490NAD91103模块备件

名称/颜色功能
R（un）和F（ault）
LED灯亮起
CI865装置正在制造过程中
配置。留出时间完成这项工作。
如果条件持续存在，且没有其他单元指示灯点亮
CEX总线点亮：
•检查PM8xx内的CEX总线保险丝
处理器单元
•从PM8xx启动复位信号（INIT）
处理器单元
•更换CI865装置
CI865装置上的F（故障）指示灯亮起，正在进行
重新启动。留出时间完成这项工作。
如果情况依然存在，请更换单元。
COM A/COM B LED关闭、断电或复位模式
COM A/COM B LED亮起
绿色
频道OK
COM A/COM B LED为
闪绿
临时错误或需要初始设置
COM A/COM B LED亮起
红色
模块损坏，必须更换
COM A/COM B LED为
闪红
坏信道电缆
COM A/COM B LED是铁路
红色
道路配置不适合网络
COM A/COM B LED为
闪烁的红色/绿色
网络存在数据流问题
COM A/COM B LED是铁路
红/绿
自检
附录A硬件单元CI865和TP865–Satt I/O接口
3BSE036351-510 A 331
技术数据
表97.Satt I/O CI865接口规范
项目价值
类型Satt I/O通信接口
电流隔离是
状态指示灯正常运行为绿色，异常故障为红色，
COM A/COM B
连接器BNC
电流消耗
（来自CEX总线24 V直流）
典型120 mA（大200 mA）
典型功耗2.9 W
容量敢达3968个二进制I/O通道
根据EN60529和IEC 529，防护等级为IP20
重量700克（1.5磅）（包装CI865xxx，带
CI865和TP865）
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
CI867和TP867–Modbus TCP接口附录A硬件单元
332 3BSE036351-510 A
CI867和TP867–Modbus TCP接口
主要特征
•提供一个10/100Mbps快速以太网端口，
（RJ45连接器位于TP867基板上）。
•提供一个10Mbps以太网端口（RJ45
位于TP867基板上的连接器）。
•简单的DIN导轨安装。
•提供与Modbus TCP的通信
通过以太网的协议。
•预设、两个字母的Alpha码锁定装置
安装在装置底座中，防止安装
不兼容的组件。
•支持热插拔。
描述
CI867/TP867可用于连接
AC 800M控制器到外部以太网设备
使用Modbus TCP协议。
TP867基板有两个RJ45以太网
连接器，其中CH1连接器可以使用10Mbps
或者100Mbps（兆比特/秒），而CH2仅使用10Mbps。
底板有一个密码锁（见第75页表4）
这可防止将不正确类型的装置安装到TP867基板上。
CI867扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，通过+24 V电源提供适当的电压
CEX巴士。以太网电缆必须通过
以太网交换机。
附录A硬件单元CI867和TP867–Modbus TCP接口
3BSE036351-510 A 333
功能框图
图82.方框图——CI867
CI867和TP867–Modbus TCP接口附录A硬件单元
334 3BSE036351-510 A
指标
技术数据
表98.Modbus TCP接口CI867-LED指示灯
名称/颜色功能
检测到F（故障）/红色单元错误。由硬件在
控制器复位。之后由控制软件控制
重置。
R（un）/绿色运行。控制器期间由硬件清除
重置。复位后由控制软件控制。
RxTx1/闪烁时为黄色。以太网包在以下位置发送/接收：
通道1。
RxTx2/闪烁时为黄色。以太网包在以下位置发送/接收：
CH 2。
基本（ary）此LED在单冗余配置中点亮。
指示冗余配置中的主CI867。
双：当CI867以冗余方式运行时，此LED点亮
配置
表99.Modbus TCP接口CI867-技术规范
项目价值
类型以太网单元
Modbus-TCP协议
IEEE 802.3u 10/100BaseTx中定义的通信速度CH1 10 Mbit/s/100 Mbit/s
IEEE 802.3 10Base-T中定义的通信速度CH2 10 Mbit/sDesignation/Color Function
Neither R(un) nor F(ault)
LED’s are ON
The CI865 unit is in the process of being
configured. Allow time for this to finalize.
