490NTW00012模块备件

CI873和TP867-以太网/IP接口
下表列出了适用于本用户手册的ERM。
表1.术语
术语/首字母缩写描述
ABB驱动ABB Oy，驱动集团
AC 800M是硬件平台，
通信接口和其他支持设备，
其可以被配置为提供控制器。
AC 800M控制器：由AC 800M硬件配置的控制器
AC 800M平台和控制器FW。
AC 800M HI控制器：根据以下相关选择配置的控制器：
AC 800M硬件平台和控制器固件
AC 800M HI。
中央I/O输入/输出单元，直接安装在DIN导轨上
通过模块总线连接到AC 800M控制器。
CEX总线通信扩展总线（用于通信
单位）。
分布式驱动通信系统
DIN导轨是行业标准的“顶帽”型安装导轨。
专用于ABB驱动器的驱动总线通信链路。
DriveDebug诊断工具
DriveWindow调试和维护工具
电磁兼容性和电磁兼容性。
符合IEEE802.3的以太网网络布线系统。
以太网地址：术语以太网地址通常用于扩展
意思是指不仅是
以太网（IEEE 802.3）硬件，但也是无线的
（IEEE 802.11）硬件和FDDI（ISO 9314），另请参见
MAC地址。
FCI现场总线通信接口。
关于本用户手册的术语
26 3BSE036351-510 A
FF基金会现场总线-基于
IEC 1158-2。
FF HSE基金会现场总线-高速以太网，a
基于以太网和基金会的现场总线系统
现场总线规范。
具有热移除支持的热移除单元可以在线移除，
而不会对连接到
CEX巴士。这包括可以移除该装置
如果出现故障，则在线。
支持热插拔（包括热插拔）的热插拔单元，可以
在线更换，不会对其他设备造成任何干扰
连接到CEX总线的装置。在冗余系统中，
备用单元可以在没有任何故障的情况下更换
对一次机组的干扰。这包括：
如果装置出现故障，可以在线更换。
IEC国际电工委员会。
IEEE电气和电子工程师协会。
用于用户优化电机控制的INSUM集成系统。
LVD低压指令。
MAC地址：以太网所有硬件地址的通用术语
（IEEE 802.3）硬件、无线（IEEE802.11）硬件
并且FDDI（ISO 9314）是MAC地址；MAC代表
媒体访问控制。
骨盆由超低电压（电源）保护。
PROFIBUS DP开放式、独立于供应商的现场总线，用于时间关键型
控制器和分布式之间的通信
外围设备。
RCU冗余控制单元。erms that uniquely apply to this User Manual are listed in the following table.
Table 1. Terminology
Term/Acronym Description
ABB Drives ABB Oy, Drives Group
AC 800M A hardware platform, comprising Processor Units,
communication interfaces and other supporting devices,
that can be configured to provide a controller.
AC 800M Controller A controller configured from the AC 800M hardware
platform and Controller FW for AC 800M.
AC 800M HI Controller A controller configured from a relevant selection of the
AC 800M hardware platform and Controller Firmware for
AC 800M HI.
Central I/O Input/Output units, mounted onto a DIN-rail, and directly
connected to the AC 800M controller via ModuleBus.
CEX-Bus Communication Expansion Bus, (for communication
units).
DDCS Distributed Drives Communication System
DIN-rail Industry standard ‘Top Hat’ type mounting rail.
DriveBus Communication link dedicated for ABB drives.
DriveDebug Diagnostic Tool
DriveWindow Commissioning and Maintenance Tool
EMC Electro-Magnetic Compatibility.
Ethernet Network cabling system according to IEEE802.3.
Ethernet Address The term Ethernet address is often used in extended
meaning to refer to the hardware addresses of not only
Ethernet (IEEE 802.3) hardware, but also Wireless
(IEEE 802.11) hardware, and FDDI (ISO 9314), see also
MAC-address.
FCI Fieldbus Communication Interface.
Terminology About This User Manual
26 3BSE036351-510 A
FF FOUNDATION Fieldbus - Standard based on
IEC 1158-2.
FF HSE FOUNDATION Fieldbus - High Speed Ethernet, a
fieldbus system based on Ethernet and FOUNDATION
Fieldbus specification.
Hot removal Units with hot removal support can be removed online,
without any disturbance to other units connected to the
CEX-Bus. This includes that the unit can be removed
online if it becomes faulty.
Hot swap Units with hot swap (includes hot removal) support, can
be replaced online, without any disturbance to other
units connected to the CEX-Bus. In a redundant system,
the backup unit can be replaced without any
disturbances to the primary unit. This includes that the
unit can be replaced online if it becomes faulty.
IEC International Electrotechnical Commission.
IEEE Institute of Electrical and Electronic Engineers.
INSUM INtegrated System for User optimized Motor control.
LVD Low Voltage Directive.
MAC address The generic term for all hardware addresses of Ethernet
(IEEE802.3) hardware, Wireless (IEEE802.11) hardware
and FDDI (ISO 9314) is MAC address; MAC stands for
Media Access Control.
PELV Protected Extra Low Voltage (power supply).
PROFIBUS DP Open, vendor-independent fieldbus for time-critical
communication between controllers and distributed
peripherals.
RCU Redundancy Control Unit.