Cover Green/Yellow
(To ground screw on
Quantum backplane)
Ground wire for
metal box (Not
required for plastic box)
Brown Brown
Blue
Case tab
Blue
Pwr. & Grnding. Guide
714 840 USE 100 00 11/2004
840 USE 100 00 11/2004 715
E
CableFast Cabling
At a Glance
Introduction The following information pertains to the CableFast cabling system.
What’s in this
Chapter?
This chapter contains the following topics:
Topic Page
Features of the CableFast Cabling System 716
140 CFA 040 00 Quantum CableFast Cabling Block 722
140 CFB 032 00 Quantum CableFast Cabling Block 724
140 CFC 032 00 Quantum CableFast Cabling Block 727
140 CFD 032 00 Quantum CableFast Cabling Block 733
140 CFE 032 00 Quantum CableFast Cabling Block 735
140 CFG 016 00 Quantum CableFast Cabling Block 737
140 CFH 008 00 Quantum CableFast Cabling Block 742
140CFI00800 Quantum CableFast Cabling Block 746
140CFJ00400 Quantum CableFast Cabling Block 750
140CFK00400 Quantum CableFast Cabling Block 754
CableFast Cables 758
CableFast Accessories 763
CableFast Cabling
716 840 USE 100 00 11/2004
Features of the CableFast Cabling System
Overview The CableFast wiring system consists of pre-wired Quantum field wiring terminal
strips, available in various cable lengths that are terminated with "D" type
connectors. The "D" connectors plug into DIN rail-mounted terminal blocks offered
in straight through or special application versions. Cables and terminal blocks are
ordered separately and all terminal blocks may be used with any cable length. Pigtail
cable versions are also available.
Quantum
Modules and
Backplane
The following figure shows the Quantum modules and backplane components.
$    
%Ensure that the wiring panduits are large enough to support 12 ft. cables.
1A79 1A80
2A82 2A81
CableFast Cables
CableFast Terminal
Blocks on DIN Rails
Wiring
Panduit
Wiring
Panduit
     
    
CableFastTM
140CFA00400
CableFastTM
140CFA00400
UL FILE E123528
UL FILE E123528
CableFastTM
140CFA00400
UL FILE E123528
CableFastTM
140CFA00400
UL 
CableFast Cabling
840 USE 100 00 11/2004 717
Specifications All CableFast systems are designed to the following specifications.
Specifications
Power Ratings 150 Vac/Vdc @ 0.5 A per point
150 Vac/Vdc @ 2.0 A per point *
*Requires the 140CFG01600 Terminal Block and the
140XTS012XX Cable
Dielectric Withstanding Voltage 1060 Vac and 1500 Vdc
Creepage and Clearance per IEC 1131, UL 508, CSA 22.2 #142-1987
Terminal Block Wire Sizes per
Terminal
One wire - #12 AWG (2.5 mm2)
Two wires - #16 AWG (1.0 mm2) and above (See below
for the maximum number of wires allowed per terminal.)
Note: It is recommended that no more than two wires be
used at one time.
Wire Size Number of Wires
#24 4
#22 4
#18 3
#16 2
#14 1
#12 1
Terminal Screw Size M3
Screwdriver Head Size 0.13" (3.3 mm) flat head min.
Terminal Screw Type Captive
Terminal Screw Finish Tin plate (197 μin min.)
Terminal Screw Tightening
Torque
7.2 lb.-in (0.8 Nm)
System Flammability Rating 94 V-2
Temperature
Operating 0 ... 60° C (32 ... 140° F)
Storage -40 ... +65° C (-40 ... +149° F)
Humidity 0 ... 95% RH noncondensing
Altitude 6,666 ft. (2000 m) full operation
Shock +/- 15 g peak, 11 ms, half sine wave
Vibration 10 ... 57 Hz @ 0.075 mm displacement
57 ... 150 Hz @ 1 g, total 10 sweeps
Mounting Configuration DIN rail mount, NS35/7.5 and NS32
CableFast Cabling
718 840 USE 100 00 11/2004
Terminal Block
Selection Guide
Use this table to select valid combinations of Quantum I/O modules and CableFast
terminal blocks.
140ACI03000 X XX
140ACO02000 X X X
140ACI04000 X
140ACO13000 X
140ARI03010 X
140ATI03000 X (See Note 3)
140AMM09000 X
140AVI03000 X XX
140AVO02000 X X
140DAI34000 X X
140DAI35300 X XXX
140DAI44000 X X
140DAI45300 X XXX
140DAI54000 X X
140DAI54300 X
140DAI55300 X XXX
140DAI74000 CableFast Not Allowed
140DAI75300 CableFast Not Allowed
140DAM59000 X (See Note 1)
140DAO84000 X (See Note 2)
140DAO84010 X (See Note 2)
140DAO84210 X (See Note 2)
140DAO84220 X (See Note 2)
140DAO85300 X (See Note 1)
140DDI15310 X X
140DDI35300 X XX
140DDI35310 X
140DDI36400 Not compatible with CableFast. See p. 542 for recommended cables 140CFA04000 140CFB03200 140CFC03200 140CFE03200 140CFE03200 140CFG01600
140CFH00800
140CFI00800
140CFJ00400
140CFK00400
CableFast Cabling
840 USE 100 00 11/2004 719
140DDI67300 X
140DDI84100 X
140DDI85300 X XXX
140DDM39000 X
140DDM69000 X (See Note 1)
140DDO15310 X
140DDO35300 X XX
140DDO35301 X XX
140DDO35310 X
140DDO36400 Not compaitble with CableFast. See p. 601 for recommended cables.
140DDO84300 X (See Note 2)
140DDO88500 X (See Note 1)
140DRA84000 X (See Note 1)
140DRC83000 X (See Note 1)
140DSI35300 X
140DVO85300 X
X = Valid Selections. 140CFA04000
140CFB03200
140CFC03200
140CFE03200
140CFE03200
140CFG01600
140CFH00800
140CFI00800
140CFJ00400
140CFK00400
These are the maximum load current capacities of the 140CFA04000 and
CFG01600 terminal blocks:
 When using the 140CFA04000 terminal block, the indicated module outputs are
limited to 0.5 A per point, 150 Vac maximum and 0.5 A per point, 150 Vdc maximum.
     When using the 140CFG01600 terminal block and either the 140XTS012xx or
140XTS102XX high power cables, the indicated module output ratings are 2 A per
point, 150 Vac maximum, and 2 A per point, 150 Vdc maximum.

 The 140CFA04000 block does not incorporate an isometric barrier and is not
recommended for use with the 140ATI03000 TC module. Without such a barrier,
temperature readings may vary up to 2 degrees from one end of the block to the
other. If the application can tolerate this temperature error, the block (and module
remote CJC) may be used
CableFast Cabling
720 840 USE 100 00 11/2004
CableFast
Terminal Blocks
This table includes