490NAD91104模块备件

状态指示灯正常运行：绿色。
异常故障：红色。
两个交通指示器——RxTx1和RxTx2——由控制
交通速度：闪烁黄色
交通指示器CH2–RxTx2–由控制
交通速度。
运行为主：黄色。
在冗余配置中运行：黄色。
连接器RJ45
电流消耗（来自CEXBus 24VDC）
典型160 mA（大250 mA）
典型功耗3.8W
根据EN60529和IEC 529，防护等级为IP20。
重量700克（1.5磅）（包装CI867K01，带
CI867和TP867）。
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
表99.Modbus TCP接口CI867-技术规范
CI868和TP867–IEC 61850接口附录A硬件单元
336 3BSE036351-510 A
CI868和TP867–IEC 61850接口
主要特征
•CEX总线模块。
•MPC862P 96MHz。
•带完整性检查的32 MB SDRAM。
•4 MB闪存可编程只读存储器。
•支持全快速以太网的以太网/IEEE 802.3u
10/100Mbps操作。
•支持IEC 61850协议
•10/100 Mbps使用IEEE标准媒体独立
接口（MII）
描述
CI868可用于连接AC 800M控制器
使用IEC 61850协议连接到外部以太网设备。
TP868基板具有两个RJ45以太网连接器，
其中，CH1连接器可以使用10Mbps或100Mbps
（兆比特/秒）。底板有一个密码锁
（见第75页的表4），防止安装
TP867基板上的装置类型不正确。
CI868扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，通过+24 V电源提供适当的电压
CEX巴士。以太网电缆必须通过
以太网交换机。
附录A硬件单元CI868和TP867–IEC 61850接口
3BSE036351-510 A 337
功能框图
图83.方框图——CI868
CI868和TP867–IEC 61850接口附录A硬件单元
338 3BSE036351-510 A
指标
CI868前面板上有六个LED指示灯，指示各种状态
以及CI868上的条件。
技术数据
表100.IEC 61850接口CI868-LED指示器
名称/颜色功能
F（故障）/红色红色F（故障）LED指示CI868上的故障状态。
重置会打开F LED。软件可以打开和关闭它
通过CEX总线控制器中的寄存器。
R（un）/绿色绿色R（un）LED指示灯指示CI868正在运行。
重置关闭LED。软件可以打开LED
并通过CEX总线控制器中的寄存器断开。
RxTx1/黄色：黄色Rx/Tx1 LED旨在点亮以指示
在Ch1接收/发送电报。LED为
由以太网PHY控制。通过复位将其关闭。
RxTx2/黄色：黄色Rx/Tx2 LED（LED将始终切换
关闭）将点亮以指示
在Ch2接收/发送电报（信道为
禁用）。LED由以太网PHY控制。它是
通过复位关闭。
PRIM（ary）：当模块用于单个模块时，PRIM LED点亮
配置（CI868不支持冗余
配置）。
表101.IEC 61850接口CI868-技术规范
项目价值
类型以太网单元
IEC 61850协议
附录A硬件单元CI868和TP867–IEC 61850接口
3BSE036351-510 A 339
IEEE 802.3u 10/100BaseTx中定义的通信速度CH1 10 Mbit/s/100 Mbit/s
状态指示灯正常运行：绿色。
异常故障：红色。
两个交通指示灯–RxTx1和RxTx2（LED将始终亮起
关闭）-由交通速度控制：闪烁黄色
运行为主：黄色。
在冗余配置中运行：黄色。
连接器RJ45
电流消耗（来自CEXBus 24VDC）
典型160 mA（大250 mA）
功耗：典型3.8W（大6W）
根据EN60529和IEC 529，防护等级为IP20。
重量500克（带包装的700克）（带包装的CI868K01
CI868和TP867）。
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
表101.IEC 61850接口CI868-技术规范
CI869和TP869-AF 100接口附录A硬件单元
340 3BSE036351-510 A
CI869和TP869-AF 100接口
主要特征
•CEX总线模块。
•简单的DIN导轨安装
•支持通信接口冗余
•支持与AF 100总线的冗余连接
通过双绞线。
描述
CI869是一个AC 800M通信接口
通过连接到AF 100现场总线的
双绞线（TWP）电缆。
CI869可配置为两种冗余：
电缆和冗余通信接口。
有关的操作和配置的详细信息：
CI869连接到AF 100总线，参见Advant
现场总线100用户手册（3BSE000506*）。
终端板（TP869）包含CEX总线
用于AF 100的连接器和两个4针连接器
TWP。
底板有一个密码锁（见第页的表4
75），防止安装不正确的类型
将装置安装到TP869基板上。
附录A硬件单元CI869和TP869-AF 100接口
3BSE036351-510 A 341
功能框图
指标
th上有六个LED指示灯Status indicators Running normally: Green.
Exceptional fault: Red.
Two traffic indictors – RxTx1 and RxTx2 -- controlled by
traffic pace: Flashing Yellow
Traffic indictor CH2 – RxTx2 - controlled by
traffic pace.
Running as primary: Yellow.
Running in a redundant configuration: Yellow.
