AS-BDAP-292模块备件

SB822可充电外部电池单元
使用以下步骤连接可充电外部电池单元：
1.交付时，锂离子电池组内部未连接。遵循
包装箱中随附的数据和安装表中的步骤：
正确连接电池组。
2.将SB822可充电外部电池单元安装在
喧闹的轨道。
3.将24V电源连接到包装箱内的连接器。
4.将24V电源连接到电池单元（X3）
5.确保AC 800M控制器已通电，且电池已接通
PM8xx的前端正在闪烁
6.连接SB822可充电外部电池单元，使用2米（2.2码）
电缆TK821V020。将一端插入电池单元，另一端插入
PM8xx处理器单元的外部电池电源插座（参见上的图2
32页）。
7.确保SB822上的绿色电源指示灯和黄色充电指示灯
被打开。
8.在冗余CPU配置中，包含两个
PM861/PM864/PM865/PM891处理器单元，也使用两个SB822电池
每个处理器单元一个。
9.由于电池并联连接，在使用
外部电池，从PM8xx上卸下内部电池，以便：
避免减少可用内存和备份时间。
在AC 800M控制器安装完成之前，不要连接TK821V020电缆
正常通电且存储器备份功能已激活，
B（蓄电池）LED闪烁。如果PM8xx未连接正常电源
处理器单元，CPU内存将立即开始消耗电池电量
连接电缆时
2节安装I/O装置的安装
3BSE036351-510 A 145
I/O单元的安装
有关安装、拆卸和释放程序的更多信息
输入/输出装置，请参阅相应的输入/输出系统文档。
机柜内安装
下图是AC 800M控制器如何供电的示例
电源单元、表决单元和S800 I/O单元可配置并安装在
橱柜：
•146页图49：壁柜-单电源布置
•147页图50：壁柜-双电源（本地/现场）
安排
•148页图51：落地式机柜-单元布置
（冗余PSU）
DIN导轨采用支撑铝型材，以确保刚性。
参见403页的图118。
图中所示机柜为ABB制造的机柜：
•RE820：壁柜
•RM550：落地柜
机柜安装2节安装
146 3BSE036351-510 A
图49.壁柜-单电源布置
24 V配电
终端
电源断路器SD831
单元
缆绳
管
铝
轮廓
缆绳
膨胀
模块总线
2节安装机柜中的安装
3BSE036351-510 A 147
图50壁柜-双电源（本地/现场）布置
电源断路器
单元
SD831
24 V配电
（单位）
（机柜中的单元）
SD831
（现场）
24 V配电
（现场设备）
机柜安装2节安装
148 3BSE036351-510 A
图51.落地式机柜（水平单元布置）
投票
单位
SS832断路器
干线
SD832冗余
电源装置
冗余的
权力
供应单位
（现场
设备）
SD832
2节适当通风的安装尺寸
3BSE036351-510 A 149
适当通风的安装尺寸
为了保持通过AC 800M控制器单元的足够冷却气流，有
装置上方50 mm（2英寸）和下方25 mm（1英寸）范围内不得有障碍物，
如149页的图52所示。注意CPU和通信
接口必须安装在水平DIN导轨上。
图52.通风要求-小安装尺寸
>261毫米
（10.3英寸）
>50毫米（2.0英寸）
>50毫米（2.0英寸）
>25毫米（1.0英寸）
>25毫米（1.0英寸）
无障碍区域
无障碍区域
适当通风的安装尺寸2节安装
150 3BSE036351-510 A
3BSE036351-510 A 151
3节配置
一般资料
使用工程工具Control Builder，可以配置硬件（I/O
以及通信单元），并用控制语言制作应用程序
根据IEC 61131-3。程序可以离线编译和运行，以帮助
后将应用程序下载到控制器之前的过程仿真。这个
控件生成器提供了一组选项，每个选项都有自己的属性集。仅仅
选择接近系统要求的选项。
•控制生成器文档–用于配置信息
•控制软件文档——用于可用功能。
控件生成器联机帮助提供了以下详细的分步信息：
为AC 800M控制器创建应用程序。SB822 Rechargeable External Battery Unit
Use the following procedure to connect the rechargeable external battery unit:
1. At delivery the Li-Ion battery package is not connected internally. Follow the
steps in the Data and installation sheet, which is enclosed in the packing box, to
connect the battery package properly.
2. Mount the SB822 rechargeable external battery unit at a suitable position on
the DIN-rail.
