490NTW00002模块备件

CI873和TP867-以太网/IP接口
测试和操作工艺时，工艺技术人员应在场
物体。
•如果存在不确定性，切勿激活任何系统初始化按钮
存在关于初始化期间系统内发生的情况。
总是先检查。
•始终记住，控制系统可以通过
远程工程站，通过控制连接到另一个节点
网络
•记住，AC 800M控制器将在电压
应用。
采取步骤使流程处于安全状态，提高了
电源、通信链路或控制系统部件时的安全
失败例如，这些步骤可能需要安装阀门或继电器
自动返回到故障安全位置。
产品安全
必须始终遵守以下安全规则：
•为避免静电放电，将自己和任何工具接地
在处理印刷电路板、电池、存储卡和其他
设备的敏感部件
•所有电子设备对ESD（静电放电）敏感。到
在处理印刷电路板时避免意外损坏，它是
建议佩戴腕带，接地至底盘。皮带必须
具有内置保护电阻器
•储存和运输时必须使用防静电导电塑料袋
运输中的PC板。
16 3BSE036351-510 A
安全总结
更换单元前
维修
更换装置的所有程序可通过参考相关
文档
在连接系统电源的情况下拆卸或更换单元可能会导致以下人员受伤：
人员和设备损坏。因此，这是极其重要的
拆除前，在工艺侧完全断开电源
或者发生单元的插入。
参见198页的在线更换装置和I/O文件。
建议保持适当的备件库存，以：
避免系统停机。
确保当前应用程序的备份副本在
以避免系统停机。
3BSE036351-510 A 17
安全总结（续）
操作环境
在AC 800M控制器系统上线之前，调查
环境条件适用。特别注意到：
如下：
•控制器不得暴露在超过给定值的条件下
在相关技术规范中。
•控制器不得在暴露于强电的环境中使用
干扰电机会产生超过水平的干扰
允许用于设备，例如在维修工作期间。
•所有产品必须在以下方面采取适当的预防措施：
静电损坏。
•控制器不得暴露在阳光直射下。
重要软件检查
•使用系统的故障监测设施来防止事故或灾难。
•当有疑问时，在执行变更前始终进行检查。
重要硬件通知
•在任何情况下，不得断开电源
正常运行的系统。始终使用正确的系统关机
断开电源前的步骤。
电缆引起的信号噪声
可能引起电气干扰的电缆（例如，电源电缆）
不得安装在传输快速数字信号的总线电缆附近。确保
安装在内部的电缆之间的小距离为10厘米（4英寸）
橱柜。
危险电源
操作和维护程序，在此期间，人员可能会进入
接触高压时，只能由经过充分培训的人员进行
这些环境中电气设备的维护，以及
充分意识到所涉及的所有风险。Process technicians are to be present when testing and operating process
objects.
• Never activate any System Initialization push-button if any uncertainty
exists regarding exactly what occurs within the system during initialization.
ALWAYS CHECK FIRST.
• Remember at all times, that the control system can be controlled from a
remote engineering station, connected at another node via Control
Network.
• Remember, the AC 800M Controller will start automatically when voltage
is applied.
Taking steps to bring the process to a safe state, provides an improved level of
safety when power supplies, communication links or parts of the control system
fail. Such steps may require, for example, the installation of valves or relays that
automatically return to a fail-safe position.
Product Safety
The following safety rules must be observed at all times:
• To avoid discharging static electricity, ground both yourself and any tools
before handling printed circuit boards, batteries, memory cards, and other
sensitive pieces of the equipment
• All electronic devices are sensitive to ESD (electrostatic discharge). To
avoid accidental damage while handling printed circuit boards, it is
recommended to wear a wrist strap, grounded to the chassis. The strap must
have a built-in protective resistor
• Anti-static, conductive plastic bags must be used for storage and transport
of PC boards in transit.
16 3BSE036351-510 A
Safety Summary
Before replacing Units
Maintenance
All procedures for replacing units can be located by referring to the relevant
documentation.
Removing or replacing units with system power connected can cause injury to
personnel and damage to equipment. It is, therefore, of the utmost importance
that the power supply be fully disconnected, on the process side, before removal
or insertion of units takes place.
See Online Replacement of Unit on page 198 and I/O documentation.
It is recommended that a stock of suitable spare components be maintained to
avoid system downtime.
Ensure that back-up copies of the current application program are made at
regular, predetermined intervals to avoid system downtime.
3BSE036351-510 A 17
Safety Summary (continued)
Operating Environment
Before the AC 800M Controller system is brought online, investigate which
environmental conditions are applicable. Take note in particular of the
following:
• The controller must not be exposed to conditions that exceed the values given
in the relevant technical specifications.
• The controller must not be used in an environment exposed to strong electrical
interference. Electrical machines can produce interference that exceeds levels
permitted for the equipment, for example during repair work.
• All products must be handled with appropriate precautions with regard to
electrostatic damage.
• The controller must not be exposed to direct sunlight.
Important Software Check
• Use the system’s fault-monitoring facilities to prevent accidents or mishaps.
• When in doubt, ALWAYS CHECK before executing changes.
Important Hardware Notice
• DO NOT, under any circumstances, disconnect the power supply to a
normally functioning system. Always use the correct system shut-down
procedure prior to disconnecting the power supply.
Signal Noise Due to Cables
Cables which may cause electrical interference (for example, power supply cables)
must not be installed adjacent to bus cables carrying fast digital signals. Ensure that
a minimum distance of 10 cm (4 in.) is provided between cables installed inside
cabinets.
Hazardous Electrical Supplies
Operational and maintenance procedures, during which personnel may come into
contact with high voltage, should only be carried out by personnel fully trained in
the maintenance of electrical equipment within those environments, and who are
fully aware of all risks involved.