AS-FLSH-004C模块备件

主要特征
•使用RJ45实现的两个RS-232C端口
位于TP853基板上的连接器（用作
机载RS-232C端口的扩展
如果需要更多RS-232C端口，则为PM8xx）。
•调制解调器支持
•简单的DIN导轨安装
•传输速度可在75波特和
19200波特。
•多种协议的现成软件选项
•预设、两个字母的Alpha码锁定装置
参见75页的表4，安装在机组底座中，
防止安装不兼容的组件。
描述
提供具有完全调制解调器支持的RS-232C信道
对于COM1和COM2端口中的每一个。调制解调器（用于
示例：TC562），如果电缆延伸，则需要
超过15米。
附录A硬件单元CI853和TP853–RS-232C接口
3BSE036351-510 A 293
功能框图
图71.方框图——CI853
DC/DC总线接口
微处理器
FPROM、SRAM，
+5伏
+24伏
通信分机
通信扩展基板
通信线路
表达
扩展总线
表达
扩展总线
双端口RWM和
两个串行接口
转换器
CI853和TP853–RS-232C接口附录A硬件单元
294 3BSE036351-510 A
指标
技术数据
表80.CI853 RS-232C–LED指示
指示/颜色功能
在装置中检测到F（故障）/红色错误。由
控制软件。由设置并清除
控制器复位期间的硬件。
R（un）/绿色运行。由控制软件控制。
在重置期间由硬件清除
控制器。
如果传输到COM1端口，Tx1/黄色闪烁。
如果从COM1端口接收，Rx1/黄色闪烁。
如果从COM2端口传输，Tx2/黄色闪烁。
如果从COM2端口接收，Rx2/黄色闪烁。
表81.CI853–RS-232C通信接口规范
项目描述
带调制解调器的双非隔离RS-232C端口
信号。
通道数：2个通道
协议由软件、应用程序和许可证确定。
适用于Modbus、西门子3964R、COMLI
以及定制设计的协议。请参阅
CB了解详细信息。
通信速度可在75到19200波特之间选择。
75, 110, 134.5, 150, 300, 600, 1200, 1800, 2000,
2400、9600和19200波特。
适用特定于协议的限制。
附录A硬件单元CI853和TP853–RS-232C接口
3BSE036351-510 A 295
未隔离的电流隔离
状态指示灯正常运行：绿色。异常故障：红色。
四个流量指示器-接收和发送-由控制
交通速度：闪烁黄色。
接头TP853上的两个RJ45接头。
电流消耗
（来自CEX总线24 V直流）
典型100 mA（大150 mA）
典型功耗2.4 W
根据EN60529和IEC 529，防护等级为IP20。
重量700克（1.5磅）（装有CI853和
TP853）
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
有关更多信息，请参见安装尺寸
用于149页的适当通风。
表81.CI853–RS-232C通信接口规范（续）
项目描述
CI854/CI854A和TP854–PROFIBUS DP接口附录A硬件单元
296 3BSE036351-510 A
CI854/CI854A和TP854–PROFIBUS DP接口
主要特征
•带冗余线路接口的PROFIBUS DP（两个
位于TP854上的DB9母接头
基板）。
•简单的DIN导轨安装。
•除了循环数据传输外
CI854/CI854A支持非循环DP
通信和从冗余。
•通过使用中继器，可以连接
多124个节点与一个PROFIBUS DP（32
在一个段上允许节点）。
•预设、两个字母的Alpha码锁定装置
安装在装置底座中，防止安装
不兼容的组件。
•传输速度可在9.6 kbit/s之间选择
和12Mbit/s。
•支持PROFIBUS DP主冗余
（CI854A）。
•支持热插拔（CI854A）。
描述
CI854/CI854A/TP854将PROFIBUS DP连接到AC 800M。PRODFIBUS DP
可以直接连接远程I/O S800和S900等从设备。
PROFIBUS PA从设备可通过PROFIBUS链接设备连接
LD 800P。
底板TP854有两个用于连接的内螺纹DB9连接器
支持线路冗余的PROFIBUS DP。底板具有密码锁，请参阅
75页的表4，防止将不正确类型的装置安装到
TP854基板。
（1） 仅限CI854A
(1)
(1)
附录A硬件单元CI854/CI854A和TP854–PROFIBUS DP接口
3BSE036351-510 A 297
CI854/CI854A扩展单元包含CEX总线逻辑、CPU内核
带存储器、带线路冗余单元和DC/DC的PROFIBUS接口
通过CEXBus从+24V电源提供适当电压的转换器。
PROFIBUS DP必须始终在两个外部节点处终止。这是
通常通过使用带有内置终端的连接器来完成。保证正确
工作终端连接器必须插入并供电。
必须满足屏蔽/接地的PROFIBUS DP要求。这个
PROFIBUS DP安装指南要求cablKey Features
• Two RS-232C ports implemented with RJ45
connectors, located on the TP853 Baseplate, (act as
an extension of the onboard RS-232C port on
PM8xx should more RS-232C ports be required).
• Modem support
• Simple DIN-rail mounting
• Transmission speed selectable between 75 baud and
19200 baud.
