490NAE91100模块备件

项目价值
类型以太网单元
PROFINET IO协议
IEEE 802.3u 10/100中定义的通信速度CH1 10 Mbps/100 Mbps
Base-Tx。
状态指示灯正常运行：绿色。
异常故障：红色。
两个交通指示灯–RxTx1和RxTx2（LED始终亮起
关闭）由交通速度控制：闪烁黄色。
运行为主：黄色。
在冗余配置中运行：黄色。
连接器RJ45
电流消耗
（来自CEX总线24VDC）
典型160 mA（大250 mA）。
功耗通常为3.8瓦（大6瓦）。
根据EN60529和IEC 529，防护等级为IP20。
重量500克（带包装的700克）（带包装的CI871K01
CI871和TP867）。
宽59 x高185 x深127.5毫米。
（宽2.9 x高7.3 x深5.0英寸）。
CI872和TP858-MOD5接口附录A硬件单元
348 3BSE036351-510 A
CI872和TP858-MOD5接口
主要特征
•CEX总线模块
•简单的DIN导轨安装
•支持通信接口冗余
•三个全双工光纤端口
•支持MOD5到MOD5协议
描述
型号为CI872的MOD5通信接口，
将AC 800M控制器连接到MOD5
控制器。
底板有一个代码锁，可防止
将不正确的装置安装到TP858上
底板。
CI872扩展单元包含CEX总线逻辑，
通信单元和DC/DC转换器
从+24 V电源提供适当的电压
通过CEX总线。
CI872只能安装在水平DIN导轨上。基板具有
将金属背板与DIN导轨接触的锁定机构，其
提供有效的接地连接。提供CI872及其基板
作为一个单元（CI872），且无需在
安装程序。要将模块安装在DIN导轨上，必须使用
只有一把平刃螺丝刀。
如果在分离（热插入）后进行装配，请验证钥匙编码是否为
基板和电子模块的情况相同。
附录A硬件单元CI872和TP858-MOD5接口
3BSE036351-510 A 349
功能框图
图86.方框图——CI872
CI872和TP858-MOD5接口附录A硬件单元
350 3BSE036351-510 A
指标
CI872前面板上有六个LED指示灯，指示不同
CI872模块的状态，包括光端口上的通信状态。
技术数据
表106.MOD5接口CI872-LED指示器
名称/颜色功能
F（故障）/Red红色F（故障）LED指示CI872上存在故障。
R（un）/绿色绿色R（un）LED指示灯指示CI872正在运行。
RxTx1/黄色：接收或发送信号时，黄色Rx/Tx1 LED点亮
光信道上的字节–Ch1。
RxTx2/黄色：接收或发送信号时，黄色Rx/Tx2 LED点亮
光信道上的字节–Ch2。
Rx/Tx3/黄色：接收或发送信号时，黄色Rx/Tx3 LED点亮
光信道上的字节–Ch3。
双/黄色：当CI872冗余运行时，黄色双LED点亮
两个CI872之间的配置和工作伙伴关系为：
确立。
表107.MOD5接口CI872-技术规范
项目价值
这是一种光纤连接。
协议MOD5-to-MOD5。
通信速度全双工，速度为500kbps。
附录A硬件单元CI872和TP858-MOD5接口
3BSE036351-510 A 351
状态指示灯正常运行：绿色。
异常故障：红色。
三个交通指示灯——RxTx1、RxTx2和RxTx3-
由交通速度控制：闪烁黄色。
在冗余配置中运行：黄色。
连接器波长：820nm。
光纤尺寸：62.5/125米多模玻璃纤维。
连接器类型：ST-无螺纹。
包括连接器在内的大标称光纤阻尼：11 dB。
电流消耗
（来自CEX总线24VDC）
大124毫安。
功耗大为3.0 W。
根据EN60529和IEC 520，防护等级为IP20。
重量500克（包装为700克）。
宽59 x高185 x深127.5毫米。
（宽2.9 x高7.3 x深5.0英寸）。Item Value
Type Ethernet unit
Protocol PROFINET IO
Communication speed CH1 10 Mbps / 100 Mbps defined in IEEE 802.3u 10/100
Base-Tx.
Status indicators Running normally: Green.
