141MMS53502模块备件

CI856和TP856–S100 I/O接口
主要特征
•提供一个S100 I/O端口（36针中心线
位于TP856上的微型带状连接器
基板）。
•简单的DIN导轨安装
•CI856处理I/O扫描和更新
S100 I/O单元位于多五个I/O机架中。这个
小循环扫描/更新间隔为0.2ms，
尽管这将取决于I/O类型和
I/O点。
•预设、两个字母的Alpha码锁定装置
安装在装置底座中，防止安装
不兼容的组件。
•支持热插拔。
描述
CI856/TP856将S100 I/O连接到AC 800M
TP856基板有一个36针中心线微型
用于连接S100 I/O机架的带状连接器。这个
底板有一个密码锁，见第75页的表4
防止将不正确类型的装置安装到
TP856基板。
CI856扩展单元包含CEX总线逻辑、S100 I/O总线逻辑、CPU
以及从+24V电源提供适当电压的DC/DC转换器，
通过CEX总线。
CI856和TP856–S100 I/O接口附录A硬件单元
306 3BSE036351-510 A
功能框图
图74.方框图——CI856
CEX总线接口
+5 V S100输入/输出总线接口
+24伏
通信分机
通信扩展基板
S100通信电缆
表达
扩展总线
表达
扩展总线
DC/DC
转换器
+3.3伏
+2.5伏
冷火µP
MCF5307
SDRAM
8MB
闪光
2 MB
附录A硬件单元CI856和TP856–S100 I/O接口
3BSE036351-510 A 307
指标
技术数据
表86.CI856–S100输入/输出LED指示灯
名称/颜色功能
检测到F（故障）/红色单元错误。由CI856软件控制。
在控制器复位期间由硬件设置。
成功后由CI856软件清除
启动。
R（un）/绿色运行。由控制软件控制。
在控制器复位期间由硬件清除。
在S100 I/O访问超时时，TO/黄色闪烁。
表87.CI856 S100 I/O接口规范
项目价值
S100型I/O通信接口
电流隔离No
状态指示灯正常运行为绿色，异常故障为红色，
在S100，指示灯为黄色闪烁
I/O访问超时。
连接器36针中心线微型色带
连接器，母
电流消耗
（来自CEX总线24 V直流）
典型120 mA（大200 mA）
典型功耗2.9 W
容量：多5个I/O机架，每个机架具有20个I/O单元
根据EN60529和IEC 529，防护等级为IP20
CI856和TP856–S100 I/O接口附录A硬件单元
308 3BSE036351-510 A
重量700克（1.5磅）（包装CI856K01，带
CI856和TP856）
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
表87.CI856 S100 I/O接口规范（续）
项目价值
附录A硬件单元CI857和TP853–INSUM接口
3BSE036351-510 A 309
CI857和TP853–INSUM接口
主要特征
•提供一个以太网端口（RJ45连接器
位于TP853基板上）。只有COM1是
用于INSUM。
•简单的DIN导轨安装
•通过以下方式与INSUM通信：
以太网/LON网关
•预设、两个字母的Alpha码锁定装置
安装在装置底座中，防止安装
不兼容的组件。
•支持热插拔。
描述
CI857/TP853可用于连接AC 800M
控制器通过以太网上的TCP/IP连接到INSUM，以及
具有LON接口的INSUM TCP/IP网关
与底层INSUM系统通信。
TP853底板有两个RJ45以太网
连接器，但仅使用COM1连接器
用于连接到INSUM。
底板有一个代码锁，见第75页的表4，
防止安装不正确类型的装置
安装在TP853基板上。
CI857扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，通过+24 V电源提供适当的电压
CEX巴士。以太网电缆必须通过
以太网交换机。CI856 and TP856 – S100 I/O Interface
Key Features
• Provides one S100 I/O port, (a 36 pin centerline
miniature ribbon connector located on the TP856
Baseplate).