If the condition persists, and no other unit LED on
the CEX-Bus is lit:
• Check the CEX-Bus fuse inside the PM8xx
processor unit
• Initiate a reset signal (INIT) from the PM8xx
processor unit
• Replace the CI865 unit
F(ault) LED is ON The CI865 unit is in the process of being
restarted. Allow time for this to finalize.
Replace unit if the condition persists.
COM A/COM B LED is OFF Power OFF or Reset Mode
COM A/COM B LED is solid
green
Channel OK
COM A/COM B LED is
flashing green
Temporary error or need initial setup
COM A/COM B LED is solid
red
Module is broken, has to be replaced
COM A/COM B LED is
flashing red
Bad channel cable
COM A/COM B LED is railroad
red
The road is not configured right for the network
COM A/COM B LED is
flashing red/green
Network has data flow problem
COM A/COM B LED is railroad
red/green
Self test
Appendix A Hardware Units CI865 and TP865 – Satt I/O Interface
3BSE036351-510 A 331
Technical Data
Table 97. Satt I/O CI865 Interface Specifications
Item Value
Type Satt I/O Communication Interface
Galvanic isolation Yes
Status indicators Run normally green, FAIL exceptionally red,
COM A/COM B
Connector BNC
Current consumption
(from CEX-Bus 24 V DC)
120 mA typical (200 mA max.)
Power dissipation 2.9 W typical
Capacity Up to 3968 binary I/O channels
Protection Rating IP20 according to EN60529, IEC 529
Weight 700 g (1.5 lb) (package CI865xxx with
CI865 and TP865)
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
CI867 and TP867 – Modbus TCP Interface Appendix A Hardware Units
332 3BSE036351-510 A
CI867 and TP867 – Modbus TCP Interface
Key Features
• Provides one 10/100Mbps Fast Ethernet port,
(RJ45 connector located on the TP867 Baseplate).
• Provides one 10Mbps Ethernet port, (RJ45
connector located on the TP867 Baseplate).
• Simple DIN-rail mounting.
• Provides communication with Modbus TCP
protocol via Ethernet.
• Pre-set, two-letter Alpha code locking device
installed in unit base prevents mounting
of incompatible components.
• Supports hot swap.
Description
The CI867/TP867 can be used to connect an
AC 800M controller to external Ethernet devices
using Modbus TCP protocol.
The TP867 Baseplate has two RJ45 Ethernet
connectors, where CH1 connector can use 10Mbps
or 100Mbps (Mega bits/sec.) and CH2 use10Mbps only.
The baseplate has a code lock (see Table 4 on page 75)
that prevents the installation of an incorrect type of unit onto the TP867 Baseplate.
The CI867 expansion unit contains the CEX-Bus logic, a communication unit and a
DC/DC converter that supplies appropriate voltages from the +24 V supply via the
CEX-Bus. The Ethernet cable must be connected to the main network through an
Ethernet Switch. 
Appendix A Hardware Units CI867 and TP867 – Modbus TCP Interface
3BSE036351-510 A 333
Functional Block Diagram
Figure 82. Block Diagram – CI867
CI867 and TP867 – Modbus TCP Interface Appendix A Hardware Units
334 3BSE036351-510 A
Indicators
Technical Data
Table 98. Modbus TCP Interface CI867 - LED indicators
Designation/Color Function
F(ault) / Red Unit error detected. Set by the Hardware during
Controller Reset. Controlled by Control Software after
Reset.
R(un) / Green Operating. Cleared by the Hardware during Controller
Reset. Controlled by Control Software after Reset.
RxTx1 / Yellow When flashing. Ethernet packages are sent/received at
CH 1.
RxTx2 / Yellow When flashing. Ethernet packages are sent/received At
CH 2.
PRIM(ary) This LED is on in single and redundant configuration.
Indicates Primary CI867 in redundant configuration.
DUAL This LED is on when CI867 is running in redundant
configuration.
Table 99. Modbus TCP Interface CI867 - Technical Specification
Item Value
Type Ethernet unit
Protocol Modbus TCP
Communication speed CH1 10 Mbit/s / 100 Mbit/s defined in IEEE 802.3u 10/100BaseTx
Communication speed CH2 10 Mbit/s defined in IEEE 802.3 10Base-T