490NAD91105模块备件

名称/颜色功能
F（故障）/红色红色F（故障）LED指示CI869上的故障状态。
复位会打开F LED，直到装置初始化。
R（un）/绿色：绿色R（un）LED指示CI869为
操作的
复位将关闭R LED。
接收/黄色：黄色接收LED指示CI869接收
交通
当通信量为
典型的
当没有总线时，Rx LED闪烁频率较低
检测到流量，在以下情况下以50%以上的频率闪烁
模块具有总线通信量，而设备没有
配置，并在以下情况下以75%以上的频率闪烁
设备已配置，但CDP不正确
民意测验。
复位将关闭Rx LED。
桅杆（er）不使用此LED。
Prim（ary）：黄色Prim（ary）LED指示CI869是
冗余对的主模块。
复位将关闭Prim LED。
双：黄色双模式LED指示冗余
是活动的。
复位将关闭双LED。
附录A硬件单元CI869和TP869-AF 100接口
3BSE036351-510 A 343
技术数据
表103.AF100接口CI869-技术规范
项目价值
AF 100型通信接口
协议先进现场总线100
通信速度TWP 1.5 Mbit/s
状态指示灯正常运行：绿色。
异常故障：红色。
交通指示器——Rx——由交通速度控制：
闪黄
运行为主：黄色。
在冗余配置中运行：黄色。
双绞线连接器（TWP）
电流消耗（来自CEXBus 24VDC）
典型160 mA（大250 mA）
功耗：典型3.8W（大6W）
根据EN60529和IEC 529，防护等级为IP20
重量500克
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）
CI871和TP867–PROFINET IO接口附录A硬件单元
344 3BSE036351-510 A
CI871和TP867–PROFINET IO接口
主要特征
•提供一个10/100 Mbps快速以太网端口
对于PROFINET IO（RJ45连接器位于
在TP867基板上）。
•简单的DIN导轨安装。
•提供与PROFINET IO的通信
通过100 Mbps以太网的协议。
•预设的两字母Alpha码锁定装置
安装在装置底座中，防止
不兼容部件的安装。
•支持热插拔。
描述
CI871可用于连接交流800M
控制器到PROFINET IO设备。
TP867基板有两个RJ45以太网
连接器。CH1连接器支持10 Mbps或
100Mbps。CH2连接器仅支持10 Mbps。
以太网电缆必须通过
以太网交换机。底板有一个密码锁（参见第75页的表4），该密码锁
防止将不正确类型的装置安装到TP867基板上。
CI871扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，从+24 V电源通过
CEX巴士。
默认情况下，CH1连接器用于PROFINET IO，因为它支持100 Mbps。
附录A硬件单元CI871和TP867–PROFINET IO接口
3BSE036351-510 A 345
功能框图
图85.方框图——CI871
CI871和TP867–PROFINET IO接口附录A硬件单元
346 3BSE036351-510 A
指标
CI871前面板上有六个LED指示灯，指示各种状态
以及CI871的条件。
表104.PROFINET IO接口CI871-LED指示器
名称/颜色功能
F（故障）/Red红色F（故障）LED指示CI871上存在故障。
Reset可打开LED。软件可打开和关闭LED
通过CEX总线控制器中的寄存器。
R（un）/绿色：绿色R（un）LED指示CI871为
操作的重置关闭LED。软件可以打开
通过CEX总线中的寄存器打开和关闭LED
控制器。
RxTx1/黄色：黄色Rx/Tx1 LED将点亮以指示
在CH1接收/发送电报。LED为
由以太网PHY控制。通过复位将其关闭。
RxTx2/黄色：黄色Rx/Tx2 LED将点亮以指示
在CH2接收/发送电报。LED为
由以太网PHY控制。通过复位将其关闭。
基本（ary）黄色LED指示模块是否处于活动状态。它
不描述
单元
双：当CI871冗余运行时，LED亮起
配置Designation/Color Function
F(ault) / Red The red F(ault) LED indicates a fault condition on CI869.
A reset turns the F LED ON, till the unit is initialized.
R(un) / Green The green R(un) LED indicates that the CI869 is
operational.
A reset turns the R LED OFF.