3. Connect the 24V supply to the connector enclosed in the packing box.
4. Connect the 24V supply to the battery unit (X3)
5. Make sure that the AC 800M controller is powered and that the battery LED in
the front of PM8xx is flashing
6. Connect the SB822 rechargeable external battery unit, use the 2 m (2.2 yd)
cable TK821V020. Plug one end into the battery unit and the other into the
external battery supply socket of the PM8xx processor unit (see Figure 2 on
page 32).
7. Make sure that the green Power LED and the yellow Charge LED on SB822
are turned on.
8. In redundant CPU configuration containing two
PM861/PM864/PM865/PM891processor units, use also two SB822 battery
units, one for each processor unit.
9. Due to the batteries being connected in parallel, it is necessary, when using the
external battery, to remove the internal battery from the PM8xx in order to
avoid reducing available memory back-up time.
Do not connect the TK821V020 cable until the AC 800M Controller has been
powered-up normally and the memory back-up function has been activated, that is,
the B(attery) LED flashes. If no normal power supply is connected to the PM8xx
processor unit, the CPU memory will immediately start to consume battery power
when the cable is connected
Section 2 Installation Installation of I/O Units
3BSE036351-510 A 145
Installation of I/O Units
For further information regarding mounting, removing and releasing procedures for
I/O Units, refer to the appropriate I/O system documentation.
Installation in Cabinets
The figures listed below are examples of how the AC 800M Controllers, Power
Supply units, Voting units and S800 I/O units can be configured and mounted within
cabinets:
• Figure 49 on page 146: Wall Cabinet – Single Power Supply Arrangement
• Figure 50 on page 147: Wall Cabinet – Dual Power Supply (Local/Field)
Arrangement
• Figure 51 on page 148: Floor Mounted Cabinet – Unit Arrangement
(Redundant PSU)
The DIN-rails are using the supporting Al-profile to ensure rigidness.
See Figure 118 on page 403.
The cabinets shown in the figures are ABB manufactured cabinets:
• RE820: Wall Cabinet
• RM550: Floor Cabinet
Installation in Cabinets Section 2 Installation
146 3BSE036351-510 A
Figure 49. Wall Cabinet – Single Power Supply Arrangement
24 V Distribution
Terminals
Mains Breaker SD831
Unit
Cable
Duct
Aluminum
Profile
Cable
Expansion
ModuleBus
Section 2 Installation Installation in Cabinets
3BSE036351-510 A 147
Figure 50. Wall Cabinet – Dual Power Supply (Local/Field) Arrangement
Mains Breaker
Unit
SD831
24 V Distribution
(Units)
(Units in Cabinet)
SD831
(Field)
24 V Distribution
(Field Equipment)
Installation in Cabinets Section 2 Installation
148 3BSE036351-510 A
Figure 51. Floor Mounted Cabinet (Horizontal Unit Arrangement)
Voting
Units
SS832 Breakers
Mains
SD832 Redundant
Power Supply Units
Redundant
Power
Supply Units
(Field
Equipment)
SD832
Section 2 Installation Mounting Dimensions for Proper Ventilation
3BSE036351-510 A 149
Mounting Dimensions for Proper Ventilation
To maintain adequate cooling airflow through the AC 800M Controller units, there
must be no obstruction within 50 mm (2 in) above and 25 mm (1 in) below the units,
as shown in Figure 52 on page 149. Note that the CPU and Communication
Interfaces must be mounted on a horizontal DIN-rail.
Figure 52. Ventilation Requirements – Minimum Mounting Dimensions
>261 mm
(10.3 in)
>50 mm (2.0 in)
>50 mm (2.0 in)
>25 mm (1.0 in)
>25 mm (1.0 in)
Unobstructed areas
Unobstructed areas
Mounting Dimensions for Proper Ventilation Section 2 Installation
150 3BSE036351-510 A
3BSE036351-510 A 151
Section 3 Configuration
General Information
Using the engineering tool Control Builder, it is possible to configure hardware (I/O
and communication units) and make application programs with control languages
according to IEC 61131-3. Programs can be compiled and run off-line as an aid to
process simulation before finally downloading an application to the controller. The
Control Builder offers a set of options, each with its own set of properties. Simply
select the option that is closest to system requirements.
• Control Builder documentation – for configuration information
• Control Software documentation – for available functionality.
Control Builder Online Help provides detailed step-by-step information when
creating an application for the AC 800M Controller.