AS-BDEA-202模块备件

RIO/Genius远程I/O
TRIO是Genius远程I/O产品，提供离散、模拟和高速
用于连接AC 800M的计数器块。I/O块单元的配置
并且使用控制构建器M完成CI862。
驱动系统3节配置
168 3BSE036351-510 A
驱动系统
ABB标准（Std）和工程（Eng）驱动器可连接至AC 800M
通过以下任何方式：
•光学模块总线
•CI801和PROFIBUS DP
•NPBA-12、RPBA-01或FPBA-01 PROFIBUS DP适配器模块
使用CI854
•RETA-02或FENA-01/-11以太网适配器模块以及CI871
（PROFINET IO）
•CI858驱动总线接口。
模块总线
在单CPU配置中，ABB驱动器可以通过以下方式连接到处理器单元：
光学模块总线。参见171页的图59。ABB驱动器的数量
可连接到光模块总线的光模块总线可由
下式：
（ABB驱动器数量）<84-（12个（TB820s数量））
也就是说，每个驱动器使用一个ModuleBus集群。
PROFIBUS DP和CI801
在单CPU和冗余CPU配置中，ABB驱动器可以通过
PROFIBUS DP和CI801。参见171页的图59。只有标准驱动器可以
连接到CI801。每个驱动器可连接十四（14）个标准驱动器
如果未连接I/O单元，则为CI801。对于可以使用的驱动器数量：
当I/O单元（TB820）和标准驱动器均为
已连接，请参阅有关PROFIBUS DP的FCI的文档。
有关ABB驱动器及其类型（Std和Eng）的更多信息，请参阅
S800 I/O文档。
有关分支装置（171页图59）的信息，请参阅ABB驱动器
系统文档。
ABB驱动器也可以通过PROFIBUS DP（CI854/CI854A）与直接
连接到PROFIBUS DP从模块NPBA-12、RPBA-01和FPBA-01。
3节传动系统的配置
3BSE036351-510 A 169
PROFINET IO和CI871
RETA-02以太网适配器模块和FENA-01/-11以太网适配器
模块是ABB驱动器的可选设备，可连接
驱动器连接到PROFINET IO（PNIO）网络。驱动器被视为PNIO设备
在PROFINET IO网络上，它与所有PNIO控制器兼容
支持PROFINET IO和子插槽的工作站。
驱动总线接口CI858
ABB驱动器可通过CI858装置连接至AC 800M，参见
171页和172页的图60。驱动器接口可用于控制
多24个驱动器或逆变器单元。
驱动连接的主要通信功能包括：
•数据集通信
•广播系统时间
•监控和诊断功能
AC 800M和CI858之间的数据交换由八个数据集组成。
驱动器连接多可以传输8个数据集/1毫秒。
多个驱动器的连接需要使用分支单元，这使得
具有物理星形拓扑的逻辑总线的构造，请参见页的图60
172.分支单元可以是链式的。
驱动器连接支持以下驱动器：
•ACS 600单驱动
•ACS 600多驱动器
•ACS 600晶闸管供电装置
•ACS 600 IGBT电源装置
•ACS 800产品系列
•ACS 140-AC S400
•DCS 600和DCS 400
•ACS 6000产品系列/大型驱动器RIO/Genius Remote I/O
TRIO is a Genius remote I/O product that provides discrete, analog and high-speed
counter blocks for connection to the AC 800M. Configuration of the I/O block units
and the CI862 is done using Control Builder M.
Drive System Section 3 Configuration
168 3BSE036351-510 A
Drive System
ABB Standard (Std) and Engineered (Eng) Drives can be connected to AC 800M
through any of the following:
• The optical ModuleBus
• CI801 and PROFIBUS DP
• NPBA-12, RPBA-01, or FPBA-01 PROFIBUS DP Adaptor modules along
with CI854
• RETA-02 or FENA-01/-11 Ethernet Adapter modules along with CI871
(PROFINET IO)
• CI858 DriveBus Interface.
ModuleBus
In single CPU configuration, ABB Drives can be connected to the processor unit via
the optical ModuleBus. See Figure 59 on page 171. The number of ABB Drives
which can be connected to the optical ModuleBus, can be described by the
following equation:
(No. of ABB Drives) < 84 - (12 x (No. of TB820s))
that is, each Drive uses one ModuleBus cluster.
PROFIBUS DP and CI801
In single and redundant CPU configuration, ABB Drives can be connected via
PROFIBUS DP and CI801. See Figure 59 on page 171. Only Standard Drives can
be connected to CI801. Fourteen (14) Standard Drives can be connected to each
CI801 if there are no I/O units connected. For the number of Drives that can be
connected to the same CI801, when both I/O units (TB820) and Standard Drives are
connected, refer to documentation about FCI for PROFIBUS DP.
For more information about ABB Drives and its types (Std and Eng) refer to
S800 I/O documentation.
For information about Branching Unit (Figure 59 on page 171) see ABB Drive
System documentation.
ABB drives can also be connected via PROFIBUS DP (CI854/CI854A), with direct
connection to PROFIBUS DP slave modules NPBA-12, RPBA-01, and FPBA-01.
Section 3 Configuration Drive System
3BSE036351-510 A 169
PROFINET IO and CI871
The RETA-02 Ethernet Adapter module and FENA-01/-11 Ethernet Adapter
module are optional devices for ABB drives, which enables the connection of the
drive to a PROFINET IO (PNIO) network. The drive is considered as a PNIO device
on the PROFINET IO network, and it is compatible with all PNIO controller
stations that support PROFINET IO and sub-slots.
DriveBus Interface CI858
ABB drives can be connected to the AC 800M via the CI858 unit, see Figure 59 on
page 171 and Figure 60 on page 172. The drive interface can be used for controlling
up to 24 drives or inverter units.
Main communication functions of the drive connection are:
• Dataset communication
• Broadcast system time
• Supervision and diagnostics functions
The data exchange between the AC 800M and the CI858 consists of eight datasets.
The drive connection is able to transfer at the maximum 8 datasets / 1 ms.
Connection of multiple drives requires the use of a branching unit, which enables
the construction of a logical bus with physical star topology, see Figure 60 on page
172. The branching units can be chained.
The following drives are supported by the drive connection:
• ACS 600 single drive
• ACS 600 multi drive
• ACS 600 thyristor supply units
• ACS 600 IGBT supply units
• ACS 800 product family
• ACS 140-AC S400
• DCS 600 and DCS 400
• ACS 6000 product family/large drives