490NRP95400模块备件

CI873和TP867-以太网/IP接口
传输异步、全/半双工/单工
电源：24伏直流电（小12伏直流电-大36伏直流电）
功耗3W
尺寸55 x 100 x 128毫米（2.2 x 3.9 x 5.0英寸）
重量400克（0.9磅）
表125.传输距离（电缆0.3 mm2
/42 pF/m）
米（码）位/秒
1000 ( 1094) 19200
2500 ( 2734) 9600
5000 ( 5468) 4800
8000 ( 8749) 2400
12000 (13123) 1200
18000 (19685) 600
SB821外部电池–AC 800M内存备份附录A硬件单元
392 3BSE036351-510 A
SB821外部电池–AC 800M内存备份
描述
使用SB821电池单元
作为外部电源
为AC 800M控制器提供扩展内存备份。
该装置采用DIN导轨安装
并设有单独的
连接电缆（TK821V020），
2米（2.2码）长。
SB821
!
SB821 3.6V锂电池组
注意警告
电池上的文字。
X1
B–B+SH
附录A硬件单元SB821外部电池–AC 800M内存备份
3BSE036351-510 A 393
技术数据
表126.SB821–外部电池数据
项目价值
电池类型低倍率锂，
3.6V，16Ah
尺寸ANSI尺寸D
IEC尺寸R20
锂含量：5.6克（0.18盎司）
备份时间：请参阅PM8xx装置的数据
尺寸宽85.6 x长51 x高136 mm
（3.4 x 2 x 5.4英寸）
重量600克（1.3磅）（装有SB821、电池和
TK821V020）
根据EN60529和IEC 529，防护等级为IP20
SB822可充电外部电池–AC 800M内存备份附录A硬件单元
394 3BSE036351-510 A
SB822可充电外部电池–AC 800M内存
后备
描述
使用SB822电池单元
作为
外部电源至
提供
扩展内存备份
这个
AC 800M控制器。单位为：
DIN导轨安装和提供
具有
单独的连接电缆
（TK821V020）2米（2.2码）英寸
长
附录A硬件单元SB822可充电外部电池–AC 800M内存备份
3BSE036351-510 A 395
技术数据
表127.SB822–可充电外部电池数据
项目价值
电池类型可充电锂离子
3.75V 2.3Ah
电池尺寸棱柱形14.5x43x50 mm
锂当量含量0.8g
备份时间：请参阅PM8xx装置的数据
尺寸宽85.6 x长51 x高136 mm
（3.4 x 2 x 4.4英寸）
重量600克（1.3磅）（装有SB822、电池和
TK821V020）
根据EN60529，防护等级为IP20
使用SB822外部电池单元时，将内部电池从
作为状态监控的处理器单元仅为一个电池提供。
DIN导轨–TS 35/7.5附录A硬件单元
396 3BSE036351-510 A
DIN导轨–TS 35/7.5
下图显示了DIN导轨TS的外形和尺寸，单位为mm（in.）
35/7.5.
正常供应长度为2米（6.6英尺）（符合标准DIN 46 277，EN 50 022）。
图112 DIN导轨TS 35/7.5–尺寸
15 10
27
7.5
6 35
(0.6”)
(1.4”) (1.1”) (0.2”)
(0.3”)
7.5
(0.3”)
(0.4”)
附录A硬件单元杂项设备
3BSE036351-510 A 397
各种各样的设备
CEX总线的TB850终端（公型）
图113.用于CEX的TB850终端（公端）
终结者
TB850
CEX总线TB850终端（公）附录A硬件单元
398 3BSE036351-510 A
图114.使用冗余通信接口时的CEX总线终端
单元（带BC810）和控制器
BC810
BC810
RCU链路
电缆
PM861A/PM864A/PM865
PM861A/PM864A/PM865
终结者
TB850
终结者
TB850
附录A硬件单元TB851 CEX总线终端（母型）
3BSE036351-510 A 399
用于CEX总线的TB851终端（母型）
当TK850分机时，需要CEX总线的TB851（母）终端
使用电缆。
图115.CEX总线的TB851终端（母型）
TK850电缆
终结者
TB851
TB807模块总线终端插头附录A硬件单元
400 3BSE036351-510 A
TB807模块总线终端插头
终端插头必须始终安装在模块总线的后一个I/O单元上。
如果模块总线上未使用任何单元，则不需要总线终端。不
冗余CPU配置中需要模块总线终端。
TB852 RCU链路终端插头
当PM861/PM864时，需要TB852 RCU链路终端插头
处理器单元以单一配置运行。
TB853 RCU控制链路终端插头
PM891时需要TB853 RCU控制链路终端插头
处理器单元以单一配置运行。它与RCU控制装置相连
PM891装置顶部的端口。
TK850 CEX总线延长电缆
0.7米（2.3英尺）延长电缆，配有连接器（DB25P型金属
外壳）提供与相邻之间通信接口单元的连接
DIN导轨。它始终用于冗余CPU配置，用于连接
两个处理器单元之间的CEX总线。
TK851 RCU链路电缆
冗余控制单元链路电缆用于从传输日志数据
主CPU连接到备用CPU，并交换状态和控制信息
在主CPU和备份CPU之间。RCU链路使用68极连接器，
其中一个标记为“上部”。连接到此连接器的CPU将：
定义为控制生成器和操作员站中的上层CPU。
RCU链路CaTransfer Asynchronous, full/half duplex/simplex
Power Supply 24 V DC (Min. 12 V DC – Max 36 V DC)
Power Consumption 3 W
Dimensions 55 x 100 x 128 mm (2.2 x 3.9 x 5.0 in.)
