490NTC00015模块备件

CI873和TP867-以太网/IP接口
缆绳
外面的
直径
英寸（mm）
终止
电阻
()
室内的
安装
导体/
特设工作组
介电电压
环境的
临时雇员
评级
(C）
NEC
评级
导管2/#22 30 60 CL2（1）中的Taylor 6201C.35（8.89）150
（1） 额定为CL2的电缆可以进入电缆槽。
B3078F（2）
（2） B代表贝尔登。
.385（9.78）150电缆槽（3）
（3） 也可用于室外电缆桥架。
2/#22 300 75 PLTC/CM
A9823C（4）
（4） A代表阿尔法。
导管2/#22 30 60 CL2中的.35（8.89）150
C4596（5）
（5） C代表合并。
导管2/#22 30 60中的.35（8.89）150
B89182.308（7.82）150在增压室2/#22 150 200 CL2P
B9207.33（8.38）100（6）
（6） 如果需要端接，请使用CI862上的110欧姆选项（参见124页的总线端接）。
导管2/#20 300 75 CM内
B89207.267（6.78）100（6）增压室2/#20 150 200 CMP
A4794.282（7.16）100（6）增压室2/#20 150 200
B9815.33（8.38）100（6）直埋2/#20 80无
B9855.270（6.86）100（6）导管4/#22 150 60 CM/MP
B89696.264（6.71）100（6）在增压室4/#22 150 200 CMP/MPP
B89855.240（6.10）100（6）在增压室4/#22 150 200 CMP/MPP
B9463.243（6.17）75导管2/#20 300 80 CM
A9814.243（6.17）75导管2/#22 150 60厘米
B9302.244（6.2）导管4/#22 300 80 CM
附录C推荐部件推荐部件
3BSE036351-510 A 425
推荐部件附录C推荐部件
426 3BSE036351-510 A
3BSE036351-510 A 427
附录D指令注意事项
相关产品符合EMC指令EMCD 2004/108/EC和低
电压指令LVD 2006/95/EC。产品具有CE标志。
电磁兼容性（EMC）
本文件中提到的模块，其产品或包装为CE
根据以下标准进行测试和批准：
•EN 61131-2可编程控制器产品标准
-工业环境
•EN 61000-6-4 EMC–通用排放标准，
4部分——工业环境
•EN 61000-6-2 EMC–通用抗扰度标准，
2部分——工业环境。
低压指令（LVD）
本手册中提到的模块，产品或包装均标有CE标志，
如适用，遵守LVD。
为了实现AC 800M和S800 I/O的LVD，电源应提供
二次安全超低电压（SELV）或受保护超低电压
（骨盆）。本手册中描述的SD82X和SD83X电源满足
有关这些要求，请参见上的电源装置-SD821、SD822和SD823型
低压指令（LVD）附录D指令注意事项
428 3BSE036351-510 A
356页和电源装置-上的SD831、SD832、SD833和SD834型
363页。
如果使用除SD82X和SD83X以外的其他电源提供24V
d、 c.对于AC 800M，要求其也具有CE标志，保险商
实验室（UL）列出并满足LVD（SELVandPELV）标准。
AC 800M模块为IP20半保护设备，必须安装
在非公共场所。
3BSE036351-510 A 429
附录E标准
以下信息适用于批准用于危险场所的产品
根据CSA和/或UL标准UL60079-15（2002）。
危险场所批准
为了符合CSA和/或UL认证，以便在危险场所使用
以下信息与CSA和/或UL认证的ABB industrial相关：
控制产品。
•标有I类、2区、AEx nC IIC、危险的设备
适用于I类、2区、AEx nC IIC或非危险区域的位置
仅限位置。
•标有I类、2区、AEx nC IIC、危险的设备
位置和安装在I类2区AEx nC IIC危险区域
位置需要具有入口防护等级的整体外壳或机柜
低防护等级为IP54。外壳应能承受冲击
小7焦耳，仅允许在污染等级为2的情况下安装
环境或更低。
•标有I类、2区、AEx nC IIC、危险的设备
位置和安装在I类2区AEx nC IIC危险区域
位置要求采取措施，以防止以下情况的瞬态干扰：
超过额定电压的40%。
爆炸危险-替换部件可能会损害I类的适用性，
区域2。
爆炸危险-除非电源已切换，否则不要更换电池
关闭或该区域已知为非危险区域。
危险场所批准附录E标准
430 3BSE036351-510 A
爆炸危险-除非电源已断开，否则不要断开设备
关闭或该区域已知为非危险区域。
3BSE036351-510 A 431
附录F环境数据
AC 800M产品的环境数据
产品对运行期间遇到的环境因素的免疫力，
本节概述了运输和储存。
工业环境由高压或中压变压器供电，该变压器专用于供应装置、馈电、制造或
类似的植物。存在Cable Outer Diameter in (mm) Terminating Resistor () Indoor Installation Conductors / AWG DiElectric Voltage Ambient Temp. Rating (C) NEC Rating Taylor 6201C .35 (8.89) 150 in conduit 2 / #22 30 60 CL2(1) (1) Cables rated CL2 can go into a wire tray. B3078F(2) (2) B stands for Belden. .385 (9.78) 150 cable tray(3) (3) Can also be used in cable tray outdoors. 2 / #22 300 75 PLTC/CM A9823C(4) (4) A stands for Alpha. .35 (8.89) 150 in conduit 2 / #22 30 60 CL2 C4596(5) (5) C stands for Consolidated. .35 (8.89) 150 in conduit 2 / #22 30 60 B89182 .308 (7.82) 150 in plenum 2 / #22 150 200 CL2P B9207 .33 (8.38) 100(6) (6) Use the 110 ohm option on the CI862 if termination is required (see Bus Termination on page 124). in conduit 2 / #20 300 75 CM B89207 .267 (6.78) 100(6) in plenum 2 / #20 150 200 CMP A4794 .282 (7.16) 100(6) in plenum 2 / #20 150 200 B9815 .33 (8.38) 100(6) direct burial 2 / #20 80 NONE B9855 .270 (6.86) 100(6) in conduit 4 / #22 150 60 CM/MP B89696 .264 (6.71) 100(6) in plenum 4 / #22 150 200 CMP/MPP B89855 .240 (6.10) 100(6) in plenum 4 / #22 150 200 CMP/MPP B9463 .243 (6.17) 75 in conduit 2 / #20 300 80 CM A9814 .243 (6.17) 75 in conduit 2 / #22 150 60 CM B9302 .244 (6.2) in conduit 4 / #22 300 80 CM Appendix C Recommended Components Recommended Components 3BSE036351-510 A 425 Recommended Components Appendix C Recommended Components 426 3BSE036351-510 A 3BSE036351-510 A 427 Appendix D Directive Considerations Relevant products comply with EMC Directive EMCD 2004/108/EC and Low Voltage Directive LVD 2006/95/EC. The products are provided with a CE marking. Electro-Magnetic Compatibility (EMC) Modules mentioned in this document, for which the product or packing is CE marked, are tested and approved according to the following standards: • EN 61131-2 Product