490NAA27102模块备件

表88.CI857–INSUM接口LED指示灯
名称/颜色功能
检测到F（故障）/红色单元错误。受控
软件在以下过程中由硬件设置和清除：
控制器复位。
R（un）/绿色运行。由控制软件控制。
在控制器复位期间由硬件清除。
Tx1/黄色：闪烁黄色LED，指示从
通信单元COM1端口。
Rx1/黄色闪烁：接收数据时，黄色LED闪烁
从COM1端口。
Tx2关闭未使用。
Rx2关闭未使用。
表89.CI857 INSUM接口规范
项目价值
以太网单元的类型。
INSUM协议与TCP/IP
通信速度10 Mbit/s（半双工）
状态指示灯正常运行：绿色。异常故障：
红色。两个交通指示器-Tx1/Rx1-
由交通速度控制：闪烁黄色。
连接器2 RJ45（仅使用COM1）。
CI857和TP853–INSUM接口附录A硬件单元
312 3BSE036351-510 A
电流消耗
（来自CEX总线24 V直流）
典型150 mA（大200 mA）。
典型功耗为3.6W。
根据EN60529和IEC 529，防护等级为IP20。
重量700克（1.5磅）（包装CI857K01，带
CI857和TP853）。
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
表89.CI857 INSUM接口规范（续）
项目价值
附录A硬件单元CI858和TP858–驱动总线接口
3BSE036351-510 A 313
CI858和TP858–驱动总线接口
主要特征
•为DriveBus提供三个光学连接器，
I/O总线和PC工具。
•简单的DIN导轨安装。
•预设、两个字母的Alpha码锁定装置
安装在装置底座中，防止安装
不兼容的组件。
描述
CI858单元包括一个通信扩展
基板、通信扩展单元。全部的
电子设备和所有功能位于
通信扩展单元板。
CI858有三个连接器。驱动总线连接器
有关ABB驱动器的连接，请参见
168页特殊I/O连接，请参见
158页用于下载固件的工具连接
与ABB驱动工具的通信单元
DriveDebug或DriveWindow。
底板有一个代码锁，见75页的表4，
防止安装不正确类型的装置
到基板上。
CI858扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，通过+24 V电源提供适当的电压
CEX巴士。
为了使用工具连接，PC必须配备
PCMCIA/DDCS（笔记本电脑）或ISA/DDCS接口。
CI858和TP858–驱动总线接口附录A硬件单元
314 3BSE036351-510 A
功能框图
图76.方框图——CI858
附录A硬件单元CI858和TP858–驱动总线接口
3BSE036351-510 A 315
指标
技术数据
表90.CI858–驱动总线接口LED指示灯
名称/颜色功能
检测到F（故障）/红色单元错误。
R（un）/绿色运行。
Dbus；Rx/黄色接收LED指示接收数据帧
在汽车上。
Dbus；Tx/黄色传输LED，指示数据传输
驱动总线上的框架。
输入/输出；Rx/黄色接收LED指示接收数据帧
在I/O总线上。
输入/输出；Tx/黄色传输LED，指示数据传输
I/O总线上的帧。
工具/黄色接收LED指示接收数据帧
在PC工具总线（1）上。
（1） 该LED在装置前部不可见。可以通过中的通风孔看到
塑料外壳。
工具/黄色传输LED，指示数据传输
PC工具总线上的框架（1）。
表91.CI858–驱动总线规范
项目价值
通信速度4 Mbit/s
连接器三个光学连接器
CI858和TP858–驱动总线接口附录A硬件单元
316 3BSE036351-510 A
电流消耗
（来自CEX总线24 V直流）
大200 mA。
外部电源电压：小17 V
25 V典型值
大30 V
根据EN60529和IEC 529，防护等级为IP20。
批准：CE标记并符合要求
EMC指令EMCD中规定
2004/108/EC，根据标准
EN 50081-2和EN 61000-6-2。Table 88. CI857 – INSUM Interface LED Indicators Designation/Color Function F(ault) /Red Unit error detected. Controlled by Control Software. Set and cleared by the Hardware during controller Reset. R(un) /Green Operating. Controlled by the Control Software. Cleared by the Hardware during controller Reset. Tx1 /Yellow flashing A yellow LED indicating transmission from the communication unit COM1 port. Rx1 /Yellow flashing A yellow LED flashes when data is being received from the COM1 port. Tx2 OFF Not used. Rx2 OFF Not used. Table 89. CI857 INSUM Interface Specifications Item Value Type Ethernet unit. Protocol INSUM TCP/IP Communication speed 10 Mbit/s (half duplex) Status indicators Running normally: Green. Exceptional fault: Red. Two traffic indictors - Tx1/Rx1 - controlled by traffic pace: Flashing yellow. Connector 2 RJ45 (only COM1 is used). CI857 and TP853 – INSUM Interface Appendix A Hardware Units 312 3BSE036351-510 A Current consumption (from CEX-Bus 24 V DC) 150 mA typical (200 mA max.). Power dissipation 3.6 W typical. Protection Rating IP20 according to EN60529, IEC 529. Weight 700 g (1.5 lb) (package CI857K01with CI857 and TP853). Dimensions W 59 