• Simple DIN-rail mounting
• The CI856 handles I/O scanning and updating of
S100 I/O units located in up to five I/O racks. The
minimum cyclic scan/update interval is 0.2ms,
though this will depend on I/O type and number of
I/O points.
• Pre-set, two-letter Alpha code locking device
installed in unit base prevents mounting of
incompatible components.
• Supports Hot swap.
Description
The CI856/TP856 connects S100 I/O to AC 800M.The
TP856 Baseplate has one 36-pin centerline miniature
ribbon connector for connecting S100 I/O racks. The
baseplate has a code lock, see Table 4 on page 75, that
prevents installation of an incorrect type of unit onto the
TP856 Baseplate.
The CI856 expansion unit contains the CEX-Bus logic, S100 I/O-bus logics, CPU
and a DC/DC converter that supplies appropriate voltages from the +24 V supply,
via the CEX-Bus.
CI856 and TP856 – S100 I/O Interface Appendix A Hardware Units
306 3BSE036351-510 A
Functional Block Diagram
Figure 74. Block Diagram – CI856
CEX-Bus interface
+5 V S100 I/O-bus interface
+24 V
Communication Extension Unit
Communication Extension Baseplate
S100 communication cable
Communication
Extension Bus
Communication
Extension Bus
DC/DC
converter
+3.3 V
+2.5 V
ColdFire µP
MCF5307
SDRAM
8 MB
Flash
2 MB
Appendix A Hardware Units CI856 and TP856 – S100 I/O Interface
3BSE036351-510 A 307
Indicators
Technical Data
Table 86. CI856 – S100 I/O LED Indicators
Designation/Color Function
F(ault) /Red Unit error detected. Controlled by CI856 Software.
Set by the Hardware during controller Reset.
Cleared by the CI856 Software after successful
startup.
R(un) /Green Operating. Controlled by the Control Software.
Cleared by the Hardware during controller Reset.
TO /Yellow Flashes at S100 I/O access time-outs.
Table 87. CI856 S100 I/O Interface Specifications
Item Value
Type S100 I/O Communication Interface
Galvanic isolation No
Status indicators Run normally green, FAIL exceptionally red,
the indicator TO are yellow flashing at S100
I/O access time-outs.
Connector 36 pin centerline miniature ribbon
connector, female
Current consumption
(from CEX-Bus 24 V DC)
120 mA typical (200 mA max.)
Power dissipation 2.9 W typical
Capacity Max 5 I/O racks with 20 I/O units each
Protection Rating IP20 according to EN60529, IEC 529
CI856 and TP856 – S100 I/O Interface Appendix A Hardware Units
308 3BSE036351-510 A
Weight 700 g (1.5 lb) (package CI856K01 with
CI856 and TP856)
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
Table 87. CI856 S100 I/O Interface Specifications (Continued)
Item Value
Appendix A Hardware Units CI857 and TP853 – INSUM Interface
3BSE036351-510 A 309
CI857 and TP853 – INSUM Interface
Key Features
• Provides one Ethernet port, (RJ45 connector
located on the TP853 Baseplate). Only COM1 is
used for INSUM.
• Simple DIN-rail mounting
• Provides communication with INSUM via
Ethernet/LON Gateway
• Pre-set, two-letter Alpha code locking device
installed in unit base prevents mounting of
incompatible components.
• Supports Hot swap.
Description
The CI857/TP853 can be used to connect an AC 800M
controller to INSUM through TCP/IP over Ethernet and
an INSUM TCP/IP Gateway that has a LON interface
communicating with the underlying INSUM system.
The TP853 Baseplate has two RJ45 Ethernet
connectors, though only the COM1connector is used
for connecting to INSUM.
The baseplate has a code lock, see Table 4 on page 75,
that prevents the installation of an incorrect type of unit
onto the TP853 Baseplate.
The CI857 expansion unit contains the CEX-Bus logic, a communication unit and a
DC/DC converter that supplies appropriate voltages from the +24 V supply via the
CEX-Bus. The Ethernet cable must be connected to the main network through an
Ethernet Switch.