490NOC00005模块备件

CI873和TP867-以太网/IP接口
主要特征
•CEX总线模块。
•MPC862P 96MHz。
•具有完整性检查的32 Mbps SDRAM。
•4 Mbps闪存PROM。
•以太网/IEEE 802.3u支持全速
以太网10/100Mbps操作。
•支持以太网/IP协议。
•10/100 Mbps使用IEEE标准媒体
独立接口（MII）
描述
CI873可用于连接AC 800M
控制器到外部以太网设备，使用
以太网/IP协议。
TP867基板有两个RJ45以太网
连接器。对于CI873，只有CH1连接器
支持10Mbps/100Mbps。底板具有：
阻止安装的代码锁
TP867基板上的装置类型不正确。
CI873扩展单元包含CEX总线逻辑、通信单元和
DC/DC转换器，从+24 V电源通过
CEX总线。以太网电缆必须通过以下方式连接到主网：
以太网交换机。
附录A硬件单元CI873和TP867-以太网/IP接口
3BSE036351-510 A 353
功能框图
图87.方框图——CI873
CI873和TP867-以太网/IP接口附录A硬件单元
354 3BSE036351-510 A
指标
CI873前面板上有六个LED指示灯，指示各种
CI873上的状态和条件。
表108.以太网/IP接口CI873-LED指示灯
名称/颜色功能
F（故障）/红色：红色F（故障）指示灯指示故障状态为：
CI873.重置会打开LED。软件可以将其打开
通过CEX总线中的寄存器打开和关闭
控制器。
R（un）/绿色：绿色R（un）LED指示CI873为
操作的重置关闭LED。软件可以
通过中的寄存器打开和关闭LED
CEX总线控制器。
RxTx1/黄色：黄色Rx/Tx1 LED将点亮至
在CH1指示接收/发送电报。
LED由以太网PHY控制。转动
通过复位关闭。
RxTx2/黄色：黄色Rx/Tx2 LED（LED将始终切换
断开）旨在打开以指示
在CH2（信道）接收/发送电报
被禁用）。LED由以太网PHY控制。
通过复位将其关闭。
PRIM（ary）：如果此CI873用作a中的主电路，则此LED点亮
冗余配置。
双：当两个CI873都处于
冗余对被同步。LED是
由软件控制。通过复位将其关闭。
附录A硬件单元CI873和TP867-以太网/IP接口
3BSE036351-510 A 355
技术数据
表109.以太网/IP接口CI873-技术规范
项目价值
以太网单元的类型。
以太网/IP协议。
IEEE 802.3u 10/100 Base-Tx中定义的通信速度CH1 10 Mbps/100 Mbps。
状态指示灯正常运行：绿色。
异常故障：红色。
两个交通指示灯–RxTx1和RxTx2（LED将始终亮起
关闭）-由交通速度控制：闪烁黄色
运行为主：黄色。
连接器RJ45。
电流消耗（来自CEXBus 24VDC）
典型160 mA（大250 mA）。
典型功耗为3.8W（大6W）。
根据EN60529和IEC 529，防护等级为IP20。
重量500克（带包装的700克）（带包装的CI873K01
CI873和TP867）。
尺寸宽59 x高185 x深127.5 mm
（宽2.9 x高7.3 x深5.0英寸）CI873 and TP867 - EtherNet/IP Interface
Key Features
• CEX-Bus Module.
• MPC862P 96MHz.
• 32 Mbps SDRAM with integrity check.
• 4 Mbps Flash PROM.
• Ethernet/IEEE 802.3u supporting full Fast
Ethernet 10/100Mbps operation.
• Supports EtherNet/IP protocol.
• 10/100 Mbps use IEEE standard Media
Independent Interface (MII)
Description
The CI873 can be used to connect an AC 800M
controller to external Ethernet devices using the
EtherNet/IP protocol.
The TP867 Baseplate has two RJ45 Ethernet
connectors. For CI873, only the CH1 connector that
supports 10 Mbps/100 Mbps is used.The baseplate has
a code lock which prevents the installation of an
incorrect unit type onto the TP867 Baseplate.
The CI873 expansion unit contains the CEX-Bus logic, a communication unit and a
DC/DC converter that supplies appropriate voltages from the +24 V supply through
the CEX-Bus. The Ethernet cable must be connected to the main network through
an Ethernet Switch.
Appendix A Hardware Units CI873 and TP867 - EtherNet/IP Interface
3BSE036351-510 A 353
Functional Block Diagram
Figure 87. Block Diagram – CI873
CI873 and TP867 - EtherNet/IP Interface Appendix A Hardware Units
354 3BSE036351-510 A
Indicators
There are six LED indicators on the front panel of CI873 that indicate the various
states and conditions on the CI873.
Table 108. EtherNet/IP Interface CI873 - LED indicators
Designation/Color Function
F(ault) / Red The red F(ault) LED indicates a fault condition on
CI873. Reset turns the LED ON. Software can turn it
On and OFF through a register in the CEX-Bus
controller.
R(un) / Green The green R(un) LED indicates that the CI873 is
operational. Reset turns the LED OFF. Software can
turn the LED ON and OFF through a register in the
CEX-Bus controller.
RxTx1 / Yellow The yellow Rx/Tx1 LED is intended to be ON to
indicate a receiving/transmitting telegram at CH1.
The LED is controlled by Ethernet PHY. It is turned
OFF by reset.
RxTx2 / Yellow The yellow Rx/Tx2 LED (LED will always be switched
OFF) is intended to be ON to indicate a
receiving/transmitting telegram at CH2 (The channel
is disabled). The LED is controlled by Ethernet PHY.
It is turned OFF by reset.
PRIM(ary) This LED is ON if this CI873 acts as the primary in a
redundant configuration.
DUAL The yellow DUAL LED is ON when both CI873’s in a
redundant pair are synchronized. The LED is
controlled by software. It is turned OFF by reset.
Appendix A Hardware Units CI873 and TP867 - EtherNet/IP Interface
3BSE036351-510 A 355
Technical Data
Table 109. EtherNet/IP Interface CI873 - Technical Specification
Item Value
Type Ethernet unit.
Protocol EtherNet/IP.
Communication speed CH1 10 Mbps / 100 Mbps defined in IEEE 802.3u 10/100 Base-Tx.
Status indicators Running normally: Green.
Exceptional fault: Red.
Two traffic indicators – RxTx1 and RxTx2(LED will always be
switched off) -- controlled by traffic pace: Flashing Yellow
Running as primary: Yellow.
Connectors RJ45.
Current consumption (from CEXBus 24VDC)
160 mA typical (250 mA max).
Power dissipation 3.8W typical (6W max).
Protection rating IP20 according to EN60529, IEC 529.
Weight 500 g (700g with package) (package CI873K01with
CI873 and TP867).
Dimensions W 59 x H 185 x D 127.5 mm
(W 2.9 x H 7.3 x D 5.0 in)