490NAA27106模块备件

技术数据
表93.CI860–基金会现场总线高速以太网规范
项目价值
以太网单元的类型。
基金会现场总线高速协议
以太网、TCP/IP。
通信速度：IEEE中定义的10 Mbit/s/100 Mbit/s
802.3 100baseTX。
状态指示灯正常运行：绿色。
异常故障：红色。
一个交通指示器-RxTx-由控制
交通速度。
连接器RJ45
电流消耗
（来自CEX总线24 V直流）
典型值为100 mA（大值为150 mA）。
典型功耗为2.4W。
根据EN60529和IEC 529，防护等级为IP20。
重量700克（1.5磅）（包装CI860K01，带
CI860和TP860）。
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
附录A硬件单元CI862和TP862-TRIO/Genius接口
3BSE036351-510 A 321
CI862和TP862-TRIO/Genius接口
主要特征
•用于与AC 800M通信的CEX总线接口
•R（un）、F（ault）、通信错误、主（总线）的LED指示灯
主）和双（冗余）
•运行于32 MHz的摩托罗拉MCF5307微控制器
•用于代码的2 MB闪存
•用于配置和动态数据的8 MB SDRAM，也用作双端口
CI862和AC 800M之间的存储器
•从CEX总线+24V电源和DC/DC转换器到+5V的电源，
+3.3V和+2.5V
•用于读取本地I/O块的手持式监视器端口
•现场总线终端开关
描述
CI862（图78）将三重现场总线连接到控制器AC 800M。这个
CI862和AC 800M之间的连接通过CEX总线完成。
单个CI862可以将30个块连接到单个三重LAN。AC 800M可以有
多四个单三路局域网。TRIO的大I/O为1000个I/O点。
CI862可用于以下冗余处理器模块配置：
以下条件：
a、 如果CI862与冗余PM866一起使用，则仅TK850 CEX总线
延长电缆应用于PM866模块之间的互连。
不得使用BC810。
b、 如果CI862与其他冗余处理器模块一起使用
（PM861A/PM864A/PM865），BC810或TK850 CEX总线延长电缆
可用于两个处理器模块之间的互连。
PM891处理器模块不支持CI862。
CI862和TP862-TRIO/Genius接口附录A硬件单元
322 3BSE036351-510 A
图78.CI862 TRIO/Genius接口。
图79中的三个块是独立的、可配置的I/O块，用于
将现场设备连接到CI862通信总线。这些块可以是
单独安装在机器上、接线盒中或分组在机架或面板中。
三重块由铸铝制成，重量约为1.8千克
（4磅）。它的尺寸约为22.5 x 10 x 7.5厘米（9 x 4 x 3英寸）。每个
block拥有自己的通信能力和微处理器，并提供
用于连接输入和输出设备的6至32个电路。你可以放置积木
以任何组合或顺序在总线上。您可以在同一块上混合使用块
公共汽车各种类型的块可用，如中所列chnical Data
Table 93. CI860 – FOUNDATION Fieldbus High Speed Ethernet Specifications
Item Value
Type Ethernet unit.
Protocol FOUNDATION Fieldbus High Speed
Ethernet, TCP/IP.
Communication speed 10 Mbit/s / 100 Mbit/s defined in IEEE
802.3 100baseTX.
Status indicators Running normally: Green.
Exceptional fault: Red.
One traffic indictor - RxTx - controlled by
traffic pace.
Connector RJ45
Current consumption
(from CEX-Bus 24 V DC)
100 mA typical (150 mA max.).
Power dissipation 2.4 W typical.
Protection Rating IP20 according to EN60529, IEC 529.
Weight 700 g (1.5 lb) (package CI860K01with
CI860 and TP860).
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
Appendix A Hardware Units CI862 and TP862 - TRIO/Genius Interface
3BSE036351-510 A 321
CI862 and TP862 - TRIO/Genius Interface
Key Features
• CEX-Bus interface for communication to AC 800M
• LED indicators for R(un), F(ault), Communication Error, Primary (Bus
Master), and Dual (redundancy)
• Motorola MCF5307 Microcontroller running at 32 MHz
• 2 MByte Flash memory for code
• 8 MByte SDRAM for configuration and dynamic data, also used as Dual Port
Memory between CI862 and AC 800M
• Power supply from the CEX bus +24V supply with DC/DC converters to +5V,
+3.3V, and +2.5V
• Hand Held Monitor Port used for reading Local I/O Block
• Field bus termination switch
Description
CI862, Figure 78, connects a TRIO Field Bus to the controller AC 800M. The
connection between CI862 and AC 800M is done via the CEX-Bus.
A single CI862 can connect 30 blocks to a single TRIO LAN. AC 800M can have
up to four single TRIO LANs. The maximum I/O with TRIO is 1000 I/O points.
The CI862 can be used in a redundant processor module configuration under the
following conditions:
a. If the CI862 is used with redundant PM866, only the TK850 CEX-bus
extension cable shall be used for interconnection between the PM866 modules.
The BC810 shall not be used.
b. If the CI862 is used with other redundant processor modules
(PM861A/PM864A/PM865), either BC810 or TK850 CEX-bus extension cable
can be used for interconnection between the two processor modules.
The CI862 is not supported with the PM891 processor module.
CI862 and TP862 - TRIO/Genius Interface Appendix A Hardware Units
322 3BSE036351-510 A
Figure 78. CI862 TRIO/Genius interface.
TRIO blocks, Figure 79, are self-contained, configurable I/O blocks used to
interface field devices to the CI862 communications bus. These blocks can be
individually installed on machines, in junction boxes, or grouped in racks or panels.
A TRIO block is made of cast aluminum, and weighs approximately 1.8 kgs
(4 pounds). It measures approximately 22.5 x 10 x 7.5 cm (9 x 4 x 3 inches). Each
block has its own communications capability and microprocessor, and provides
from 6 to 32 circuits for connecting input and output devices. You can place blocks
on the bus in any combination or sequence. You can use a mix of blocks on the same
bus. Various types of blocks are available as listed in