Exceptional fault: Red.
Two traffic indicators – RxTx1 and RxTx2(LED is always
switched off) controlled by traffic pace: Flashing Yellow.
Running as primary: Yellow.
Running in a redundant configuration: Yellow.
Connectors RJ45
Current consumption
(from CEX-Bus 24VDC)
160 mA typical (250 mA max).
Power dissipation 3.8 W typical (6 W max).
Protection Rating IP20 according to EN60529, IEC 529.
Weight 500 g (700 g with package) (package CI871K01 with
CI871 and TP867).
Dimensions W 59 x H 185 x D 127.5 mm.
(W 2.9 x H 7.3 x D 5.0 in).
CI872 and TP858 - MOD5 Interface Appendix A Hardware Units
348 3BSE036351-510 A
CI872 and TP858 - MOD5 Interface
Key Features
• CEX-Bus Module
• Simple DIN rail mounting
• Supports communication interface redundancy
• Three full duplex fiberoptic ports
• Supports MOD5-to-MOD5 protocol
Description
The MOD5 communication interface, type - CI872,
connects the AC 800M controller to the MOD5
controllers.
The baseplate has a code lock that prevents the
installation of an incorrect unit onto the TP858
baseplate.
The CI872 expansion unit contains the CEX-bus logic,
a communication unit, and a DC/DC converter that
supplies appropriate voltages from the +24 V supply
through the CEX-bus.
CI872 should be mounted only on a horizontal DIN- rail. The base plate has a
locking mechanism that contacts the metal back plate to the DIN-rail, which
provides an effective ground connection. The CI872 and its base plate are supplied
as a single unit (CI872), and there is no requirement to separate them during the
mounting procedure. To mount the modules on the DIN-rail, it is necessary to use
only a flat bladed screwdriver.
In case of assembling after a separation (hot insertion), verify that the key coding is
same for the base plate and the electronic module.
Appendix A Hardware Units CI872 and TP858 - MOD5 Interface
3BSE036351-510 A 349
Functional Block Diagram
Figure 86. Block Diagram – CI872
CI872 and TP858 - MOD5 Interface Appendix A Hardware Units
350 3BSE036351-510 A
Indicators
There are six LED indicators on the front panel of CI872 that indicate different
states of the CI872 module including communication on the optical ports states.
Technical Data
Table 106. MOD5 Interface CI872 - LED indicators
Designation/Color Function
F(ault) / Red The red F(ault) LED indicates a fault condition on CI872.
R(un) / Green The green R(un) LED indicates that CI872 is operational.
RxTx1 / Yellow The yellow Rx/Tx1 LED is illuminated when receiving or transmitting a
byte at the optical channel–Ch1.
RxTx2 / Yellow The yellow Rx/Tx2 LED is illuminated when receiving or transmitting a
byte at the optical channel–Ch2.
Rx/Tx3/Yellow The yellow Rx/Tx3 LED is illuminated when receiving or transmitting a
byte at the optical channel–Ch3.
DUAL/Yellow The yellow DUAL LED is illuminated when CI872 is run in redundant
configuration and a working partnership between the two CI872s is
established.
Table 107. MOD5 Interface CI872 - Technical Specification
Item Value
Type Fiber optic connection.
Protocol MOD5-to-MOD5.
Communication speed Full duplex at a speed of 500 Kbps.
Appendix A Hardware Units CI872 and TP858 - MOD5 Interface
3BSE036351-510 A 351
Status indicators Running normally: Green.
Exceptional fault: Red.
Three traffic indicators – RxTx1, RxTx2 and RxTx3 -
controlled by traffic pace: Flashing Yellow.
Running in a redundant configuration: Yellow.
Connectors Wavelength: 820 nm.
Fiber size: 62.5/125 m multimode glass fiber.
Connector type: ST - non threaded.
Max nominal fiber damping including connectors: 11 dB.
Current consumption
(from CEX-bus 24VDC)
Max 124 mA.
Power dissipation Max 3.0 W.
Protection Rating IP20 according to EN60529, IEC 520.
Weight 500 g (700 g with package).
Dimensions W 59 x H 185 x D 127.5 mm.
(W 2.9 x H 7.3 x D 5.0 in).