Standard, Programmable Controller - Industrial Environment • EN 61000-6-4 EMC – Generic Emission Standard, Part 4 – Industrial Environment • EN 61000-6-2 EMC – Generic Immunity Standard, Part 2 – Industrial Environment. Low-Voltage Directive (LVD) Modules mentioned in this manual, for which product or packing is CE marked, comply with the LVD where applicable. To fulfill the LVD for AC 800M and S800 I/O, the power supplies shall provide a secondary Safety Extra Low Voltage (SELV) or a Protected Extra Low Voltage (PELV). The power supplies described in this manual, SD82X and SD83X, fulfill these requirements, see Power Supply Units – Types SD821, SD822 and SD823 on Low-Voltage Directive (LVD) Appendix D Directive Considerations 428 3BSE036351-510 A page 356and Power Supply Units - Types SD831, SD832, SD833, and SD834 on page 363. If you use other power supplies, except SD82X and SD83X, to provide the 24V d.c. for AC 800M it is required that they also are CE marked, Underwriters Laboratories (UL ) listed and fulfill the LVD (SELVandPELV) criteria. The AC 800M modules are IP20 semi-protected equipment and must be mounted in non-public localities. 3BSE036351-510 A 429 Appendix E Standards The information below is applicable to products approved for hazardous locations according to CSA and/or UL standard UL60079-15 (2002). Hazardous Location Approval To comply with CSA and/or UL certification for use at hazardous locations, the following information is relevant for CSA and/or UL-certified ABB industrial control products. • Equipment labeled with reference to Class I, Zone 2, AEx nC IIC, hazardous locations is suitable for use in Class I, Zone 2, AEx nC IIC, or non-hazardous locations only. • Equipment labeled with reference to Class I, Zone 2, AEx nC IIC, hazardous locations and is to be mounted in Class I, Zone 2, AEx nC IIC, hazardous locations requires an overall enclosure or cabinet with ingress protection rating of IP54 as a minimum. The enclosure shall be capable to withstand an impact of minimum 7 joule and installation is only allowed in pollution degree 2 environment or lower. • Equipment labeled with reference to Class I, Zone 2, AEx nC IIC, hazardous locations and is to be mounted in Class I, Zone 2, AEx nC IIC, hazardous locations requires that provisions are made to prevent transient disturbances of more than 40% of rated voltage. Explosion hazard - Substitution of components may impair suitability for Class I, Zone 2. Explosion hazard - Do not replace batteries unless the power has been switched off or the area is known to be non-hazardous. Hazardous Location Approval Appendix E Standards 430 3BSE036351-510 A Explosion hazard - Do not disconnect equipment unless the power has been switched off or the area is known to be non-hazardous. 3BSE036351-510 A 431 Appendix F Environmental Data Environmental Data for AC 800M Products The immunity of products to environmental factors met during operation, transportation and storage is summarized in this section. Industrial environment are supplied with power from a high-voltage or mediumvoltage transformer dedicated to supplying installations feeding manufacturing or similar plants. The existence of industrial apparatus and heavy, frequently-switched inductive or capacitive loads characterize an Industrial environment. The associated magnetic fields are high. Control products incl. I/O-systems are normally intended for Industrial environment. Products manufactured by ABB and other companies are normally type-tested or evaluated to ensure compliance with the environmental standards specified below. Environmental specifications applicable to peripheral equipment, for example printers, may differ. Please refer to the relevant product data sheets. The degree to which the units resist environmental influence depends on their components and design. System enclosures, cable types and how these are routed determine the environmental specification of the entire system.