• Ready-made Software options for several protocols
• Pre-set, two-letter Alpha code locking device
see Table 4 on page 75, installed in unit base,
prevents mounting of incompatible components.
Description
Provides an RS-232C channel with full modem support
for each of the COM1 and COM2 ports. A modem (for
example TC562) will be required if the cables extend
beyond 15 m.
Appendix A Hardware Units CI853 and TP853 – RS-232C Interface
3BSE036351-510 A 293
Functional Block Diagram
Figure 71. Block Diagram – CI853
DC/DC Bus interface
Microprocessor with
FPROM, SRAM,
+5 V
+24 V
Communication Extension Unit
Communication Extension Base plate
Communication lines
Communication
Extension Bus
Communication
Extension Bus
Dual Port RWM and
two serial interfaces
converter
CI853 and TP853 – RS-232C Interface Appendix A Hardware Units
294 3BSE036351-510 A
Indicators
Technical Data
Table 80. CI853 RS-232C – LED Indications
Indication/ Color Function
F(ault) /Red Error detected in the unit. Controlled by the
Control Software. Set and cleared by the
Hardware during Reset of the controller.
R(un) /Green Operating. Controlled by the Control Software.
Cleared by the Hardware during Reset of the
controller.
Tx1 /Yellow Flashes if transmission to the COM1 port.
Rx1 /Yellow Flashes if receiving from the COM1 port.
Tx2 /Yellow Flashes if transmission from the COM2 port.
Rx2 /Yellow Flashes if receiving from the COM2 port.
Table 81. CI853 – RS-232C Communication Interface Specifications
Item Description
Type Double unisolated RS-232C ports with modem
signals.
Number of channels 2 channels
Protocol Determined by software, application and licenses.
Intended for Modbus, Siemens 3964R, COMLI
and custom designed protocols. Please refer to
CB for details.
Communication speed Selectable in steps from 75 to 19200 baud.
75, 110, 134.5, 150, 300, 600, 1200, 1800, 2000,
2400, 9600, 19200 baud.
Protocol specific restrictions apply.
Appendix A Hardware Units CI853 and TP853 – RS-232C Interface
3BSE036351-510 A 295
Galvanic isolation Unisolated
Status indicators Running normally: Green. Exceptional fault: Red.
Four traffic indictors - Rx and Tx - controlled by
traffic pace: Flashing yellow.
Connector Two RJ45 connectors on TP853.
Current consumption
(from CEX-Bus 24 V DC)
100 mA typical (150 mA max.)
Power Dissipation 2.4 W typical
Protection Rating IP20 according to EN60529, IEC 529.
Weight 700 g (1.5 lb) (package CI853K01with CI853 and
TP853)
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
For further information see Mounting Dimensions
for Proper Ventilation on page 149.
Table 81. CI853 – RS-232C Communication Interface Specifications (Continued)
Item Description
CI854/CI854A and TP854 – PROFIBUS DP Interface Appendix A Hardware Units
296 3BSE036351-510 A
CI854/CI854A and TP854 – PROFIBUS DP Interface
Key Features
• PROFIBUS DP with redundant line interface (two
DB9 female connector located on the TP854
Baseplate).
• Simple DIN-rail mounting.
• In addition to the cyclic data transfer the
CI854/CI854A supports acyclic DP
communication and slave redundancy.
• By using repeaters it is possible to connect a
maximum of 124 nodes to one PROFIBUS DP (32
nodes are permitted on one segment).
• Pre-set, two-letter Alpha code locking device
installed in unit base prevents mounting of
incompatible components.
• Transmission speed selectable between 9.6 kbit/s
and 12 Mbit/s.
• Support of PROFIBUS DP master redundancy
(CI854A).
• Supports hot swap (CI854A).
Description
The CI854/CI854A/TP854 connects PROFIBUS DP to AC 800M. PRODFIBUS DP
slave devices like the remote I/Os S800 and S900 can be connected directly.
PROFIBUS PA slave devices can be connected via the PROFIBUS linking device
LD 800P.
The Baseplate TP854 has two female DB9 connectors for connecting
PROFIBUS DP with support of line redundancy. The baseplate has a code lock, see
Table 4 on page 75, that prevents the installation of an incorrect type of unit onto
the TP854 Baseplate.
(1) CI854A only
(1)
(1)
Appendix A Hardware Units CI854/CI854A and TP854 – PROFIBUS DP Interface
3BSE036351-510 A 297
The CI854/CI854A expansion unit contains the CEX-Bus logic, the CPU-kernel
with memory, the PROFIBUS interface with line redundancy unit and a DC/DC
converter that supplies the appropriate voltages from the +24V supply, via the CEXBus.
The PROFIBUS DP must always be terminated at the two outer nodes. This is
usually done by using connectors with built-in termination. To guarantee a correct
working termination the connector has to be plugged and power supplied.
The PROFIBUS DP requirements for screening/earthing have to be fulfilled. The
PROFIBUS DP installation guideline requires that the cable shield should be
connected to ground at both ends of the cable. This has to be done although the
CI854/CI854A already connects the shield to ground via the connectors