Weight 400 g (0.9 lb)
Table 125. Transfer Distance (Cable 0.3 mm2
/42 pF/m)
Meters (yd.) bit/s
 1000 ( 1094) 19200
 2500 ( 2734) 9600
 5000 ( 5468) 4800
 8000 ( 8749) 2400
12000 (13123) 1200
18000 (19685) 600
SB821 External Battery – AC 800M Memory Back-up Appendix A Hardware Units
392 3BSE036351-510 A
SB821 External Battery – AC 800M Memory Back-up
Description
The SB821 battery unit is used
as an external power supply to
provide extended memory backup for the AC 800M Controller.
The unit is DIN-rail mounted
and provided with a separate
connecting cable (TK821V020),
2 m (2.2 yd.) in length.
SB821
!
SB821 3.6V Lithium Battery Unit
Note the warning
text on the battery.
X1
B– B+ SH
Appendix A Hardware Units SB821 External Battery – AC 800M Memory Back-up
3BSE036351-510 A 393
Technical Data
Table 126. SB821 – External battery data
Item Value
Battery Type Low rate lithium,
3.6 V, 16 Ah
Size ANSI size D
IEC size R20
Lithium content 5.6 g (0.18 oz.)
Back-up-time See data for the PM8xx unit
Dimensions W 85.6 x D 51 x H 136 mm
(3.4 x 2 x 5.4 in)
Weight 600 g (1.3 lb) (package with SB821,battery and
TK821V020)
Protection Rating IP20 according to EN60529, IEC 529
SB822 Rechargeable External Battery – AC 800M Memory Back-up Appendix A Hardware Units
394 3BSE036351-510 A
SB822 Rechargeable External Battery – AC 800M Memory
Back-up
Description
The SB822 battery unit is used
as an
external power supply to
provide
extended memory back-up for
the
AC 800M Controller. The unit is
DIN-rail mounted and provided
with
a separate connecting cable
(TK821V020) 2 m (2.2 yd.) in
length.
Appendix A Hardware Units SB822 Rechargeable External Battery – AC 800M Memory Back-up
3BSE036351-510 A 395
Technical Data
Table 127. SB822 – Rechargeable External battery data
Item Value
Battery type Rechargeable Lithium-Ion
3.75V 2.3 Ah
Battery size Prismatic 14.5x43x50 mm
Lithium equivalent content 0.8g
Back-up-time See data for the PM8xx unit
Dimensions W 85.6 x D 51 x H 136 mm
(3.4 x 2 x 4.4 in)
Weight 600 g (1.3 lb) (package with SB822,battery and
TK821V020)
Protection Rating IP20 according to EN60529
When using the SB822 external battery unit, remove the internal battery from the
processor unit as status monitoring is only provided for one battery.
DIN-Rail – TS 35/7.5 Appendix A Hardware Units
396 3BSE036351-510 A
DIN-Rail – TS 35/7.5
The figure below shows the profile and dimensions in mm (in.) of the DIN-rail TS
35/7.5.
Normal supplied length is 2 m (6.6 ft.) (to standard DIN 46 277, EN 50 022).
Figure 112. DIN-rail TS 35/7.5 – Dimensions
15 10
27
7.5
6 35
(0.6”)
(1.4”) (1.1”) (0.2”)
(0.3”)
7.5
(0.3”)
(0.4”)
Appendix A Hardware Units Miscellaneous Equipment
3BSE036351-510 A 397
Miscellaneous Equipment
TB850 Terminator for CEX-Bus (Male)
Figure 113. TB850 Terminator for CEX (male)
Terminator
TB850
TB850 Terminator for CEX-Bus (Male) Appendix A Hardware Units
398 3BSE036351-510 A
Figure 114. CEX-Bus Terminator when using Redundant Communication Interface
Units (with BC810) and Controllers
BC810
BC810
RCU Link
Cables
PM861A/PM864A/PM865
PM861A/PM864A/PM865
Terminator
TB850
Terminator
TB850
Appendix A Hardware Units TB851 Terminator for CEX-Bus (Female)
3BSE036351-510 A 399
TB851 Terminator for CEX-Bus (Female)
A TB851 (female) Terminator for CEX-Bus is required when a TK850 extension
cable is used.
