490NTW00005模块备件

CI873和TP867-以太网/IP接口
具体的
警告
（续）
76页：不要操作锁定装置。ABB对因操作锁定装置而导致的错误概不负责。
-79和92页：不要将内部备用电池放在电池中
保持架，直到AC 800M控制器正常通电，以及
内存备份功能已激活，即B（电池）
LED闪烁。如果没有正常电源连接到处理器单元
电池就位后，CPU内存将立即开始
消耗电池电量。
90页：请注意，在冗余CPU配置中，不能使用COM3和基板上的电气模块总线。
91页：请注意，必须使用且不能使用RCU链路电缆TK851
用类似的电缆代替。使用其他电缆将禁用CB和操作员站中CPU的识别。在单一配置中运行时，RCU链路电缆TK851可能暂时用于：
执行终端插头的功能。
98页：不要连接两个CEX总线段，用
BC810通过CEX总线扩展电缆TK850相互连接。
98页：在AC 800M高完整性控制器中，需要连接BC810的外部电源输入，并且电源为
根据图33或图34严格配置
也不允许通过以下方式更改配置：
模块之间的单独断路器。
99页：位于主或单控制器CPU旁边的BC810的热插拔（也称为“直接BC810”）可能会危及整个系统
控制器，除非
CEX总线处于非运行状态。注：在AC 800M HI控制器中
这是无条件和故意导致控制器停机。
112页：不可能通过热插拔更换CI851单元，并且
不允许在包含CI851的系统中执行固件的在线升级。
3BSE036351-510 A 21
安全总结（续）
具体的
警告
（续）
114页：不可能通过热插拔更换CI852单元，并且
不允许在包含CI852的系统中执行固件的在线升级。
118页：CI854A（非CI854）支持热插拔。
133页：110-120伏交流电压为-115伏，220-240伏交流电压则为230伏
（交货时的默认位置）。
141页：为避免使用单电源时SA/SB出现错误指示，建议将输入端子SA/SB连接到
将CPU设置为+24 V，见图47。
143页：在AC 800M控制器正常通电并具备内存备份功能之前，不要连接TK821V020电缆
已激活，即B（蓄电池）LED闪烁。如果没有正常功率
电源连接到PM8xx处理器单元，CPU内存将
连接电缆后，立即开始消耗电池电量。
157页：在控制中设置主CPU的IP地址时
生成器，备份CPU必须关闭（断电）。否则
备份CPU将接管，您将断开连接。
159页：请注意，当AC 800M以单CPU配置运行时，电气模块总线只能用于连接S800 I/O。
184页：请注意，上出现严重通信错误的备份CPU
模块总线将被拒绝（如果模块总线是硬件配置的一部分），并且只要出现错误，就永远不会达到同步状态
残余
189页：冗余操作期间，不得从主处理器单元上拆下RCU链路电缆。电缆的拆除
可能导致装置停止。
192页：由于电池并联，
使用SB821外部电池时，要卸下内部电池
以避免减少可用内存备份时间。SPECIFIC
 CAUTIONS
(continued)
Page 76: Do not manipulate the locking device. ABB will take no responsibility for errors caused by manipulating locking devices.
-79 and Page 92: Do not place the internal back-up battery in the battery
holder until the AC 800M Controller has been powered-up normally and
the memory back-up function has been activated, that is, the B(attery)
LED flashes. If no normal power supply is connected to the processor unit
with the battery in place, then the CPU memory will immediately start to
consume battery power.
Page 90: Note that in redundant CPU configuration, COM3 and the electrical ModuleBus on the baseplate can not be used.
Page 91: Note that the RCU Link Cable TK851 must be used and can not
be replaced by a similar cable. Using another cable will disable the identification of the CPUs in the CB and Operator Station. When running in single configuration the RCU Link Cable TK851 might temporarily be used to
perform the function of a termination plug.
Page 98: Do not connect the two CEX-Bus segments, separated with
BC810, to each other with CEX-Bus extension cable TK850.
Page 98: In AC 800M High Integrity Controllers it is required that the external supply input of BC810 is connected and that the power supply is
strictly configured either according to Figure 33 or according to Figure 34
and nor is it allowed to change the configuration by way of for instance
individual circuit breakers between modules.
Page 99: Hot swap of the BC810 located next to a primary or single controller CPU, otherwise called “direct BC810”, might jeopardize the whole
controller and should not be performed unless every module on the
CEX-Bus are in a non-operating state. Note: In an AC 800M HI controller
this is unconditionally and intentionally leading to a shutdown of the controller.
Page 112: It is not possible to change the CI851 unit via hot swap and it is
not allowed to perform an online upgrade of firmware in a system containing CI851.
3BSE036351-510 A 21
Safety Summary (continued)
SPECIFIC
 CAUTIONS
(continued)
Page 114: It is not possible to change the CI852 unit via hot swap and it is
not allowed to perform an online upgrade of firmware in a system containing CI852.
Page 118: Hot swap is supported for CI854A (not CI854).
Page 133: – 115 V for 110–120 V AC – 230 V for 220–240 V AC
(default position on delivery).
Page 141: To avoid error indications from SA/SB when single power supply is used, it is recommended to connect the input terminals SA/SB on
the CPU to +24 V, see Figure 47.
Page 143: Do not connect the TK821V020 cable until the AC 800M Controller has been powered-up normally and the memory back-up function
has been activated, that is, the B(attery) LED flashes. If no normal power
supply is connected to the PM8xx processor unit, the CPU memory will
immediately start to consume battery power when the cable is connected.
Page 157: When setting the IP address of the primary CPU in Control
Builder, the backup CPU must be turned off (powered down). Otherwise
the backup CPU will take over and you get disconnected.
Page 159: Note that the electrical ModuleBus can only be used for connection of S800 I/O when AC 800M is running in single CPU configuration.
Page 184: Note that a Backup CPU with severe communication errors on
the ModuleBus will be rejected (if ModuleBus is part of the HW configuration) and synchronized state will never be reached as long as error
remains.
Page 189: The RCU Link Cable must NEVER be removed from the primary Processor Unit during redundant operation. Removal of the cable
may cause the unit to stop.
Page 192: Due to the batteries being connected in parallel, it is necessary,
when using the SB821 external battery, to remove the internal battery
from the PM8xx in order to avoid reducing available memory back-up time.