6014BZ10000D -1640 125P2193-2 电路板PLC模块卡

6014BZ10000D -1640 125P2193-2 电路板PLC模块卡 

远程工程站，通过控制连接到另一个节点
网络
•记住，AC 800M控制器将在电压
应用。
采取措施使流程处于安全状态，提高了
电源、通信链路或控制系统部件时的安全
失败例如，这些步骤可能需要安装阀门或继电器
自动返回故障安全位置。
产品安全
必须始终遵守以下安全规则：
•为避免释放静电，将自己和任何工具接地
在处理印刷电路板、电池、存储卡和其他
设备的敏感部件
•所有电子设备对ESD（静电放电）敏感。到
处理印刷电路板时避免意外损坏
建议佩戴腕带，接地至底盘。带子必须
具有内置保护电阻器
•储存和运输时必须使用防静电导电塑料袋
运输中的PC板。
16 3BSE036351-510 A
安全摘要
更换装置前
维修
更换装置的所有程序可通过参考相关
文档
在系统电源连接的情况下拆卸或更换单元可能会导致人身伤害
人员和设备损坏。因此，这是至关重要的
拆除前，在工艺侧完全断开电源
或者进行单元的插入。
请参阅198页的装置在线更换和I/O文件。
建议保持适当的备件库存，以：
避免系统停机。
确保在以下位置制作当前应用程序的备份副本：
以避免系统停机。
3BSE036351-510 A 17
安全总结（续）
操作环境
在AC 800M控制器系统联机之前，调查
环境条件适用。特别注意到：
以下是：
•控制器不得暴露在超过给定值的条件下
在相关技术规范中。
•控制器不得在强电环境中使用
干扰电机会产生超过水平的干扰
允许用于设备，例如在维修工作期间。
•处理所有产品时，必须采取以下适当预防措施：
静电损坏。
•控制器不得直接暴露在阳光下。

6014BZ10000D -1640 125P2193-2 电路板PLC模块卡 

6014BZ10000D -1640 125P2193-2 电路板PLC模块卡 

remote engineering station, connected at another node via Control
Network.
• Remember, the AC 800M Controller will start automatically when voltage
is applied.
Taking steps to bring the process to a safe state, provides an improved level of
safety when power supplies, communication links or parts of the control system
fail. Such steps may require, for example, the installation of valves or relays that
automatically return to a fail-safe position.
Product Safety
The following safety rules must be observed at all times:
• To avoid discharging static electricity, ground both yourself and any tools
before handling printed circuit boards, batteries, memory cards, and other
sensitive pieces of the equipment
• All electronic devices are sensitive to ESD (electrostatic discharge). To
avoid accidental damage while handling printed circuit boards, it is
recommended to wear a wrist strap, grounded to the chassis. The strap must
have a built-in protective resistor
• Anti-static, conductive plastic bags must be used for storage and transport
of PC boards in transit.
16 3BSE036351-510 A
Safety Summary
Before replacing Units
Maintenance
All procedures for replacing units can be located by referring to the relevant
documentation.
Removing or replacing units with system power connected can cause injury to
personnel and damage to equipment. It is, therefore, of the utmost importance
that the power supply be fully disconnected, on the process side, before removal
or insertion of units takes place.
See Online Replacement of Unit on page 198 and I/O documentation.
It is recommended that a stock of suitable spare components be maintained to
avoid system downtime.
Ensure that back-up copies of the current application program are made at
regular, predetermined intervals to avoid system downtime.
3BSE036351-510 A 17
Safety Summary (continued)
Operating Environment
Before the AC 800M Controller system is brought online, investigate which
environmental conditions are applicable. Take note in particular of the
following:
• The controller must not be exposed to conditions that exceed the values given
in the relevant technical specifications.
• The controller must not be used in an environment exposed to strong electrical
interference. Electrical machines can produce interference that exceeds levels
permitted for the equipment, for example during repair work.
• All products must be handled with appropriate precautions with regard to
electrostatic damage.
• The controller must not be exposed to direct sunlight.