V4550220-EN模块备件

有关预设Alpha代码的更多详细信息，请参阅相关装置文档。
有关Alpha代码锁配置的更多详细信息，请参见77页的图24。
机械钥匙是预设的，不得更改。这防止了
可拆卸接口放置在错误类型的基板上。
CI869 AF 100接口D C
CI872 MOD5接口D E
CI871 PROFINET IO接口D（1）B（1）
CI873以太网/IP设备网
界面
D（1）B（1）
BC810 CEX总线
互连单元
答
SM810 C B
SM811 D D
S800输入/输出单元各不相同–参见S800 I/O
产品/用户指南
各种–见S800 I/O
产品/用户指南
（1） 关键位置对于CI867、CI868、CI871和CI873是共同的。因此，必须谨慎
在现场替换中执行。确保插入了正确的CI，尤其是热插入。
确保基板和待安装装置具有兼容的Alpha代码。
否则可能导致设备损坏。在上安装单元时遇到任何困难
特定的基板指示阿尔法码锁定的差异。
不要操纵锁定装置。ABB将不承担以下责任：
由操作锁定装置引起的错误。
表4.工厂预设的Alpha代码（续）
单元键位置1键位置2
2节预制铝型材的安装
3BSE036351-510 A 77
图24.装置底板-阿尔法码锁布置
预设
字母代码键
在单个配置中安装PM86x/TP830处理器单元2节安装
78 3BSE036351-510 A
在单个中安装PM86x/TP830处理器单元
配置
使用以下步骤沿DIN导轨安装处理器单元：
1.如果已经安装，则从
处理器单元的侧面。
2.安装处理器单元、通信接口和S800 I/O
单位。
所有PM8xx的通信接口位于左侧的CEX总线上
处理器单元。PM8xx的S800输入/输出单元位于电气上
处理器单元右侧的模块总线。
3.轻轻地将它们压在一起，确保ModuleBus和CEXBus通过基板连接器正确连接。
4.将总线终端重新插入远的通信单元
来自处理器单元。
a、 对于CEX总线TB850（如果使用电缆TK850，则为TB851），请参见
80页和81页的图26。使用BC810时，请参见
82页。如果CEX总线上未使用任何单元，则无总线终端
必修的。
b、 有关ModuleBus TB807，请参阅S800 I/O文档。如果没有单位
在模块总线上使用，不需要总线终端。
本主题不适用于PM891处理器单元。请参阅中的安装PM891
87页的单一配置。
对于PM861/PM864/PM865/PM866，插入RCU链路终端插头
TB852，位于RCU链路连接器处。必须始终使用终端插头
对于PM861/PM864/PM865/PM866，当在单个配置中运行时。
当冗余处理器在单个配置中运行时，使用RCU
链路电缆TK851，如果RCU链路终端插头TB852不可用。
2节安装：在单个配置中安装PM86x/TP830处理器单元
3BSE036351-510 A 79
5.底板电缆连接：
a、 连接电源线和电源监控信号（如适用）
从SS82x到螺钉端子SA和SB（参见83页图28）。
b、 将控制网络电缆连接到CN1（单连接）或CN1+
CN2（冗余连接）。
c、 将串行协议连接到COM3。
d、 使用电缆TK212将控制生成器连接到COM4（如果需要
改变IP地址等）。否则，将控件生成器连接到
控制网络。
6.将光学模块总线连接到处理器单元上的光学触点
（参见32页图2和131页图40）。关于
S800 I/O中提供了光缆选择和电缆长度
文档
7.PM8xx配有内部备用电池。当电池要充电时
使用时，将其放置在内部电池支架中（参见193页的图63）。
当要使用外部SB821/SB822电池单元时，请按照
请参阅页的“安装SB821外部电池单元”中的说明
143/安装144页的SB822可充电外部电池单元。
请注意，光学模块总线的连接与处理器的连接相同
用于S800 I/O中的FCI（参见160页的图54）
不要将内部备用电池放在电池座中，直到
AC 800M控制器已正常通电，内存备份
功能已激活，即B（蓄电池）LED闪烁。如果没有正常
将电源连接到处理器单元，电池已就位，然后
CPU内存将立即开始消耗电池p!For further details on pre-set Alpha codes, refer to the relevant unit documentation.
See Figure 24 on page 77 for further details of the Alpha code lock arrangement.
The mechanical keys are delivered pre-set and must not be altered. This prevents the
removable interface being placed on the wrong type of baseplate.