Figure 115. TB851 Terminator for CEX-Bus (female)
TK850 Cable
Terminator
TB851
TB807 ModuleBus Terminator Plug Appendix A Hardware Units
400 3BSE036351-510 A
TB807 ModuleBus Terminator Plug
The Terminator plug must always be mounted on the last I/O unit of the ModuleBus.
If no units are used on the ModuleBus, no bus termination is required. No
ModuleBus termination is required in redundant CPU configuration.
TB852 RCU Link Terminator Plug
The TB852 RCU Link Terminator Plug is required when the PM861/PM864
processor unit operates in single configuration.
TB853 RCU Control Link Terminator Plug
The TB853 RCU Control Link Terminator Plug is required when the PM891
processor unit operates in single configuration. This is plugged to the RCU Control
port at the top of the PM891 unit.
TK850 CEX-Bus Extension Cable
A 0.7 m (2.3 ft.) extension cable, complete with connector (type DB25P-metal
housing) provides connectivity to Communication Interface units between adjacent
DIN-rails. It is always used in redundant CPU configuration for connecting the
CEX-Bus between the two processor units.
TK851 RCU Link Cable
The Redundant Control Unit Link Cable is used to transfer log data from the
Primary CPU to the Backup CPU, and to exchange status and control information
between the Primary and Backup CPUs. The RCU Link uses 68-pole connectors,
one of which is labeled “UPPER”. The CPU connected to this connector will be
defined as the upper CPU in the Control Builder and Operator Station.
The RCU Link Cable is also used as interconnection cable between two BC810.
Appendix A Hardware Units TK853
3BSE036351-510 A 401
TK853
Technical Data
TK855 RCU Data Link Cable
The TK855 Redundant Control Unit Data Link Cable, connected between
redundant PM891 units, transfers the data required to keep the backup PM891
synchronized with the primary PM891.
Table 128. TK853 – Technical Data
Item Value
Connectors • One 9-pole male D-sub (DE9P)
• One 8-pole RJ45 plug
Weight 100 g (0.2 lb) (TK853V02)
Length 2.0 m (6.56’) (TK853V02)
Figure 116. TK853 – Cable Characteristics
7 RTS
4 DTR
3 TD
5 0 V
2 RD
1 DCD
8 CTS
Shield
AC 800M
RJ45 plug
Modem
Male 9-pole,
D-sub connector (DE9P)
RTS
DTR
TD
0 V
0 V
RD
DCD
CTS
Shield
1
2
3
4
5
6
7
8
TK856 RCU Control Link Cable Appendix A Hardware Units
402 3BSE036351-510 A
TK856 RCU Control Link Cable
The TK856 Redundant Control Unit Control Link Cable, connected between
redundant PM891 units, provides role selection and CPU identity assignment
(UPPER/LOWER).
TK212A Tool Cable
Technical Data
Table 129. TK212A Tool Cable – Technical Data
Item Value
Connectors • One 9-pole female D-type
• One 8-pole RJ45 plug
Weight 125 g (0.3 lb)
Length 3.0 m (9.84’)
Figure 117. TK212A – Cable Characteristics
8 CTS
6 DSR
2 RD
1 DCD
5 0 V
3 TD
4 DTR
7 RTS
Shield
AC 800M
RJ45 plug
PC
Female 9-pin,
D-type connector
RTS
DTR
TD
0 V
0 V
RD
DCD
CTS
Shield
1
2
3
4
5
6
7
8
Appendix A Hardware Units Al-Profile Support For DIN-Rail
3BSE036351-510 A 403
Al-Profile Support For DIN-Rail
Units comprising the AC 800M controller are mounted onto DIN-rails (type: TS
35/7.5). However, the DIN-rail itself is not rigid enough to support the units on its
own. For this reason a support is recommended, such as an A1-profile, specifically
designed for supporting DIN-rails (see Figure 118 on page 403 and Figure 119 on
page 404).
Key features of the Al-profile are:
• Simple mounting.
• No drilling required; profile incorporates pre-formed channels suitable for selftapping screws.
• Provides secure mounting in locations subject to extreme vibration,
see Figure 18 on page 69.
• Rigid construction.
• Easy-fit, press-in cable-retaining duct