MSK040B-0450-NN-S1-UG0-NNNN模块现货

MSK040B-0450-NN-S1-UG0-NNNN

f您正在MVME945中安装多个MVME162
机箱，不要在插槽12中安装MVME162。高度
IP模块可能会在该插槽中造成间隙困难
位置
VMEbus上的其他MPU可以中断、禁用、与通信，以及
确定处理器的运行状态。GCSR的一个寄存器
（全局控制/状态寄存器）集合包括四位，用作位置
监视器允许一个MVME162处理器向任何其他处理器广播信号
MVME162处理器。所有八个寄存器都可以从任何本地访问
处理器以及来自VMEbus。
安装说明
MVME162/D2 2-13
2.MVME162为远程LED/开关连接器提供+5 Vdc电源
（J4）通过位于J4附近的1A保险丝（F1）。连接器J4是
远程控制和指示面板。如果没有指示灯点亮，则中止
如果复位开关不工作，检查保险丝F1。
MVME162为以太网收发器接口提供+12 Vdc电源
通过位于二极管CR1附近的1A保险丝（F2）。保险丝LED指示
+12 Vdc可用。当使用MVME712M模块时，黄色
当LAN电源可用时，MVME712M上的DS1 LED亮起
表示保险丝良好。如果以太网收发器无法运行，请检查
保险丝F2。
MVME162通过位于以下位置的1A保险丝（F1）提供SCSI终端电源：
DCD
MVME712M EIA-232-D DTE配置（至调制解调器）
712M过渡
模块
港口4
MVME 162 EIA-232-D DTE配置
（至调制解调器）
10970.00 (3-6) 9405
DSR
调制
712M EIA-232-D配置（至终端）
MVME 162 EIA-232-D DTE配置
（至调制解调器）
10970.00 (5-6) 9405
DSR
TXC
RXC
TXCO
DB25
1+5V
4.
2.
J15
P2-A32
P2-A28
RTXC
TRXC
1.在DTE模块和MVME 712跨接至端子的情况下，
时钟（TXC和RXC）方向错误。
RTXC4
TRXC4
数控
R
时钟都是输入。它们都应该是输出。
笔记：
2.使用DTE模块，B接口上85230的接收时钟
必须编程为输入，以防止BU

MSK040B-0450-NN-S1-UG0-NNNN

MSK040B-0450-NN-S1-UG0-NNNN

f you are installing multiple MVME162s in an MVME945
chassis, do not install an MVME162 in slot 12. The height of
the IP modules may cause clearance difficulties in that slot
position.
Other MPUs on the VMEbus can interrupt, disable, communicate with, and
determine the operational status of the processor(s). One register of the GCSR
(global control/status register) set includes four bits that function as location
monitors to allow one MVME162 processor to broadcast a signal to any other
MVME162 processors. All eight registers are accessible from any local
processor as well as from the VMEbus.
Installation Instructions
MVME162/D2 2-13
2 The MVME162 provides +5 Vdc power to the remote LED/switch connector
(J4) through a 1A fuse (F1) located near J4. Connector J4 is the interface for a
remote control and indicator panel. If none of the LEDs light and the ABORT
and RESET switches do not operate, check fuse F1.
The MVME162 provides +12 Vdc power to the Ethernet transceiver interface
through a 1A fuse (F2) located near diode CR1. The FUSE LED lights to indicate
that +12 Vdc is available. When the MVME712M module is used, the yellow
DS1 LED on the MVME712M illuminates when LAN power is available, which
indicates that the fuse is good. If the Ethernet transceiver fails to operate, check
fuse F2.
The MVME162 provides SCSI terminator power through a 1A fuse (F1) located

DCD
MVME712M EIA-232-D DTE CONFIGURATION (TO MODEM)
712M TRANSITION
MODULE
PORT 4
MVME 162 EIA-232-D DTE CONFIGURATION
 (TO MODEM)
10970.00 (3-6) 9405
DSR

TO MODEM
712M EIA-232-D CONFIGURATION (TO TERMINAL)
MVME 162 EIA-232-D DTE CONFIGURATION
 (TO MODEM)
10970.00 (5-6) 9405
DSR
TXC
RXC
TXCO
DB25
1 +5V
4
2
J15
P2-A32
P2-A28
RTXC
TRXC
1. WITH DTE MODULE AND MVME 712 JUMPERED AS TO TERMINAL,
 THE CLOCKS (TXC AND RXC) ARE THE WRONG DIRECTION.
RTXC4
TRXC4
NC
R
 THE CLOCKS ARE BOTH INPUTS. THEY SHOULD BOTH BE OUTPUTS.
NOTES:
 2. WITH DTE MODULE, THE RECEIVE CLOCK OF 85230 ON B INTERFACE
MUST BE PROGRAMMED AS INPUT TO PREVENT BU