3183045486/0 LM 3183045486 模拟量输入控制板

3183045486/0 LM 3183045486 模拟量输入控制板 

如果已经安装，则从
处理器单元的侧面。
2.安装处理器单元、通信接口和S800 I/O
单位。
所有PM8xx的通信接口均位于左侧的CEX总线上
处理器单元。PM8xx的S800输入/输出单元位于电气上
处理器单元右侧的模块总线。
3.轻轻地将它们压在一起，并确保ModuleBus和CEXBus通过基板连接器正确连接。
4.将总线终端重新插入远的通信单元
来自处理器单元。
a、 对于CEX总线TB850（如果使用电缆TK850，则为TB851），参见图25
80页和81页的图26。使用BC810时，请参见
82页。如果在CEX总线上未使用任何单元，则不使用总线终端
必修的。
b、 有关ModuleBus TB807，请参阅S800 I/O文档。如果没有单位
如果在模块总线上使用，则不需要总线终端。
本主题不适用于PM891处理器单元。请参阅中的安装PM891
87页的单一配置。
对于PM861/PM864/PM865/PM866，插入RCU链路终端插头
TB852，位于RCU链路连接器处。必须始终使用终端插头
对于PM861/PM864/PM865/PM866，在单一配置下运行时。
当冗余处理器在单个配置中运行时，使用RCU
链路电缆TK851，如果RCU链路终端插头TB852不可用。
2节安装：在单个配置中安装PM86x/TP830处理器单元
3BSE036351-510 A 79
5.底板电缆连接：
a、 连接电源引线和电源监控信号（如适用）
从SS82x到螺钉端子SA和SB（参见83页图28）。
b、 将控制网络电缆连接至CN1（单连接）或CN1+
CN2（冗余连接）。
c、 将串行协议连接到COM3。
d、 使用电缆TK212将控制构建器连接到COM4（如果需要
改变IP地址等）。否则，将控件生成器连接到
控制网络。
6.将光学模块总线连接到处理器单元上的光学触点
（参见32页图2和131页图40）。关于
S800 I/O中提供了光缆选择和电缆长度
文档
7.PM8xx配有内部备用电池。当电池
使用时，将其放在内部电池支架中（参见193页的图63）。
当要使用外部SB821/SB822电池单元时，根据
请参阅页的安装SB821外部电池单元中的说明
143/安装144页的SB822可充电外部电池单元。
请注意，光学模块总线的连接与处理器的连接相同
用于S800 I/O中的FCI（参见160页图54）
不要将内部备用电池放在电池座中，直到
AC 800M控制器已正常通电，内存备份
功能已激活，即B（蓄电池）LED闪烁。如果不正常
电源连接到处理器单元，电池就位，然后
CPU内存将立即开始消耗电池电量。
在单个配置中安装PM86x/TP830处理器单元2节：安装
80 3BSE036351-510 A
安装结束时，务必安装新的内部或外部电池
阶段由于在运行期间频繁停电，原电池被大量使用
系统安装。
图25.CEX总线的TB850端子（公）
每个封装都提供一个TB850公CEX总线终端装置
（PM851K01、PM851AK01、PM 856K01、PM856AK01、PMC860K01、以及PM860AK01，
PM861K01、PM861AK01、PM 864K01、PM864AK01和PM865K01）
PM8xx/TP830处理器单元。
PM851/PM851A限制为多一个CEX模块。
终结者
TB850
2节安装：在单个配置中安装PM86x/TP830处理器单元
3BSE036351-510 A 81
图26.用于CEX总线的TB851端子（母）
终结者
TB851
TK850电缆
在单个配置中安装PM86x/TP830处理器单元2节：安装
82 3BSE036351-510 A
图27.使用BC810时的CEX总线终端
BC810
BC810
区域协调股链接
缆绳
PM861A/PM864A/PM865
终结者
TB850
终结者
TB850
2节安装：在单个配置中安装PM86x/TP830处理器单元
3BSE036351-510 A 83
图28.监控信号的SA/SB连接器
在单个配置中安装PM86x/TP830处理器单元2节：安装
84 3BSE036351-510 A
通信端口
CN1和CN2
控制网络连接到一个或两个RJ45连接器（CN1和CN2）
取决于网络选项（单个或冗余）。
使用IEEE802.3（以太网）的RJ45连接器连接到5类
屏蔽双绞线（STP 5级）。
5级或更高，电缆10/100BaseT/TX大100米（110码）。ABB建议：
在工业环境中使用光纤，例如62.5/125
100BaseFX，大距离1500米（1600码）。
表5.TP830 CN1和CN2连接