CI869 AF 100 Interface D C
CI872 MOD5 Interface D E
CI871 PROFINET IO Interface D(1) B(1)
CI873 EtherNet/IP DeviceNet
Interface
D(1) B(1)
BC810 CEX-Bus
Interconnection Unit
C A
SM810 C B
SM811 D D
S800 I/O Units Various – see S800 I/O
Product/User’s Guide
Various – see S800 I/O
Product/User’s Guide
(1) The key positions are common to CI867, CI868, CI871 and CI873. Hence caution must be
exercised in field replacement. Ensure that correct CI is inserted, especially in hot insert.
Ensure that the baseplate and the unit to be mounted have compatible Alpha codes.
Otherwise it may result in equipment damage. Any difficulty in installing a unit on a
particular baseplate indicates a difference in Alpha Code lock.
Do not manipulate the locking device. ABB will take no responsibility for
errors caused by manipulating locking devices.
Table 4. Factory Pre-set Alpha Codes (Continued)
Unit Key Position 1 Key Position 2
Section 2 Installation Prefabricated aluminum profile
3BSE036351-510 A 77
Figure 24. Unit Baseplate – Alpha Code Lock Arrangement
Pre-Set
Alpha Code Keys
Installing the PM86x/TP830 Processor Unit in Single Configuration Section 2 Installation
78 3BSE036351-510 A
Installing the PM86x/TP830 Processor Unit in Single
Configuration
Use the procedure below to install the processor unit along the DIN-rail:
1. If already mounted, remove the CEX-Bus and ModuleBus terminations from
the sides of the processor unit.
2. Mount the processor unit, the communication interfaces, and the S800 I/O
units.
The communication interfaces for all PM8xx is on the CEX-Bus to the left of
the processor unit. The S800 I/O units for PM8xx is on the electrical
ModuleBus to the right of the processor unit.
3. Press them gently together and make sure that the ModuleBus and the CEXBus are correctly connected, via baseplate connectors.
4. Reinsert the bus terminations into the communication units at farthest away
from the processor unit.
a. For CEX-Bus TB850 (TB851 if cable TK850 is used), see Figure 25 on
page 80 and Figure 26 on page 81. When using BC810, see Figure 27 on
page 82. If no units are used on the CEX-Bus, no bus termination is
required.
b. For ModuleBus TB807, refer to the S800 I/O documentation. If no units
are used on the ModuleBus, no bus termination is required.
This topic does not apply to the PM891 processor unit. See Installing PM891 in
Single Configuration on page 87.
For PM861/PM864/PM865/PM866 insert the RCU Link Termination plug
TB852, at the RCU Link connector. The termination plug must always be used
for PM861/PM864/PM865/PM866 when running in single configuration.
When a redundant processor is running in a single configuration use the RCU
Link Cable TK851, if the RCU Link Termination plug TB852 is not available.
Section 2 Installation Installing the PM86x/TP830 Processor Unit in Single Configuration
3BSE036351-510 A 79
5. Baseplate cable connections:
a. Connect the power leads and, if applicable, power supervision signals
from SS82x to screw terminals SA and SB (see Figure 28 on page 83).
b. Connect the Control Network cables to CN1 (single connection) or CN1 +
CN2 (redundant connection).
c. Connect the serial protocol to COM3.
d. Connect the Control Builder to COM4 with cable TK212 (if required for
changing an IP address etc). Otherwise connect the Control Builder to the
Control Network.
6. Connect the optical ModuleBus to the optical contacts on the processor unit
(see Figure 2 on page 32 and Figure 40 on page 131). Information regarding
optical cable selection and cable length is provided in the S800 I/O
documentation.
7. The PM8xx is supplied with an internal back-up battery. When the battery is to
be used, place it in the Internal Battery Holder (see Figure 63 on page 193).
When the external SB821/SB822 battery unit is to be used, install it according
to the instructions in Installing the SB821 External Battery Unit on page
143/Installing the SB822 Rechargeable External Battery Unit on page 144.
Note that connection to the optical ModuleBus is identical to that for the processor
unit and for the FCI in S800 I/O (see Figure 54 on page 160.)
Do not place the internal back-up battery in the battery holder until the
AC 800M Controller has been powered-up normally and the memory back-up
function has been activated, that is, the B(attery) LED flashes. If no normal
power supply is connected to the processor unit with the battery in place, then
the CPU memory will immediately start to consume battery p