Rx / Yellow The yellow Rx LED indicates that the CI869 receives
traffic.
The Rx LED is ON, without flashing, when traffic is
normal.
The Rx LED flashes with less frequency when no bus
traffic is detected, flashes with 50% more frequency when
the module has bus traffic and the device is not
configured, and flashes with 75% more frequency when
the device is configured, but the CDPs are not correctly
polled.
A reset turns the Rx LED OFF.
Mast(er) This LED is not used.
Prim(ary) The yellow Prim(ary) LED indicates that the CI869 is the
primary module of a redundant pair.
A reset turns the Prim LED OFF.
Dual The yellow Dual mode LED indicates that the redundancy
is active.
A reset turns the Dual LED OFF.
Appendix A Hardware Units CI869 and TP869 - AF 100 Interface
3BSE036351-510 A 343
Technical Data
Table 103. AF100 Interface CI869 - Technical Specification
Item Value
Type AF 100 Communication Interface
Protocol Advant Fieldbus 100
Communication speed TWP 1.5 Mbit/s
Status indicators Running normally: Green.
Exceptional fault: Red.
Traffic indicator – Rx -- controlled by traffic pace:
Flashing Yellow
Running as primary: Yellow.
Running in a redundant configuration: Yellow.
Connectors Twisted Pair (TWP)
Current consumption (from CEXBus 24VDC)
160 mA typical (250 mA max)
Power dissipation 3.8W typical (6W max)
Protection Rating IP20 according to EN60529, IEC 529
Weight 500 g
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)
CI871 and TP867 – PROFINET IO Interface Appendix A Hardware Units
344 3BSE036351-510 A
CI871 and TP867 – PROFINET IO Interface
Key Features
• Provides one 10/100 Mbps fast Ethernet port
for PROFINET IO (RJ45 connector located
on the TP867 base plate).
• Simple DIN-rail mounting.
• Provides communication with PROFINET IO
protocol through Ethernet with 100 Mbps.
• Preset, two letter Alpha code locking device
installed in the unit base, which prevents
mounting of incompatible components.
• Supports hot swap.
Description
The CI871 can be used to connect an AC 800M
controller to PROFINET IO devices.
The TP867 Baseplate has two RJ45 Ethernet
connectors. CH1 connector supports 10 Mbps or
100 Mbps. CH2 connector supports only 10 Mbps.
The Ethernet cable must be connected to the PROFINET IO network through an
Ethernet switch. The baseplate has a code lock (refer Table 4 on page 75), which
prevents the installation of an incorrect type of unit onto the TP867 baseplate.
The CI871 expansion unit contains the CEX-Bus logic, a communication unit, and a
DC/DC converter that supplies the required voltage from +24 V supply through the
CEX-Bus.
By default, the CH1 connector is used in PROFINET IO as it supports 100 Mbps.
Appendix A Hardware Units CI871 and TP867 – PROFINET IO Interface
3BSE036351-510 A 345
Functional Block Diagram
Figure 85. Block Diagram – CI871
CI871 and TP867 – PROFINET IO Interface Appendix A Hardware Units
346 3BSE036351-510 A
Indicators
There are six LED indicators on the front panel of CI871 to indicate various states
and conditions of CI871.
Table 104. PROFINET IO Interface CI871 - LED indicators
Designation/Color Function
F(ault) / Red The red F(ault) LED indicates a fault condition on CI871.
Reset turns the LED on. Software can turn it on and off
through a register in the CEX-Bus controller.
R(un) / Green The green R(un) LED indicates that the CI871 is
operational. Reset turns the LED off. Software can turn
the LED on and off through a register in the CEX-Bus
controller.
RxTx1 / Yellow The yellow Rx/Tx1 LED is intended to be ON to indicate a
receiving/transmitting telegram at CH1. The LED is
controlled by Ethernet PHY. It is turned off by reset.
RxTx2 / Yellow The yellow Rx/Tx2 LED is intended to be ON to indicate a
receiving/transmitting telegram at CH2. The LED is
controlled by Ethernet PHY. It is turned off by reset.
PRIM (ary) The yellow LED indicates if the module is active or not. It
does not describe the redundancy configuration of a
module.
DUAL The LED is ON when CI871 is operational in redundant
configuration.