3183045486/0 LM 3183045486 模拟量输入控制板 

3183045486/0 LM 3183045486 模拟量输入控制板 

If already mounted, remove the CEX-Bus and ModuleBus terminations from
the sides of the processor unit.
2. Mount the processor unit, the communication interfaces, and the S800 I/O
units.
The communication interfaces for all PM8xx is on the CEX-Bus to the left of
the processor unit. The S800 I/O units for PM8xx is on the electrical
ModuleBus to the right of the processor unit.
3. Press them gently together and make sure that the ModuleBus and the CEXBus are correctly connected, via baseplate connectors.
4. Reinsert the bus terminations into the communication units at farthest away
from the processor unit.
a. For CEX-Bus TB850 (TB851 if cable TK850 is used), see Figure 25 on
page 80 and Figure 26 on page 81. When using BC810, see Figure 27 on
page 82. If no units are used on the CEX-Bus, no bus termination is
required.
b. For ModuleBus TB807, refer to the S800 I/O documentation. If no units
are used on the ModuleBus, no bus termination is required.
This topic does not apply to the PM891 processor unit. See Installing PM891 in
Single Configuration on page 87.
For PM861/PM864/PM865/PM866 insert the RCU Link Termination plug
TB852, at the RCU Link connector. The termination plug must always be used
for PM861/PM864/PM865/PM866 when running in single configuration.
When a redundant processor is running in a single configuration use the RCU
Link Cable TK851, if the RCU Link Termination plug TB852 is not available.
Section 2 Installation Installing the PM86x/TP830 Processor Unit in Single Configuration
3BSE036351-510 A 79
5. Baseplate cable connections:
a. Connect the power leads and, if applicable, power supervision signals
from SS82x to screw terminals SA and SB (see Figure 28 on page 83).
b. Connect the Control Network cables to CN1 (single connection) or CN1 +
CN2 (redundant connection).
c. Connect the serial protocol to COM3.
d. Connect the Control Builder to COM4 with cable TK212 (if required for
changing an IP address etc). Otherwise connect the Control Builder to the
Control Network.
6. Connect the optical ModuleBus to the optical contacts on the processor unit
(see Figure 2 on page 32 and Figure 40 on page 131). Information regarding
optical cable selection and cable length is provided in the S800 I/O
documentation.
7. The PM8xx is supplied with an internal back-up battery. When the battery is to
be used, place it in the Internal Battery Holder (see Figure 63 on page 193).
When the external SB821/SB822 battery unit is to be used, install it according
to the instructions in Installing the SB821 External Battery Unit on page
143/Installing the SB822 Rechargeable External Battery Unit on page 144.
Note that connection to the optical ModuleBus is identical to that for the processor
unit and for the FCI in S800 I/O (see Figure 54 on page 160.)
Do not place the internal back-up battery in the battery holder until the
AC 800M Controller has been powered-up normally and the memory back-up
function has been activated, that is, the B(attery) LED flashes. If no normal
power supply is connected to the processor unit with the battery in place, then
the CPU memory will immediately start to consume battery power.
Installing the PM86x/TP830 Processor Unit in Single Configuration Section 2 Installation
80 3BSE036351-510 A
Always install a fresh internal or external battery at the end of the installation
phase. The original battery is heavily utilized due to frequent blackouts during
system installation.
Figure 25. TB850 Terminator for CEX-Bus (male)
A TB850 male CEX-Bus termination unit is supplied with each package
(PM851K01, PM851AK01, PM856K01, PM856AK01, PM860K01, PM860AK01,
PM861K01, PM861AK01, PM864K01, PM864AK01 and PM865K01) of the
PM8xx/TP830 processor unit.
PM851/PM851A is restricted to a maximum of one CEX module.
Terminator
TB850
Section 2 Installation Installing the PM86x/TP830 Processor Unit in Single Configuration
3BSE036351-510 A 81
Figure 26. TB851 Terminator for CEX-Bus (female)
Terminator
TB851
TK850 Cable
Installing the PM86x/TP830 Processor Unit in Single Configuration Section 2 Installation
82 3BSE036351-510 A
Figure 27. CEX-Bus Terminator when using BC810
BC810
BC810
RCU Link
Cable
PM861A/PM864A/PM865
Terminator
TB850
Terminator
TB850
Section 2 Installation Installing the PM86x/TP830 Processor Unit in Single Configuration
3BSE036351-510 A 83
Figure 28. SA/SB Connectors for Supervision Signals
Installing the PM86x/TP830 Processor Unit in Single Configuration Section 2 Installation
84 3BSE036351-510 A
Communication Ports
CN1 and CN2
The control network connects to one or two RJ45 connectors (CN1 and CN2)
depending on network option (single or redundant).
Use an RJ45 connector for IEEE802.3 (Ethernet) for connecting to a category 5
Shielded Twisted Pair cable (STP class 5).
Class 5, or higher, cable 10/100BaseT/TX max 100 m (110 yd). ABB recommends
the use of optical fiber in an industrial environment, for example 62.5/125
100BaseFX, max. distance 1500 m (1600 yd).
Table 5. TP830 CN1 and CN2 Connections (RJ45 connectors)
Pin Designation Direction Description