AS-BDEP-214模块备件

CI860基金会现场总线高速以太网单元
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI862三路I/O接口单元
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI865 SAT I/O接口单元
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI867 Modbus TCP接口单元
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI868
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI869
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI871
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
表23.AC 800M控制器-验证系统运行是否令人满意
LED指示灯状态
AC 800M
控制器
地位
冗余CPU4节操作验证
188 3BSE036351-510 A
冗余CPU的验证
在冗余配置中，检查以下LED指示灯是否亮起
PM861/PM864/PM865/PM866/PM891和SM810/SM811（如使用）
（见188页表24）。
CI872
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
CI873
F（故障）红色LED必须熄灭，OK
R（un）绿色LED必须点亮（稳定）OK
表24.AC 800M控制器
（PM861/PM864/PM865/PM866/PM891/SM810/SM811）-验证
冗余配置中的系统运行令人满意
LED指示灯状态AC 800M控制器
主CPU和备用CPU的状态
基本（ary）黄色ON基本（ARI）黄色OFF OK
双黄亮双黄亮OK
主SM810/SM811备用SM810/SM811
基本（ary）黄色ON基本（ARI）黄色OFF OK
同步黄色ON同步黄色ON OK
表23.AC 800M控制器-验证系统运行是否令人满意
LED指示灯状态
AC 800M
控制器
地位
四节冗余CPU的运行验证
3BSE036351-510 A 189
手动切换由以下步骤启动：
•重置主CPU
•关闭主CPU电源
检查两个CPU上的黄色双LED是否随后点亮，以及
原备用CPU上的PRIM LED亮起，现在用作主CPU。
其他单位见185页表23。
要检查冗余是否正常工作，请执行手动切换
从主CPU到备用CPU。这应该谨慎地进行，
以及考虑对该过程可能产生的影响。
决不能将RCU链路电缆从主处理器单元上拆下
在冗余操作期间。拔下电缆可能会导致装置停止CI860 FOUNDATION Fieldbus High Speed Ethernet Unit
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI862 TRIO I/O Interface Unit
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI865 Satt I/O Interface Unit
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI867 Modbus TCP Interface Unit
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI868
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI869
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI871
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
Table 23. AC 800M Controller – Verification of Satisfactory System Operation
LED Indicator Status
AC 800M
Controller
Status
Verification of Redundant CPU Section 4 Operation
188 3BSE036351-510 A
Verification of Redundant CPU
Check, in redundant configuration, the following LED indicators on
PM861/PM864/PM865/PM866/PM891 and, if used, SM810/SM811
(see Table 24 on page 188).
CI872
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
CI873
F(ault) Red LED must be OFF OK
R(un) Green LED must be ON (steady) OK
Table 24. AC 800M Controller
(PM861/PM864/PM865/PM866/PM891/SM810/SM811) – Verification of
Satisfactory System Operation in Redundant configuration
LED Indicator Status AC 800M Controller
Status Primary CPU Back-up CPU
PRIM(ary) yellow ON PRIM(ary) yellow OFF OK
DUAL yellow ON DUAL yellow ON OK
Primary SM810/SM811 Back-up SM810/SM811
PRIM(ary) yellow ON PRIM(ary) yellow OFF OK
SYNC yellow ON SYNC yellow ON OK
Table 23. AC 800M Controller – Verification of Satisfactory System Operation
LED Indicator Status
AC 800M
Controller
Status
Section 4 Operation Verification of Redundant CPU
3BSE036351-510 A 189
A manual switch-over is initiated by:
• Resetting the Primary CPU
• Powering off the Primary CPU
Check that the yellow DUAL LED subsequently lights up on both CPUs, and that
the PRIM LED lights up on the former Backup CPU now acting as Primary CPU.
For other units see Table 23 on page 185.
To check that the redundancy, is working correctly, perform a manual switch-over
from the Primary CPU to the Backup CPU. This should be performed with caution,
and consideration to possible impact on the process.
The RCU Link Cable must NEVER be removed from the primary Processor Unit
during redundant operation. Removal of the cable may cause the unit to stop