Connectors RJ45
Current consumption (from CEXBus 24VDC)
160 mA typical (250 mA max)
Power dissipation 3.8W typical
Protection Rating IP20 according to EN60529, IEC 529.
Weight 700 g (1.5 lb) (package CI867K01with
CI867 and TP867).
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
Table 99. Modbus TCP Interface CI867 - Technical Specification
CI868 and TP867 – IEC 61850 Interface Appendix A Hardware Units
336 3BSE036351-510 A
CI868 and TP867 – IEC 61850 Interface
Key Features
• CEX-Bus Module.
• MPC862P 96MHz.
• 32 MB SDRAM with integrity check.
• 4 MB Flash PROM.
• Ethernet/IEEE 802.3u supporting full Fast Ethernet
10/100Mbps operation.
• Support IEC 61850 protocol
• 10/100 Mbps use IEEE standard Media Independent
Interface (MII)
Description
The CI868 can be used to connect an AC 800M controller
to external Ethernet devices using IEC 61850 protocol.
The TP868 Baseplate has two RJ45 Ethernet connectors,
where CH1 connector can use 10Mbps or 100Mbps
(Mega bits/sec.).The baseplate has a code lock
(see Table 4 on page 75) that prevents the installation of
an incorrect type of unit onto the TP867 Baseplate.
The CI868 expansion unit contains the CEX-Bus logic, a communication unit and a
DC/DC converter that supplies appropriate voltages from the +24 V supply via the
CEX-Bus. The Ethernet cable must be connected to the main network through an
Ethernet Switch.
Appendix A Hardware Units CI868 and TP867 – IEC 61850 Interface
3BSE036351-510 A 337
Functional Block Diagram
Figure 83. Block Diagram – CI868
CI868 and TP867 – IEC 61850 Interface Appendix A Hardware Units
338 3BSE036351-510 A
Indicators
There are six LED indicators on the front panel of CI868 that indicate various states
and conditions on the CI868.
Technical Data
Table 100. IEC 61850 Interface CI868 - LED indicators
Designation/Color Function
F(ault) / Red The red F(ault) LED indicates a fault condition on CI868.
Reset turns the F LED on. Software can turn it on and off
via a register in the CEX-Bus controller.
R(un) / Green The green R(un) LED indicates that CI868 is operational.
Reset turns the LED off. Software can turn the LED on
and off via a register in the CEX-Bus controller.
RxTx1 / Yellow The yellow Rx/Tx1 LED is intended to be lit to indicate a
receiving/transmitting telegram at Ch1. The LED is
controlled by Ethernet PHY. It is turned off by reset.
RxTx2 / Yellow The yellow Rx/Tx2 LED (LED will always be switched
OFF) is intended to be lit to indicate a
receiving/transmitting telegram at Ch2(The channel is
disabled). The LED is controlled by Ethernet PHY. It is
turned off by reset.
PRIM(ary) The PRIM LED is ON when the module is used in a single
configuration (CI868 does not support redundant
configuration).
Table 101. IEC 61850 Interface CI868 - Technical Specification
Item Value
Type Ethernet unit
Protocol IEC 61850
Appendix A Hardware Units CI868 and TP867 – IEC 61850 Interface
3BSE036351-510 A 339
Communication speed CH1 10 Mbit/s / 100 Mbit/s defined in IEEE 802.3u 10/100BaseTx
Status indicators Running normally: Green.
Exceptional fault: Red.
Two traffic indicators – RxTx1 and RxTx2(LED will always be
switched off) -- controlled by traffic pace: Flashing Yellow
Running as primary: Yellow.
Running in a redundant configuration: Yellow.
Connectors RJ45
Current consumption (from CEXBus 24VDC)
160 mA typical (250 mA max)
Power dissipation 3.8W typical (6W max)
Protection Rating IP20 according to EN60529, IEC 529.
Weight 500 g (700g with package) (package CI868K01with
CI868 and TP867).
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
Table 101. IEC 61850 Interface CI868 - Technical Specification
CI869 and TP869 - AF 100 Interface Appendix A Hardware Units
340 3BSE036351-510 A
CI869 and TP869 - AF 100 Interface
Key Features
• CEX-Bus Module.
• Simple DIN rail mounting
• Supports communication interface redundancy
• Supports redundant connections to AF 100 Bus
through twisted wire pair.
Description
The CI869 is an AC 800M communication interface
that connects to the AF 100 field bus through the
twisted pair (TWP) cable.
The CI869 can be configured for both redundant
cables and redundant communication interfaces.
For details about the operation and configuration of
CI869 connected to AF 100 bus, refer to Advant
Fieldbus 100 User Manual (3BSE000506*).
The Termination Plate (TP869) contains the CEX-Bus
connectors and two 4-pin connectors for AF 100
TWP.
The baseplate has a code lock (see Table 4 on page
75) that prevents the installation of an incorrect type
of unit onto the TP869 Baseplate.
Appendix A Hardware Units CI869 and TP869 - AF 100 Interface
3BSE036351-510 A 341
Functional Block Diagram
Indicators
There are six LED indicators on the front panel of CI869. The Mast LED is not used
as CI869 cannot function as bus master. The other LEDs indicate the various states
and conditions of the CI869 unit.