490NTW00005U模块备件

CI873和TP867-以太网/IP接口
具体的
警告
（续）
195页：由于电池并联连接，
使用SB821外部电池时，要卸下内部电池
来自处理器单元，以避免减少可用内存
备份时间。
-200和201页：重复使用同一控制网络内冗余配置替换的CPU模块，可能会导致控制网络
由于MAC和IP地址处理引起的问题。参见MAC和IP
49页冗余配置中的地址处理。这种重用
不应满足，除非更换的模块和模块
以前，在冗余配置中与it一起工作，已知：
从以前的相互地址交换中恢复。建议：
设置IP配置会话并使用“恢复出厂设置”选项
随后，重新分配IP地址或分配
新的IP地址。
200页：在任何情况下，请勿拆除RCU链路电缆
从现在以单一状态运行的主CPU。卸下电缆
可能导致CPU停止。
201页：通过以下方式，机组底板很容易彼此断开
用一字螺丝刀轻轻撬开它们（参见页的图23
74).
202页：不要在以前的版本中在线更换RCU链路电缆
5.0以上。对在线更换的支持也取决于硬件
产品修订级别。请参阅发行说明（3BSE021377*）
详细信息。
428页：如果您使用除SD82X和SD83X以外的其他电源
为AC 800M提供24V直流电。要求它们也是CE
已标记，保险商实验室（UL）列出并符合LVD（SELVandPELV）标准。
428页：AC 800M模块为IP20半保护设备，且
必须安装在非公共场所。
3BSE036351-510 A 23
关于本用户手册
全体的
本书描述了硬件平台AC 800M。它还详细描述了如何
安装、配置、操作和执行所有
构成AC 800M或AC 800M HI控制器的设备。
Control Builder用于配置和编程AC 800M控制器，并且
本手册中称为Control Builder。有关控制器的信息：
有关软件，请参阅控制器软件文档。
有关近更改的重要信息和已知的解决方案
问题，请参阅发行说明（请参阅发行的用户手册和发行说明
28页）。
用户手册约定
Microsoft Windows约定通常用于以下内容的标准表示：
输入文本、键序列、提示、消息、菜单项和屏幕时的材质
元素等。
本用户手册中描述的任何安全措施，例如
访问、密码安全、网络安全、防火墙、病毒保护等。，
表示800xA系统用户可能需要考虑的可能步骤
基于特定应用和安装的风险评估。这种风险
评估，以及适当的实施、配置、安装，
所有相关安全相关的操作、管理和维护
设备、软件和程序由
800xA系统。
关于本用户手册的警告、警告、信息和提示图标
24 3BSE036351-510 A
警告、警告、信息和提示图标
本出版物包括适当的警告、注意事项和信息
指出安全相关或其他重要信息。它还包括提示：
向读者指出有用的提示。相应的符号应为：
解释如下：
尽管警告危险与人身伤害有关，但警告危险是
与设备或财产损坏相关，应理解：
在某些操作条件下，损坏设备的操作可能导致
工艺性能下降，导致人身伤害或死亡。因此
完全遵守所有警告和注意事项。
术语
系统800xA系统中包含一个完整而全面的术语列表
功能描述指南（3BSE038018*）。该清单包括条款和
适用于800xA系统的定义，其中使用不同于
公认的行业标准定义和标准中给出的定义
字典，如韦氏计算机术语字典。
电气警告图标表示存在可能导致以下情况的危险：
电击。
警告图标表示存在可能导致人身伤害的危险
损伤
警告图标表示与概念相关的重要信息或警告
在本文中讨论。这可能表明存在危险，可能：
导致软件损坏或设备/财产损坏。
信息图标提醒读者相关事实和条件。
提示图标表示建议，例如，如何设计项目或如何
使用某个函数SPECIFIC
 CAUTIONS
(continued
Page 195: Due to the batteries being connected in parallel, it is necessary,
when using the SB821 external battery, to remove the internal battery
from the processor unit in order to avoid reducing available memory
back-up time.
-200 and Page 201: Reuse of CPU modules replaced from redundant configurations within the same control network, might cause control network
problems due to the MAC and IP address handling. See MAC and IP
Address Handling in Redundant Configuration on page 49. Such reuse
should not be fulfilled unless both the replaced module and the module
previously acting together with it in redundant configuration are known to
be restored from the previous mutual address swap. It is recommended to
set up an IP-config session and use the “Restore factory settings” option
subsequently followed by reassignment of the IP address or assignment
of a new IP address.
Page 200: Do not, under any circumstances, remove the RCU Link Cable
from the primary CPU now running in a single state. Removing the cable
might cause the CPU to stop.
Page 201: The unit baseplates are easily disconnected from each other by
gently prying them apart with a blade screwdriver (see Figure 23 on page
74).
Page 202: Do not replace the RCU link cable online in a previous version
than 5.0. The support for online replacement also depends on hardware
Product Revision levels. Please consult Release Notes (3BSE021377*)
for detailed information.
Page 428: If you use other power supplies, except SD82X and SD83X, to
provide the 24V d.c. for AC 800M it is required that they also are CE
marked, Underwriters Laboratories (UL ) listed and fulfill the LVD (SELVandPELV) criteria.
Page 428: The AC 800M modules are IP20 semi-protected equipment and
must be mounted in non-public localities.
3BSE036351-510 A 23
About This User Manual
General
This book describes the hardware platform AC 800M. It also describes in detail how
to install, configure, operate and perform the necessary maintenance on all
equipment making up the AC 800M or AC 800M HI controllers.
Control Builder is used to configure and program the AC 800M controller, and is
referred to in this manual as Control Builder. For information on the controller
software, see controller software documentation.
For important information about late changes and work-arounds for known
problems, refer to the Release Notes (see Released User Manuals and Release Notes
on page 28).
User Manual Conventions
Microsoft Windows conventions are normally used for the standard presentation of
material when entering text, key sequences, prompts, messages, menu items, screen
elements, etc.
Any security measures described in this User Manual, for example, for user
access, password security, network security, firewalls, virus protection, etc.,
represent possible steps that a user of an 800xA System may want to consider
based on a risk assessment for a particular application and installation. This risk
assessment, as well as the proper implementation, configuration, installation,
operation, administration, and maintenance of all relevant security related
equipment, software, and procedures, are the responsibility of the user of the
800xA System.
Warning, Caution, Information, and Tip Icons About This User Manual
24 3BSE036351-510 A
Warning, Caution, Information, and Tip Icons
This publication includes Warning, Caution, and Information where appropriate
to point out safety related or other important information. It also includes Tip to
point out useful hints to the reader. The corresponding symbols should be
interpreted as follows:
Although Warning hazards are related to personal injury, and Caution hazards are
associated with equipment or property damage, it should be understood that
operation of damaged equipment could, under certain operational conditions, result
in degraded process performance leading to personal injury or death. Therefore,
fully comply with all Warning and Caution notices.
Terminology
A complete and comprehensive list of terms is included in System 800xA System
Guide Functional Description (3BSE038018*). The listing includes terms and
definitions that apply to the 800xA System where the usage is different from
commonly accepted industry standard definitions and definitions given in standard
dictionaries such as Webster’s Dictionary of Computer Terms.
Electrical warning icon indicates the presence of a hazard which could result in
electrical shock.
Warning icon indicates the presence of a hazard which could result in personal
injury.
Caution icon indicates important information or warning related to the concept
discussed in the text. It might indicate the presence of a hazard which could
result in corruption of software or damage to equipment/property.
Information icon alerts the reader to pertinent facts and conditions.
Tip icon indicates advice on, for example, how to design your project or how to
use a certain function