x H 185 x D 127.5 mm (W 2.9 x H 7.3 x D 5.0 in) Table 89. CI857 INSUM Interface Specifications (Continued) Item Value Appendix A Hardware Units CI858 and TP858 – DriveBus Interface 3BSE036351-510 A 313 CI858 and TP858 – DriveBus Interface Key Features • Provides three optical connectors for DriveBus, I/O bus and PC tools. • Simple DIN-rail mounting. • Pre-set, two-letter Alpha code locking device installed in unit base prevents mounting of incompatible components. Description The CI858 unit consists of a communication expansion base plate, a communication expansion unit. All electronic devices and all functions are located on the communication expansion unit board. The CI858 has three connectors. DriveBus connector for connection of ABB Drives, see Drive System on page 168. Special I/O connection, see I/O Systems on page 158. A tool connection for downloading firmware to the communication unit with the ABB Drives tools DriveDebug or DriveWindow. The baseplate has a code lock, see Table 4 on page 75, that prevents the installation of an incorrect type of unit onto the Baseplate. The CI858 expansion unit contains the CEX-Bus logic, a communication unit and a DC/DC converter that supplies appropriate voltages from the +24 V supply via the CEX-Bus. In order to use the tool connection, the PC must be equipped with a PCMCIA/DDCS (laptop) or an ISA/DDCS (desktop) interface. CI858 and TP858 – DriveBus Interface Appendix A Hardware Units 314 3BSE036351-510 A Functional Block Diagram Figure 76. Block Diagram – CI858 Appendix A Hardware Units CI858 and TP858 – DriveBus Interface 3BSE036351-510 A 315 Indicators Technical Data Table 90. CI858 – DriveBus Interface LED Indicators Designation/Color Function F(ault) /Red Unit error detected. R(un) /Green Operating. Dbus; Rx /Yellow RECIEVE LED indicating reception of data frames on the DriveBus. Dbus; Tx /Yellow TRANSMIT LED indicating transmission of data frames on the DriveBus. I/O; Rx /Yellow RECIEVE LED indicating reception of data frames on the I/O bus. I/O; Tx /Yellow TRANSMIT LED indicating transmission of data frames on the I/O Bus. Tools /Yellow RECIEVE LED indicating reception of data frames on the PC Tool bus(1). (1) This LED is not visible in the front of the unit. It can be seen through the ventilation holes in the plastic housing. Tools /Yellow TRANSMIT LED indicating transmission of data frames on the PC Tool Bus(1). Table 91. CI858 – DriveBus Specifications Item Value Communication speed 4 Mbit/s Connectors Three optical connectors CI858 and TP858 – DriveBus Interface Appendix A Hardware Units 316 3BSE036351-510 A Current consumption (from CEX-Bus 24 V DC) 200 mA max. External supply voltage 17 V minimum 25 V typical 30 V max Protection Rating IP20 according to EN60529, IEC 529. Approval CE-marked and meets the requirements specified in EMC Directive EMCD 2004/108/EC according to the standards EN 50081-2 and EN 61000-6-2.